List of XClarity Controller events
This section lists all messages that can be sent from the XClarity Controller.
FQXSPBR4000I: Management Controller [arg1]: Configuration restored from a file by user [arg2] from [arg3] at IP address [arg4].
This message is for the use case where a user restores a Management Controller configuration from a file.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0027
User Action:
Information only; no action is required
FQXSPBR4001I: Running the backup Management Controller [arg1] main application.
This message is for the use case where a Management Controller has resorted to running the backup main application.
- Severity: Warning
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0030
User Action:
Update the XCC firmware to a version that the server supports. Important: Some cluster solutions require specific code levels or coordinated code updates. If the device is part of a cluster solution, verify that the latest level of code is supported for the cluster solution before you update the code.
FQXSPBR4002I: Management Controller [arg1] Reset was caused by restoring default values.
This message is for the use case where a Management Controller has been reset due to a user restoring the configuration to default values.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0032
User Action:
Information only; no action is required
FQXSPBR4003I: Platform Watchdog Timer expired for [arg1].
This message is for the use case when an implementation has detected a Platform Watchdog Timer Expired
- Severity: Error
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - OS Timeout
- SNMP Trap ID: 21
- CIM Prefix: IMM CIM ID: 0039
User Action:
Complete the following steps until the problem is solved:- Reconfigure the watchdog timer to a higher value.
- Make sure that the XCC Ethernet-over-USB interface is enabled.
- Reinstall the RNDIS or cdc_ether device driver for the operating system.
- Disable the watchdog.
- Check the integrity of the installed operating system.
FQXSPBR4004I: Server timeouts set by user [arg1]: EnableOSWatchdog=[arg2], OSWatchdogTimout=[arg3], EnableLoaderWatchdog=[arg4], LoaderTimeout=[arg5].
A user configures Server Timeouts
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0095
User Action:
Information only; no action is required
FQXSPBR4005I: Management Controller [arg1]: Configuration saved to a file by user [arg2].
A user saves a Management Controller configuration to a file.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0109
User Action:
Information only; no action is required
FQXSPBR4006I: Management Controller [arg1]: Configuration restoration from a file by user [arg2] completed from [arg3] at IP address [arg4].
This message is for the use case where a user restores a Management Controller configuration from a file and it completes.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0136
User Action:
Information only; no action is required
FQXSPBR4007I: Management Controller [arg1]: Configuration restoration from a file by user [arg2] failed to complete from [arg3] at IP address [arg4].
This message is for the use case where a user restores a Management Controller configuration from a file and the restoration fails to complete.
- Severity: Error
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0137
User Action:
Complete the following steps until the problem is solved:- Turn off the server and disconnect it from the power source. You must disconnect the server from AC power cycle to reset the XCC.
- After 45 seconds, reconnect the server to the power source and turn on the server.
- Retry the operation.
FQXSPBR4008I: Management Controller [arg1]: Configuration restoration from a file by user [arg2] failed to start from [arg3] at IP address [arg4].
This message is for the use case where a user restores a Management Controller configuration from a file and the restoration fails to start.
- Severity: Error
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0138
User Action:
Complete the following steps until the problem is solved:- Turn off the server and disconnect it from the power source. You must disconnect the server from AC power cycle to reset the XCC.
- After 45 seconds, reconnect the server to the power source and turn on the server.
- Retry the operation.
FQXSPBR4009I: Management Controller [arg1]: cloning configuration from neighbor server [arg2] by group name [arg3].
This message is for the use case where a user synchronizes a Management Controller configuration by Federation.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0255
User Action:
Information only; no action is required
FQXSPBR400AI: Management Controller [arg1]: cloning configuration from neighbor server [arg2] by group name [arg3] completed.
This message is for the use case where a user synchronizes a Management Controller configuration by Federation and it completes.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0256
User Action:
Information only; no action is required
FQXSPBR400BI: Management Controller [arg1]: cloning configuration from neighbor server [arg2] by group name [arg3] failed to complete.
This message is for the use case where a user synchronizes a Management Controller configuration by Federation and the restoration fails to complete.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0257
User Action:
Information only; no action is required
FQXSPBR400CI: Management Controller [arg1]: cloning configuration from neighbor server [arg2] by group name [arg3] failed to start.
This message is for the use case where a user synchronizes a Management Controller configuration by Federation and the restoration fails to start.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0258
User Action:
Information only; no action is required
FQXSPBR400DI: Neighbor group clone configuration was initiated by user [arg1].
This message is for the user initiated a Federation clone configuration.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0259
User Action:
Information only; no action is required
FQXSPBR400EI: Neighbor group firmware update was initiated by user [arg1].
This message is for the user started a Federation update.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0260
User Action:
Information only; no action is required
FQXSPBR400FI: The neighbor group management is [arg1] by user [arg2] from [arg3] at IP address [arg4].
Neighbor group management is enabled or disabled by user
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0272
User Action:
Information only; no action is required
FQXSPBT0007I: No bootable media available for system [ComputerSystemElementName].
This message is for the use case when an implementation has detected a System with No Bootable Media.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: PLAT CIM ID: 0286
User Action:
Please ensure bootable media be installed correctly.
FQXSPCA0002M: Numeric sensor [NumericSensorElementName] going low (lower critical) has asserted.
This message is for the use case when an implementation has detected a Lower Critical sensor going low has asserted.
- Severity: Error
- Serviceable: Yes
- Automatically notify Support: Yes
- Alert Category: Critical - Fan Failure
- SNMP Trap ID: 11
- CIM Prefix: PLAT CIM ID: 0480
User Action:
Complete the following steps:- Check the event log of system management module and xClarity Controller for any fan or cooling-related issues or power-related issues.
- Make sure that the airflow at the front and rear of the chassis is not obstructed and that fillers are in place and correctly installed.
- Make sure that the room temperature is within operating specifications.
FQXSPCA0007J: Numeric sensor [NumericSensorElementName] going high (upper non-critical) has asserted.
This message is for the use case when an implementation has detected an Upper Non-critical sensor going high has asserted.
- Severity: Warning
- Serviceable: Yes
- Automatically notify Support: No
- Alert Category: Warning - Temperature
- SNMP Trap ID: 12
- CIM Prefix: PLAT CIM ID: 0490
User Action:
Complete the following steps:- Check the event log of system management module and xClarity Controller for any fan or cooling-related issues or power-related issues.
- Make sure that the airflow at the front and rear of the chassis is not obstructed and that fillers are in place and correctly installed.
- Make sure that the room temperature is within operating specifications.
FQXSPCA0009M: Numeric sensor [NumericSensorElementName] going high (upper critical) has asserted.
This message is for the use case when an implementation has detected an Upper Critical sensor going high has asserted.
- Severity: Error
- Serviceable: Yes
- Automatically notify Support: No
- Alert Category: Critical - Temperature
- SNMP Trap ID: 0
- CIM Prefix: PLAT CIM ID: 0494
User Action:
Complete the following steps:- Check the event log of system management module and xClarity Controller for any fan or cooling-related issues or power-related issues.
- Make sure that the airflow at the front and rear of the chassis is not obstructed and that fillers are in place and correctly installed.
- Make sure that the room temperature is within operating specifications.
FQXSPCA0011N: Numeric sensor [NumericSensorElementName] going high (upper non-recoverable) has asserted.
This message is for the use case when an implementation has detected an Upper Non-recoverable sensor going high has asserted.
- Severity: Error
- Serviceable: Yes
- Automatically notify Support: No
- Alert Category: Critical - Temperature
- SNMP Trap ID: 0
- CIM Prefix: PLAT CIM ID: 0498
User Action:
Complete the following steps:- Check the event log of system management module and xClarity Controller for any fan or cooling-related issues or power-related issues.
- Make sure that the airflow at the front and rear of the chassis is not obstructed and that fillers are in place and correctly installed.
- Make sure that the room temperature is within operating specifications.
FQXSPCA0015J: Sensor [SensorElementName] has transitioned from normal to non-critical state.
This message is for the use case when an implementation has detected a Sensor transitioned to non-critical from normal.
- Severity: Warning
- Serviceable: Yes
- Automatically notify Support: No
- Alert Category: Warning - Temperature
- SNMP Trap ID: 12
- CIM Prefix: PLAT CIM ID: 0520
User Action:
Complete the following steps:- Check the event log of system management module and xClarity Controller for any fan or cooling-related issues or power-related issues.
- Make sure that the airflow at the front and rear of the chassis is not obstructed and that fillers are in place and correctly installed.
- Make sure that the room temperature is within operating specifications.
FQXSPCA0017M: Sensor [SensorElementName] has transitioned to critical from a less severe state.
This message is for the use case when an implementation has detected a Sensor transitioned to critical from less severe.
- Severity: Error
- Serviceable: Yes
- Automatically notify Support: No
- Alert Category: Critical - Temperature
- SNMP Trap ID: 0
- CIM Prefix: PLAT CIM ID: 0522
User Action:
Complete the following steps:- Check the event log of system management module and xClarity Controller for any fan or cooling-related issues or power-related issues.
- Make sure that the airflow at the front and rear of the chassis is not obstructed and that fillers are in place and correctly installed.
- Make sure that the room temperature is within operating specifications.
FQXSPCA0019N: Sensor [SensorElementName] has transitioned to non-recoverable from a less severe state.
This message is for the use case when an implementation has detected a Sensor transitioned to non-recoverable from less severe.
- Severity: Error
- Serviceable: Yes
- Automatically notify Support: No
- Alert Category: Critical - Temperature
- SNMP Trap ID: 0
- CIM Prefix: PLAT CIM ID: 0524
User Action:
Complete the following steps:- Check the event log of system management module and xClarity Controller for any fan or cooling-related issues or power-related issues.
- Make sure that the airflow at the front and rear of the chassis is not obstructed and that fillers are in place and correctly installed.
- Make sure that the room temperature is within operating specifications.
FQXSPCA2002I: Numeric sensor [NumericSensorElementName] going low (lower critical) has deasserted.
This message is for the use case when an implementation has detected a Lower Critical sensor going low has deasserted.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Critical - Fan Failure
- SNMP Trap ID: 11
- CIM Prefix: PLAT CIM ID: 0481
User Action:
Information only; no action is required
FQXSPCA2007I: Numeric sensor [NumericSensorElementName] going high (upper non-critical) has deasserted.
This message is for the use case when an implementation has detected an Upper Non-critical sensor going high has deasserted.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Warning - Temperature
- SNMP Trap ID: 12
- CIM Prefix: PLAT CIM ID: 0491
User Action:
Information only; no action is required
FQXSPCA2009I: Numeric sensor [NumericSensorElementName] going high (upper critical) has deasserted.
This message is for the use case when an implementation has detected an Upper Critical sensor going high has deasserted.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Critical - Temperature
- SNMP Trap ID: 0
- CIM Prefix: PLAT CIM ID: 0495
User Action:
Information only; no action is required
FQXSPCA2011I: Numeric sensor [NumericSensorElementName] going high (upper non-recoverable) has deasserted.
This message is for the use case when an implementation has detected an Upper Non-recoverable sensor going high has deasserted.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Critical - Temperature
- SNMP Trap ID: 0
- CIM Prefix: PLAT CIM ID: 0499
User Action:
Information only; no action is required
FQXSPCA2015I: Sensor [SensorElementName] has deasserted the transition from normal to non-critical state.
This message is for the use case when an implementation has detected that a Sensor has deasserted a transition to non-critical from normal.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Warning - Temperature
- SNMP Trap ID: 12
- CIM Prefix: PLAT CIM ID: 0521
User Action:
Information only; no action is required
FQXSPCA2017I: Sensor [SensorElementName] has transitioned to a less severe state from critical.
This message is for the use case when an implementation has detected a Sensor transition to less severe from critical.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Critical - Temperature
- SNMP Trap ID: 0
- CIM Prefix: PLAT CIM ID: 0523
User Action:
Information only; no action is required
FQXSPCA2019I: Sensor [SensorElementName] has deasserted the transition to non-recoverable from a less severe state.
This message is for the use case when an implementation has detected that the Sensor transition to non-recoverable from less severe has deasserted.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Critical - Temperature
- SNMP Trap ID: 0
- CIM Prefix: PLAT CIM ID: 0525
User Action:
Information only; no action is required
FQXSPCN4000I: Serial Redirection set by user [arg1]: Mode=[arg2], BaudRate=[arg3], StopBits=[arg4], Parity=[arg5], SessionTerminateSequence=[arg6].
A user configured the Serial Port mode
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0078
User Action:
Information only; no action is required
FQXSPCN4001I: Remote Control session started by user [arg1] in [arg2] mode.
Remote Control session started
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0128
User Action:
Information only; no action is required
FQXSPCN4002I: User [arg1] has terminated an active CLI console session.
A user has terminated an active CLI console session
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0145
User Action:
Information only; no action is required
FQXSPCN4003I: Remote Control session started by user [arg1] in [arg2] mode has been closed.
Remote Control session closed
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0194
User Action:
Information only; no action is required
FQXSPCN4004I: User [arg1] has created an active [arg2] console session.
A user has created an IPMI/CLI console session
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0317
User Action:
Information only; no action is required
FQXSPCN4005I: A [arg1] console session is timeout.
An IPMI/CLI console session is timeout
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0318
User Action:
Information only; no action is required
FQXSPCN4006I: User [arg1] has terminated an active IPMI console session.
A user has terminated an active IPMI console session
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0319
User Action:
Information only; no action is required
FQXSPDM4000I: Inventory data changed for device [arg1], new device data hash=[arg2], new master data hash=[arg3] .
Something has caused the physical inventory to change
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0072
User Action:
Information only; no action is required
FQXSPDM4001I: Storage [arg1] has changed.
This message is for the use case where an IP address for the Storage Management has changed
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - IMM Network event
- SNMP Trap ID: 37
- CIM Prefix: IMM CIM ID: 0139
User Action:
Information only; no action is required
FQXSPDM4002I: Device [arg1] VPD is not valid.
The VPD for a device is invalid
- Severity: Warning
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0142
User Action:
Information only; no action is required
FQXSPDM4003I: TKLM servers set by user [arg1]: TKLMServer1=[arg2] Port=[arg3], TKLMServer2=[arg4] Port=[arg5], TKLMServer3=[arg6] Port=[arg7], TKLMServer4=[arg8] Port=[arg9].
A user configured the TKLM servers
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0146
User Action:
Information only; no action is required
FQXSPDM4004I: TKLM servers device group set by user [arg1]: TKLMServerDeviceGroup=[arg2] .
A user configured the TKLM device group
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0147
User Action:
Information only; no action is required
FQXSPDM4005I: User [arg1] has generated a new encryption key pair and installed a self-signed certificate for the TKLM client.
User generated a new encryption key pair and installed a self-signed certificate for the TKLM client
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0148
User Action:
Information only; no action is required
FQXSPDM4006I: User [arg1] has generated a new encryption key and certificate signing request for the TKLM client.
User generated a new encryption key and certificate signing request for the TKLM client
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0149
User Action:
Information only; no action is required
FQXSPDM4007I: User [arg1] has imported a signed certificate for the TKLM client from [arg2].
User imported a signed certificate for the TKLM client
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0150
User Action:
Information only; no action is required
FQXSPDM4008I: User [arg1] has imported a server certificate for the TKLM server.
User imported a server certificate for the TKLM Server
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0151
User Action:
Information only; no action is required
FQXSPDM4009I: User [arg1] has [arg2] file [arg3] from [arg4].
User has mounted/unmounted file from URL or server
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0162
User Action:
Information only; no action is required
FQXSPDM4011I: EKMS server protocol set by user [arg1]: TKLMServerProtocol=[arg2] .
A user configured the EKMS server protocol
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0293
User Action:
Information only; no action is required
FQXSPDM4012I: User [arg1] has changed the polling configuration for the key management server.: Polling enabled=[arg2] Interval=[arg3]
User changed the polling configuration for the key management server
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0334
User Action:
Information only; no action is required
FQXSPDM4013I: User [arg1] has changed the caching configuration for the key management server: Caching enabled=[arg2] Interval=[arg3]
User changed the caching configuration for the key management server
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0335
User Action:
Information only; no action is required
FQXSPEA0003J: Link down is detected on port [arg1] of the PCIe device [arg2].
This message is for the use case when an implementation has detected a Link down of PCIe device.
- Severity: Warning
- Serviceable: Yes
- Automatically notify Support: No
- Alert Category: Warning - Other
- SNMP Trap ID: 60
- CIM Prefix: PLAT CIM ID: 0520
User Action:
- Information only; no action is required.
- Note: This event will be set to Warning Severity for the LAN on Motherboard (LOM) interface and Informational Severity for all other Network Adapters present where link status can be monitored.
FQXSPEM4000I: The [arg1] on system [arg2] cleared by user [arg3].
This message is for the use case where a Management Controller Event Log on a system is cleared by a user.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0020
User Action:
Information only; no action is required
FQXSPEM4001I: The [arg1] on system [arg2] is 75% full.
This message is for the use case where a Management Controller Event Log on a system is 75% full.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Event Log Fullness
- SNMP Trap ID: 35
- CIM Prefix: IMM CIM ID: 0037
User Action:
Information only; no action is required
FQXSPEM4002I: The [arg1] on system [arg2] is 100% full.
This message is for the use case where a Management Controller Event Log on a system is 100% full.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Event Log Fullness
- SNMP Trap ID: 35
- CIM Prefix: IMM CIM ID: 0038
User Action:
To avoid losing older log entries, save the log as a text file and clear the log.
FQXSPEM4003I: LED [arg1] state changed to [arg2] by [arg3].
A user has modified the state of an LED
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0071
User Action:
Information only; no action is required
FQXSPEM4004I: SNMP [arg1] enabled by user [arg2] .
A user enabled SNMPv1 or SNMPv3 or Traps
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0073
User Action:
Information only; no action is required
FQXSPEM4005I: SNMP [arg1] disabled by user [arg2] .
A user disabled SNMPv1 or SNMPv3 or Traps
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0074
User Action:
Information only; no action is required
FQXSPEM4006I: Alert Configuration Global Event Notification set by user [arg1]: RetryLimit=[arg2], RetryInterval=[arg3], EntryInterval=[arg4].
A user changes the Global Event Notification settings.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0110
User Action:
Information only; no action is required
FQXSPEM4007I: Alert Recipient Number [arg1] updated: Name=[arg2], DeliveryMethod=[arg3], Address=[arg4], IncludeLog=[arg5], Enabled=[arg6], EnabledAlerts=[arg7], AllowedFilters=[arg8] by user [arg9] from [arg10] at IP address [arg11].
A user adds or updates an Alert Recipient
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0111
User Action:
Information only; no action is required
FQXSPEM4008I: SNMP Traps enabled by user [arg1]: EnabledAlerts=[arg2], AllowedFilters=[arg3] .
A user enabled the SNMP Traps configuration
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0112
User Action:
Information only; no action is required
FQXSPEM4009I: The UEFI Definitions have been changed.
UEFI Definitions change has been detected
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0152
User Action:
Information only; no action is required
FQXSPEM4010I: UEFI Reported: [arg1].
UEFI audit event logged.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0161
User Action:
Information only; no action is required
FQXSPEM4011I: XCC failed to log previous event [arg1].
XCC failed to log a previous event.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0196
User Action:
Information only; no action is required
FQXSPEM4012I: User [arg1] made system [arg2] Encapsulation lite Mode.
Encapsulation lite mode status change
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0201
User Action:
Information only; no action is required
FQXSPEM4013I: Battery error was detected by RAID controller. The battery unit needs replacement.([arg1],[arg2],[arg3],[arg4],[arg5])
Battery error was detected by RAID controller
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0202
User Action:
Information only; no action is required
FQXSPEM4014I: The RAID controller has problem with the battery. Please contact technical support to resolve this issue.([arg1],[arg2],[arg3],[arg4],[arg5])
The RAID controller has problem with the battery
- Severity: Info
- Serviceable: No
- Automatically notify Support: Yes
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0203
User Action:
Information only; no action is required
FQXSPEM4015I: The RAID controller detected unrecoverable error. The controller needs replacement.([arg1],[arg2],[arg3],[arg4],[arg5])
The RAID controller detected unrecoverable error
- Severity: Info
- Serviceable: No
- Automatically notify Support: Yes
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0204
User Action:
Information only; no action is required
FQXSPEM4016I: The RAID controller detected one or more problems. Please contact technical support for additional assistance.([arg1],[arg2],[arg3],[arg4],[arg5])
The RAID controller detected one or more problems
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0205
User Action:
Information only; no action is required
FQXSPEM4017I: The RAID controller detected one or more possible configuration changes within the subsystem. Please check the drive LED status. If necessary, contact technical support for additional assistance.([arg1],[arg2],[arg3],[arg4],[arg5])
The RAID controller detected one or more possible configuration changes within the subsystem
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0206
User Action:
Information only; no action is required
FQXSPEM4018I: Enclosure/Chassis issue detected with one or more units. Please check the enclosure/chassis units to repair the problem.([arg1],[arg2],[arg3],[arg4],[arg5])
Enclosure/Chassis issue detected with one or more units
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0207
User Action:
Information only; no action is required
FQXSPEM4019I: Connectivity issue detected with the enclosure/chassis. Please check your cable configurations to repair the problem.([arg1],[arg2],[arg3],[arg4],[arg5])
Connectivity issue detected with the enclosure/chassis
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0208
User Action:
Information only; no action is required
FQXSPEM4020I: Fan problem detected with the enclosure/chassis. Please check the enclosure/chassis unit fan for correct operation.([arg1],[arg2],[arg3],[arg4],[arg5])
Fan problem detected with the enclosure/chassis
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0209
User Action:
Information only; no action is required
FQXSPEM4022I: Enclosure/Chassis power supply has problem. Please check the enclosure/chassis unit power supply for correct operation.([arg1],[arg2],[arg3],[arg4],[arg5])
Enclosure/Chassis power supply has problem
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0210
User Action:
Information only; no action is required
FQXSPEM4023I: One or more virtual drive are in abnormal status that may cause unavailable virtual drive. Please check the event logs and if events are targeted to the same disk then replace the drive. If necessary, contact technical support for additional assistance.([arg1],[arg2],[arg3],[arg4],[arg5])
One or more virtual drive are in abnormal status that may cause unavailable virtual drive
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0211
User Action:
Information only; no action is required
FQXSPEM4024I: The RAID controller detected one or more possible configuration problem within the subsystem. Please check the event logs and if events are targeted to the same disk then replace the drive. If necessary, contact technical support for additional assistance.([arg1],[arg2],[arg3],[arg4],[arg5])
The RAID controller detected one or more possible configuration problem within the subsystem
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0212
User Action:
Information only; no action is required
FQXSPEM4025I: One or more virtual drive have problem. Please contact technical support to resolve this issue.([arg1],[arg2],[arg3],[arg4],[arg5])
One or more virtual drive have problem
- Severity: Info
- Serviceable: No
- Automatically notify Support: Yes
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0213
User Action:
Information only; no action is required
FQXSPEM4026I: Drive error was detected by RAID controller. Please contact technical support to resolve this issue.([arg1],[arg2],[arg3],[arg4],[arg5])
Drive error was detected by RAID controller
- Severity: Info
- Serviceable: No
- Automatically notify Support: Yes
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0214
User Action:
Information only; no action is required
FQXSPEM4027I: Drive error was detected by RAID controller. Please check the event logs and if events are targeted to the same disk then replace the drive. If necessary, contact technical support for additional assistance.([arg1],[arg2],[arg3],[arg4],[arg5])
Drive error was detected by RAID controller
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0215
User Action:
Information only; no action is required
FQXSPEM4028I: The port [arg1] of PCIe device [arg2] at [arg3] has link [arg4].
PCI device link
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0220
User Action:
Information only; no action is required
FQXSPEM4029I: All PCIe slots on [arg1] may not be functional based upon your current CPU population.
PCIe not be functional
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0221
User Action:
Information only; no action is required
FQXSPEM4030I: A scheduled operation on the RAID controller has encountered an issue. Refer to RAID Logs under Server Management, Local Storage, for details.([arg1],[arg2],[arg3],[arg4],[arg5])
The RAID controller has scheduled operation issue
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0223
User Action:
Information only; no action is required
FQXSPEM4031I: SSD wear threshold setting is changed from [arg1] to [arg2] by user [arg3] from [arg4] at IP address [arg5].
SSD wear threshold setting is changed by user
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0273
User Action:
Information only; no action is required
FQXSPEM4032I: Acoustic Mode [arg1] has been engaged. Fan speed limits are in place.
This message is for the use case where Acoustic Mode is engaged.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0274
User Action:
Information only; no action is required
FQXSPEM4033I: Acoustic Mode [arg1] has been disengaged to allow adequate cooling.
This message is for the use case where Acoustic Mode is disengaged.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0275
User Action:
Information only; no action is required
FQXSPEM4036I: Dust filter measurement schedule is configured on server [arg1] by user [arg2] from [arg3] at IP address [arg4].
Dust filter measurement schedule is configured
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0305
User Action:
Information only; no action is required
FQXSPEM4037I: Attempting to perform scheduled dust filter measurement on server [arg1].
Attempting to perform scheduled dust filter measurement
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0306
User Action:
Information only; no action is required
FQXSPEM4038I: Dust filter measurement schedule is disabled on server [arg1] by user [arg2] from [arg3] at IP address [arg4].
Dust filter measurement schedule is disabled
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0307
User Action:
Information only; no action is required
FQXSPEM4039I: Attempting to perform an immediate dust filter measurement on server [arg1] by user [arg2] from [arg3] at IP address [arg4].
Attempting to perform an immediate dust filter measurement
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0308
User Action:
Information only; no action is required
FQXSPEM4040I: Dust filter measurement is completed. The airflow pathway is obstructed, check and replace the dust filter, or remove any obstructing object.
Alert the user when dust filter measurement fails
- Severity: Warning
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0309
User Action:
Information only; no action is required
FQXSPEM4041I: The SmartNIC in slot [arg1] encountered boot timeout.
SmartNIC in a certain slot encountered boot timeout
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0312
User Action:
Information only; no action is required
FQXSPEM4042I: The SmartNIC in slot [arg1] went through a crash dump.
SmartNIC in a certain slot went through a crash dump
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0313
User Action:
Information only; no action is required
FQXSPEM4043I: A [arg1] failure has been detected and need [arg2] to recover.
backplane failure has detected
- Severity: Warning
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Warning - Other
- SNMP Trap ID: 60
- CIM Prefix: IMM CIM ID: 0320
User Action:
Information only; no action is required
FQXSPEM4044I: Dust filter measurement was successfully completed, no action is needed.
Alert the user when dust filter measurement is completed.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0321
User Action:
Information only; no action is required
FQXSPFC4000I: The bare metal connection process has been started.
Bare Metal Connection process has been started
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0143
User Action:
Information only; no action is required
FQXSPFC4001I: The bare metal update application reports a status of [arg1].
Bare Metal Update Application Status
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0144
User Action:
Information only; no action is required
FQXSPFC4002I: System running in setup.
System running in setup
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0193
User Action:
Information only; no action is required
FQXSPFC4003I: UEFI deployment boot mode is enabled for NextBoot.
UEFI deployment boot mode is enabled for NextBoot
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0197
User Action:
Information only; no action is required
FQXSPFC4004I: UEFI deployment boot mode is enabled for NextAc.
UEFI deployment boot mode is enabled for NextAC
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0198
User Action:
Information only; no action is required
FQXSPFC4005I: UEFI deployment boot mode has been disabled.
UEFI deployment boot mode has been disabled
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0199
User Action:
Information only; no action is required
FQXSPFW2001I: The System [ComputerSystemElementName] has detected a POST Error deassertion.
This message is for the use case when an implementation has detected that Post Error has deasserted.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Critical - Other
- SNMP Trap ID: 50
- CIM Prefix: PLAT CIM ID: 0185
User Action:
Information only; no action is required
FQXSPIO0003N: A diagnostic interrupt has occurred on system [ComputerSystemElementName].
This message is for the use case when an implementation has detected a Front Panel NMI / Diagnostic Interrupt.
- Severity: Error
- Serviceable: Yes
- Automatically notify Support: No
- Alert Category: Critical - Other
- SNMP Trap ID: 50
- CIM Prefix: PLAT CIM ID: 0222
User Action:
- If the NMI button on the operator information panel has not been pressed, complete the following steps:
- Reseat the identified compute node.
- If the problem still exist, replace the compute node.
- (Trained technician only)Replace the system board. Reseat the identified compute node.
- If error still exist, then replace compute node.
FQXSPIO0004L: A bus timeout has occurred on bus [SensorElementName].
This message is for the use case when an implementation has detected a Bus Timeout.
- Severity: Error
- Serviceable: Yes
- Automatically notify Support: No
- Alert Category: Critical - Other
- SNMP Trap ID: 50
- CIM Prefix: PLAT CIM ID: 0224
User Action:
Please reseat the processor and reboot the compute node. If the problem still exist, please replace the identified processor in the compute node.
FQXSPIO0006N: A software NMI has occurred on system [ComputerSystemElementName].
This message is for the use case when an implementation has detected a Software NMI.
- Severity: Error
- Serviceable: Yes
- Automatically notify Support: No
- Alert Category: Critical - Other
- SNMP Trap ID: 50
- CIM Prefix: PLAT CIM ID: 0228
User Action:
Check the event log in system management module (SMM) to resolve any issues related the NMI
FQXSPIO0011N: An Uncorrectable Error has occurred on [SensorElementName].
This message is for the use case when an implementation has detected a Bus Uncorrectable Error.
- Severity: Error
- Serviceable: Yes
- Automatically notify Support: Yes
- Alert Category: Critical - Other
- SNMP Trap ID: 50
- CIM Prefix: PLAT CIM ID: 0240
User Action:
- Check http://support.lenovo.com/ for TECH tips or firmware updates that might correct the error.
- Make sure that all I/O expansion adapters have correct and matching levels of device drivers and firmware.
- Check the event log of system management module(SMM) or xClarity Controller for additional information about failing components.
- If there are no entries related to the error in the event log, contact service.
FQXSPIO0015M: Fault in slot [PhysicalConnectorSystemElementName] on system [ComputerSystemElementName].
This message is for the use case when an implementation has detected a Fault in a slot.
- Severity: Error
- Serviceable: Yes
- Automatically notify Support: Yes
- Alert Category: Critical - Other
- SNMP Trap ID: 50
- CIM Prefix: PLAT CIM ID: 0330
User Action:
Complete the following steps until the problem is solved:- Reseat the affected adapters and riser card.
- Update the server firmware (UEFI and XCC) and adapter firmware.NoteSome cluster solutions require specific code levels or coordinated code updates.
- If the device is part of a cluster solution, verify that the latest level of code is supported for the cluster solution before you update the code.
- Replace the affected adapters.
- Replace the riser card.
- (Trained service technicians only) Replace the system board.
FQXSPIO2003I: System [ComputerSystemElementName] has recovered from a diagnostic interrupt.
This message is for the use case when an implementation has detected a recovery from a Front Panel NMI / Diagnostic Interrupt
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Critical - Other
- SNMP Trap ID: 50
- CIM Prefix: PLAT CIM ID: 0223
User Action:
Information only; no action is required
FQXSPIO2004I: Bus [SensorElementName] has recovered from a bus timeout.
This message is for the use case when an implementation has detected that a system has recovered from a Bus Timeout.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Critical - Other
- SNMP Trap ID: 50
- CIM Prefix: PLAT CIM ID: 0225
User Action:
Information only; no action is required
FQXSPIO2006I: System [ComputerSystemElementName] has recovered from an NMI.
This message is for the use case when an implementation has detected a Software NMI has been Recovered from.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Critical - Other
- SNMP Trap ID: 50
- CIM Prefix: PLAT CIM ID: 0230
User Action:
Information only; no action is required
FQXSPIO2015I: Fault condition removed on slot [PhysicalConnectorElementName] on system [ComputerSystemElementName].
This message is for the use case when an implementation has detected a Fault condition in a slot has been removed.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Critical - Other
- SNMP Trap ID: 50
- CIM Prefix: PLAT CIM ID: 0331
User Action:
Information only; no action is required.
FQXSPIO4001I: GPU Board Status was changed by [arg1] of [arg1].
This message is for the use case where GPU Board Status was changed.
- Severity: Warning
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0276
User Action:
Information only; no action is required
FQXSPIO4002I: GPU Board Status was recovered by [arg1] of [arg1].
This message is for the use case where GPU Board Status was changed.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0277
User Action:
Information only; no action is required
FQXSPMA0010J: [PhysicalMemoryElementName] on Subsystem [MemoryElementName] Throttled.
This message is for the use case when an implementation has detected Memory has been Throttled.
- Severity: Warning
- Serviceable: Yes
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: PLAT CIM ID: 0142
User Action:
Complete the following steps:- Check the event log of system management module and xClarity Controller for any fan or cooling related issues.
- Make sure that the airflow at the front and rear of the chassis is not obstructed and that fillers are in place and correctly installed.
- Make sure that the room temperature is within operating specifications.
- Make sure that the DIMM baffles are in place if applicable
- If the problem persists and there are no other DIMMs with the same indication, replace the DIMM.
FQXSPMA0012M: An Over-Temperature Condition has been detected on the [PhysicalMemoryElementName] on Subsystem [MemoryElementName].
This message is for the use case when an implementation has detected an Over Temperature Condition for Memory that has been Detected.
- Severity: Error
- Serviceable: Yes
- Automatically notify Support: No
- Alert Category: Critical - Temperature
- SNMP Trap ID: 0
- CIM Prefix: PLAT CIM ID: 0146
User Action:
Complete the following steps until the problem is solved:- Check the event log of system management module and xClarity Controller (XCC) for any fan- or cooling-related issues.
- Make sure that the airflow at the front and rear of the chassis is not obstructed and that fillers are in place and correctly installed.
- Make sure that the room temperature is within operating specifications.
- Make sure that the DIMM baffles are in place correctly.
- If the problem remains and no other DIMMs have the same indication, replace the DIMM.
FQXSPMA2005I: The System [ComputerSystemElementName] has detected a POST Error deassertion.
This message is for the use case when an implementation has detected that Post Error has deasserted.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Critical - Memory
- SNMP Trap ID: 41
- CIM Prefix: PLAT CIM ID: 0185
User Action:
Information only; no action is required
FQXSPMA2007I: Scrub Failure for [PhysicalMemoryElementName] on Subsystem [MemoryElementName] has recovered.
This message is for the use case when an implementation has detected a Memory Scrub failure recovery.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Critical - Memory
- SNMP Trap ID: 41
- CIM Prefix: PLAT CIM ID: 0137
User Action:
Information only; no action is required
FQXSPMA2010I: [PhysicalMemoryElementName] on Subsystem [MemoryElementName] is no longer Throttled.
This message is for the use case when an implementation has detected Memory is no longer Throttled.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: PLAT CIM ID: 0143
User Action:
Information only; no action is required
FQXSPMA2012I: An Over-Temperature Condition has been removed on the [PhysicalMemoryElementName] on Subsystem [MemoryElementName].
This message is for the use case when an implementation has detected an Over Temperature Condition for Memory that has been Removed.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Critical - Temperature
- SNMP Trap ID: 0
- CIM Prefix: PLAT CIM ID: 0147
User Action:
Information only; no action is required
FQXSPMA2013I: The System [ComputerSystemElementName] has detected a POST Error deassertion.
This message is for the use case when an implementation has detected that Post Error has deasserted.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Critical - Memory
- SNMP Trap ID: 41
- CIM Prefix: PLAT CIM ID: 0185
User Action:
Information only; no action is required
FQXSPNM4000I: Management Controller [arg1] Network Initialization Complete.
This message is for the use case where a Management Controller network has completed initialization.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - IMM Network event
- SNMP Trap ID: 37
- CIM Prefix: IMM CIM ID: 0001
User Action:
Information only; no action is required
FQXSPNM4001I: Ethernet Data Rate modified from [arg1] to [arg2] by user [arg3].
This message is for the use case where a user modifies the Ethernet Port data rate.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0003
User Action:
Information only; no action is required
FQXSPNM4002I: Ethernet Duplex setting modified from [arg1] to [arg2] by user [arg3].
This message is for the use case where A user modifies the Ethernet Port duplex setting.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0004
User Action:
Information only; no action is required
FQXSPNM4003I: Ethernet MTU setting modified from [arg1] to [arg2] by user [arg3].
This message is for the use case where a user modifies the Ethernet Port MTU setting.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0005
User Action:
Information only; no action is required
FQXSPNM4004I: Ethernet locally administered MAC address modified from [arg1] to [arg2] by user [arg3].
This message is for the use case where a user modifies the Ethernet Port MAC address setting.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0006
User Action:
Information only; no action is required
FQXSPNM4005I: Ethernet interface [arg1] by user [arg2].
This message is for the use case where a user enables or disabled the ethernet interface.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0007
User Action:
Information only; no action is required
FQXSPNM4006I: Hostname set to [arg1] by user [arg2].
This message is for the use case where user modifies the Hostname of a Management Controller.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - IMM Network event
- SNMP Trap ID: 37
- CIM Prefix: IMM CIM ID: 0008
User Action:
Information only; no action is required
FQXSPNM4007I: IP address of network interface modified from [arg1] to [arg2] by user [arg3].
This message is for the use case where user modifies the IP address of a Management Controller.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - IMM Network event
- SNMP Trap ID: 37
- CIM Prefix: IMM CIM ID: 0009
User Action:
Information only; no action is required
FQXSPNM4008I: IP subnet mask of network interface modified from [arg1] to [arg2] by user [arg3].
This message is for the use case where a user modifies the IP subnet mask of a Management Controller.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0010
User Action:
Information only; no action is required
FQXSPNM4009I: IP address of default gateway modified from [arg1] to [arg2] by user [arg3].
This message is for the use case where a user modifies the default gateway IP address of a Management Controller.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0011
User Action:
Information only; no action is required
FQXSPNM4010I: DHCP[[arg1]] failure, no IP address assigned.
This message is for the use case where a DHCP server fails to assign an IP address to a Management Controller.
- Severity: Warning
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - IMM Network event
- SNMP Trap ID: 37
- CIM Prefix: IMM CIM ID: 0013
User Action:
Complete the following steps until the problem is solved:- Make sure that the XCC network cable is connected.
- Make sure that there is a DHCP server on the network that can assign an IP address to the XCC.
FQXSPNM4011I: ENET[[arg1]] DHCP-HSTN=[arg2], DN=[arg3], IP@=[arg4], SN=[arg5], GW@=[arg6], DNS1@=[arg7] .
This message is for the use case where a Management Controller IP address and configuration has been assigned by the DHCP server.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - IMM Network event
- SNMP Trap ID: 37
- CIM Prefix: IMM CIM ID: 0022
User Action:
Information only; no action is required
FQXSPNM4012I: ENET[[arg1]] IP-Cfg:HstName=[arg2], IP@=[arg3] ,NetMsk=[arg4], GW@=[arg5] .
This message is for the use case where a Management Controller IP address and configuration has been assigned statically using user data.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - IMM Network event
- SNMP Trap ID: 37
- CIM Prefix: IMM CIM ID: 0023
User Action:
Information only; no action is required
FQXSPNM4013I: LAN: Ethernet[[arg1]] interface is no longer active.
This message is for the use case where a Management Controller ethernet interface is no longer active.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - IMM Network event
- SNMP Trap ID: 37
- CIM Prefix: IMM CIM ID: 0024
User Action:
Information only; no action is required
FQXSPNM4014I: LAN: Ethernet[[arg1]] interface is now active.
This message is for the use case where a Management Controller ethernet interface is now active.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - IMM Network event
- SNMP Trap ID: 37
- CIM Prefix: IMM CIM ID: 0025
User Action:
Information only; no action is required
FQXSPNM4015I: DHCP setting changed to [arg1] by user [arg2].
This message is for the use case where a user changes the DHCP setting.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0026
User Action:
Information only; no action is required
FQXSPNM4016I: Domain name set to [arg1] by user [arg2].
Domain name set by user
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0043
User Action:
Information only; no action is required
FQXSPNM4017I: Domain Source changed to [arg1] by user [arg2].
Domain source changed by user
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0044
User Action:
Information only; no action is required
FQXSPNM4018I: DDNS setting changed to [arg1] by user [arg2].
DDNS setting changed by user
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0045
User Action:
Information only; no action is required
FQXSPNM4019I: DDNS registration successful. The domain name is [arg1].
DDNS registration and values
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - IMM Network event
- SNMP Trap ID: 37
- CIM Prefix: IMM CIM ID: 0046
User Action:
Information only; no action is required
FQXSPNM4020I: IPv6 enabled by user [arg1] .
IPv6 protocol is enabled by user
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0047
User Action:
Information only; no action is required
FQXSPNM4021I: IPv6 disabled by user [arg1] .
IPv6 protocol is disabled by user
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0048
User Action:
Information only; no action is required
FQXSPNM4022I: IPv6 static IP configuration enabled by user [arg1].
IPv6 static address assignment method is enabled by user
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0049
User Action:
Information only; no action is required
FQXSPNM4023I: IPv6 DHCP enabled by user [arg1].
IPv6 DHCP assignment method is enabled by user
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0050
User Action:
Information only; no action is required
FQXSPNM4024I: IPv6 stateless auto-configuration enabled by user [arg1].
IPv6 stateless auto-assignment method is enabled by user
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0051
User Action:
Information only; no action is required
FQXSPNM4025I: IPv6 static IP configuration disabled by user [arg1].
IPv6 static assignment method is disabled by user
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0052
User Action:
Information only; no action is required
FQXSPNM4026I: IPv6 DHCP disabled by user [arg1].
IPv6 DHCP assignment method is disabled by user
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0053
User Action:
Information only; no action is required
FQXSPNM4027I: IPv6 stateless auto-configuration disabled by user [arg1].
IPv6 stateless auto-assignment method is disabled by user
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0054
User Action:
Information only; no action is required
FQXSPNM4028I: ENET[[arg1]] IPv6-LinkLocal:HstName=[arg2], IP@=[arg3] ,Pref=[arg4].
IPv6 Link Local address is active
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - IMM Network event
- SNMP Trap ID: 37
- CIM Prefix: IMM CIM ID: 0055
User Action:
Information only; no action is required
FQXSPNM4029I: ENET[[arg1]] IPv6-Static:HstName=[arg2], IP@=[arg3] ,Pref=[arg4], GW@=[arg5] .
IPv6 Static address is active
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - IMM Network event
- SNMP Trap ID: 37
- CIM Prefix: IMM CIM ID: 0056
User Action:
Information only; no action is required
FQXSPNM4030I: ENET[[arg1]] DHCPv6-HSTN=[arg2], DN=[arg3], IP@=[arg4], Pref=[arg5], DNS1@=[arg5].
IPv6 DHCP-assigned address is active
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - IMM Network event
- SNMP Trap ID: 37
- CIM Prefix: IMM CIM ID: 0057
User Action:
Information only; no action is required
FQXSPNM4031I: IPv6 static address of network interface modified from [arg1] to [arg2] by user [arg3].
A user modifies the IPv6 static address of a Management Controller
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0058
User Action:
Information only; no action is required
FQXSPNM4032I: DHCPv6 failure, no IP address assigned.
S DHCP6 server fails to assign an IP address to a Management Controller.
- Severity: Warning
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - IMM Network event
- SNMP Trap ID: 37
- CIM Prefix: IMM CIM ID: 0059
User Action:
Please ensure DHCP server is working.
FQXSPNM4033I: Telnet port number changed from [arg1] to [arg2] by user [arg3].
A user has modified the telnet port number
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0061
User Action:
Information only; no action is required
FQXSPNM4034I: SSH port number changed from [arg1] to [arg2] by user [arg3].
A user has modified the SSH port number
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0062
User Action:
Information only; no action is required
FQXSPNM4035I: Web-HTTP port number changed from [arg1] to [arg2] by user [arg3].
A user has modified the Web HTTP port number
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0063
User Action:
Information only; no action is required
FQXSPNM4036I: Web-HTTPS port number changed from [arg1] to [arg2] by user [arg3].
A user has modified the Web HTTPS port number
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0064
User Action:
Information only; no action is required
FQXSPNM4037I: CIM/XML HTTP port number changed from [arg1] to [arg2] by user [arg3].
A user has modified the CIM HTTP port number
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0065
User Action:
Information only; no action is required
FQXSPNM4038I: CIM/XML HTTPS port number changed from [arg1] to [arg2] by user [arg3].
A user has modified the CIM HTTPS port number
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0066
User Action:
Information only; no action is required
FQXSPNM4039I: SNMP Agent port number changed from [arg1] to [arg2] by user [arg3].
A user has modified the SNMP Agent port number
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0067
User Action:
Information only; no action is required
FQXSPNM4040I: SNMP Traps port number changed from [arg1] to [arg2] by user [arg3].
A user has modified the SNMP Traps port number
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0068
User Action:
Information only; no action is required
FQXSPNM4041I: Syslog port number changed from [arg1] to [arg2] by user [arg3].
A user has modified the Syslog receiver port number
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0069
User Action:
Information only; no action is required
FQXSPNM4042I: Remote Presence port number changed from [arg1] to [arg2] by user [arg3].
A user has modified the Remote Presence port number
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0070
User Action:
Information only; no action is required
FQXSPNM4043I: SMTP Server set by user [arg1] to [arg2]:[arg3].
A user configured the SMTP server
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0086
User Action:
Information only; no action is required
FQXSPNM4044I: Telnet [arg1] by user [arg2].
A user enables or disables Telnet services
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0087
User Action:
Information only; no action is required
FQXSPNM4045I: DNS servers set by user [arg1]: UseAdditionalServers=[arg2], PreferredDNStype=[arg3], IPv4Server1=[arg4], IPv4Server2=[arg5], IPv4Server3=[arg6], IPv6Server1=[arg7], IPv6Server2=[arg8], IPv6Server3=[arg9].
A user configures the DNS servers
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0088
User Action:
Information only; no action is required
FQXSPNM4046I: LAN over USB [arg1] by user [arg2].
A user configured USB-LAN
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0089
User Action:
Information only; no action is required
FQXSPNM4047I: LAN over USB Port Forwarding set by user [arg1]: ExternalPort=[arg2], USB-LAN port=[arg3].
A user configured USB-LAN port forwarding
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0090
User Action:
Information only; no action is required
FQXSPNM4048I: PXE boot requested by user [arg1].
PXE boot requested
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0129
User Action:
Information only; no action is required
FQXSPNM4049I: User [arg1] has initiated a TKLM Server Connection Test to check connectivity to server [arg2].
User initiated a TKLM Server Connection test.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0159
User Action:
Information only; no action is required
FQXSPNM4050I: User [arg1] has initiated an SMTP Server Connection Test.
User initiated an SMTP Server Connection test.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0160
User Action:
Information only; no action is required
FQXSPNM4051I: User [arg1] has set the SMTP Server reverse-path to [arg2].
User set SMTP Server reverse-path address
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0163
User Action:
Information only; no action is required
FQXSPNM4052I: DHCP specified hostname is set to [arg1] by user [arg2].
DHCP specified hostname is set by user
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0216
User Action:
Information only; no action is required
FQXSPNM4053I: DNS discovery of Lenovo XClarity Administrator has been [arg1] by user [arg2].
DNS discovery of Lenovo XClarity Administrator
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0217
User Action:
Information only; no action is required
FQXSPNM4054I: The hostname from DHCP is [arg1] by user [arg2].
This message is for getting hostname from DHCP.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - IMM Network event
- SNMP Trap ID: 37
- CIM Prefix: IMM CIM ID: 0244
User Action:
Information only; no action is required
FQXSPNM4055I: The hostname from DHCP is invalid.
This message is for hostname from DHCP is invalid.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - IMM Network event
- SNMP Trap ID: 37
- CIM Prefix: IMM CIM ID: 0245
User Action:
Information only; no action is required
FQXSPNM4056I: The NTP server address [arg1] is invalid.
Report NTP server invalid
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - IMM Network event
- SNMP Trap ID: 37
- CIM Prefix: IMM CIM ID: 0249
User Action:
Information only; no action is required
FQXSPNM4057I: Security: IP address: [arg1] had [arg2] login failures, it will be blocked to access for [arg3] minutes.
This message is for the use case where IP address blocking.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - IMM Network event
- SNMP Trap ID: 37
- CIM Prefix: IMM CIM ID: 0250
User Action:
Information only; no action is required
FQXSPNM4058I: IP address of network interface [arg1] is modified from [arg2] to [arg3] by user [arg4].
This message is for the use case where user modifies the IP address of a Management Controller.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - IMM Network event
- SNMP Trap ID: 37
- CIM Prefix: IMM CIM ID: 0286
User Action:
Information only; no action is required
FQXSPNM4059I: IP subnet mask of network interface [arg1] is modified from [arg2] to [arg3] by user [arg4].
This message is for the use case where a user modifies the IP subnet mask of a Management Controller.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0287
User Action:
Information only; no action is required
FQXSPNM4060I: IP address of default gateway of network interface [arg1] is modified from [arg2] to [arg3] by user [arg4].
This message is for the use case where a user modifies the default gateway IP address of a Management Controller.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0288
User Action:
Information only; no action is required
FQXSPOS4000I: OS Watchdog response [arg1] by [arg2] .
This message is for the use case where an OS Watchdog has been enabled or disabled by a user.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0012
User Action:
Information only; no action is required
FQXSPOS4001I: Watchdog [arg1] Screen Capture Occurred .
This message is for the use case where an operating system error has occurred and the screen was captured.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0028
User Action:
- If there was no operating-system error, complete the following steps until the problem is solved:
- Reconfigure the watchdog timer to a higher value.
- Make sure that the IMM Ethernet-over-USB interface is enabled.
- Reinstall the RNDIS or cdc_ether device driver for the operating system.
- Disable the watchdog.
- If there was an operating-system error, check the integrity of the installed operating system.
FQXSPOS4002I: Watchdog [arg1] Failed to Capture Screen.
This message is for the use case where an operating system error has occurred and the screen capture failed.
- Severity: Error
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0029
User Action:
Important: Some cluster solutions require specific code levels or coordinated code updates. If the device is part of a cluster solution, verify that the latest level of code is supported for the cluster solution before you update the code. Complete the following steps until the problem is solved:- Reconfigure the watchdog timer to a higher value.
- Make sure that the XCC Ethernet over USB interface is enabled.
- Reinstall the RNDIS or cdc_ether device driver for the operating system.
- Disable the watchdog.
- Check the integrity of the installed operating system.
- Update the XCC firmware.
FQXSPOS4003I: Platform Watchdog Timer expired for [arg1].
An implementation has detected an OS Loader Watchdog Timer Expired
- Severity: Error
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Loader timeout
- SNMP Trap ID: 26
- CIM Prefix: IMM CIM ID: 0060
User Action:
Complete the following steps until the problem is solved:- Reconfigure the watchdog timer to a higher value.
- Make sure that the XCC Ethernet-over-USB interface is enabled.
- Reinstall the RNDIS or cdc_ether device driver for the operating system.
- Disable the watchdog.
- Check the integrity of the installed operating system.
FQXSPOS4004I: Operating System status has changed to [arg1].
Operating System status change
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0191
User Action:
Information only; no action is required
FQXSPOS4005I: Host Power-On password changed by user [arg1] from [arg2] at IP address [arg3].
This message is for the use case where Host Power-On password changed.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0231
User Action:
Information only; no action is required
FQXSPOS4006I: Host Power-On password cleared by user [arg1] from [arg2] at IP address [arg3].
This message is for the use case where Host Power-On password cleared.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0232
User Action:
Information only; no action is required
FQXSPOS4007I: Host Admin password changed by user [arg1] from [arg2] at IP address [arg3].
This message is for the use case where Host Admin password changed.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0233
User Action:
Information only; no action is required
FQXSPOS4008I: Host Admin password cleared by user [arg1] from [arg2] at IP address [arg3].
This message is for the use case where Host Admin password cleared.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0234
User Action:
Information only; no action is required
FQXSPOS4009I: OS Crash Video Captured.
This message is for the use case where OS Crash Video Captured.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0235
User Action:
Information only; no action is required
FQXSPOS4010I: OS Crash Video Capture Failed.
This message is for the use case where OS Crash Video Capture Failed.
- Severity: Error
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0236
User Action:
Please reflash BMC to previous level and try again
FQXSPOS4011I: OS failure screen capture with hardware error is [arg1] by user [arg2] from [arg3] at IP address [arg4].
OS failure screen capture with hardware error is enabled or disabled by user.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0280
User Action:
Information only; no action is required
FQXSPOS4012I: POST watchdog Screen Capture Occurred.
This message is for the use case where an operating system error has occurred and the screen was captured.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0302
User Action:
Information only; no action is required
FQXSPPP4000I: Attempting to [arg1] server [arg2] by user [arg3].
This message is for the use case where a user is using the Management Controller to perform a power function on the system.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0015
User Action:
Information only; no action is required
FQXSPPP4001I: Server Power Off Delay set to [arg1] by user [arg2].
A user configured the Server Power Off Delay
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0081
User Action:
Information only; no action is required
FQXSPPP4002I: Server [arg1] scheduled for [arg2] at [arg3] by user [arg4].
A user configured a Server Power action at a specific time
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0082
User Action:
Information only; no action is required
FQXSPPP4003I: Server [arg1] scheduled for every [arg2] at [arg3] by user [arg4].
A user configured a recurring Server Power Action
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0083
User Action:
Information only; no action is required
FQXSPPP4004I: Server [arg1] [arg2] cleared by user [arg3].
A user cleared a Server Power Action.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0084
User Action:
Information only; no action is required
FQXSPPP4005I: The power cap value changed from [arg1] watts to [arg2] watts by user [arg3].
Power Cap values changed by user
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0113
User Action:
Information only; no action is required
FQXSPPP4006I: The minimum power cap value changed from [arg1] watts to [arg2] watts.
Minimum Power Cap value changed
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0114
User Action:
Information only; no action is required
FQXSPPP4007I: The maximum power cap value changed from [arg1] watts to [arg2] watts.
Maximum Power Cap value changed
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0115
User Action:
Information only; no action is required
FQXSPPP4008I: The soft minimum power cap value changed from [arg1] watts to [arg2] watts.
Soft Minimum Power Cap value changed
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0116
User Action:
Information only; no action is required
FQXSPPP4009I: The measured power value exceeded the power cap value.
Power exceeded cap
- Severity: Warning
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Warning - Power
- SNMP Trap ID: 164
- CIM Prefix: IMM CIM ID: 0117
User Action:
Information only; no action is required
FQXSPPP4010I: The new minimum power cap value exceeded the power cap value.
Minimum Power Cap exceeds Power Cap
- Severity: Warning
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Warning - Power
- SNMP Trap ID: 164
- CIM Prefix: IMM CIM ID: 0118
User Action:
Information only; no action is required
FQXSPPP4011I: Power capping was activated by user [arg1].
Power capping activated by user
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0119
User Action:
Information only; no action is required
FQXSPPP4012I: Power capping was deactivated by user [arg1].
Power capping deactivated by user
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0120
User Action:
Information only; no action is required
FQXSPPP4013I: Static Power Savings mode has been turned on by user [arg1].
Static Power Savings mode turned on by user
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0121
User Action:
Information only; no action is required
FQXSPPP4014I: Static Power Savings mode has been turned off by user [arg1].
Static Power Savings mode turned off by user
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0122
User Action:
Information only; no action is required
FQXSPPP4015I: Dynamic Power Savings mode has been turned on by user [arg1].
Dynamic Power Savings mode turned on by user
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0123
User Action:
Information only; no action is required
FQXSPPP4016I: Dynamic Power Savings mode has been turned off by user [arg1].
Dynamic Power Savings mode turned off by user
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0124
User Action:
Information only; no action is required
FQXSPPP4017I: Power cap and external throttling occurred.
Power cap and external throttling occurred
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0125
User Action:
Information only; no action is required
FQXSPPP4018I: External throttling occurred .
External throttling occurred
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0126
User Action:
Information only; no action is required
FQXSPPP4019I: Power cap throttling occurred.
Power cap throttling occurred
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0127
User Action:
Information only; no action is required
FQXSPPP4020I: The measured power value has returned below the power cap value.
Power exceeded cap recovered
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Warning - Power
- SNMP Trap ID: 164
- CIM Prefix: IMM CIM ID: 0130
User Action:
Information only; no action is required
FQXSPPP4021I: The new minimum power cap value has returned below the power cap value.
Minimum Power Cap exceeds Power Cap recovered
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Warning - Power
- SNMP Trap ID: 164
- CIM Prefix: IMM CIM ID: 0131
User Action:
Information only; no action is required
FQXSPPP4022I: The server was restarted for an unknown reason.
The server was restarted for an unknown reason
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0166
User Action:
Information only; no action is required
FQXSPPP4023I: The server is restarted by chassis control command.
Server is restarted by chassis control command
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0167
User Action:
Information only; no action is required
FQXSPPP4024I: The server was reset via push button.
Server was reset via push button
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0168
User Action:
Information only; no action is required
FQXSPPP4025I: The server was powered-up via power push button.
Server was power-up via power push button
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0169
User Action:
Information only; no action is required
FQXSPPP4026I: The server was restarted when the watchdog expired..
Server was restarted when the watchdog expired.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0170
User Action:
Information only; no action is required
FQXSPPP4027I: The server was restarted for OEM reason.
Server was restarted for OEM reason
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0171
User Action:
Information only; no action is required
FQXSPPP4028I: The server was automatically powered on because the power restore policy is set to always on.
Server was automatically powered on because the power restore policy is set to always on.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0172
User Action:
Information only; no action is required
FQXSPPP4029I: The server was automatically powered on because the power restore policy is set to restore previous power state..
Server was automatically powered on because the power restore policy is set to restore previous power state.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0173
User Action:
Information only; no action is required
FQXSPPP4030I: The server was reset via Platform Event Filter.
Server was reset via Platform Event Filter
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0174
User Action:
Information only; no action is required
FQXSPPP4031I: The server was power-cycled via Platform Event Filter.
Server was power-cycled via Platform Event Filter
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0175
User Action:
Information only; no action is required
FQXSPPP4032I: The server was soft reset.
Server was soft reset
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0176
User Action:
Information only; no action is required
FQXSPPP4033I: The server was powered up via Real Time Clock (scheduled power on).
Server was powered up via Real Time Clock (scheduled power on)
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0177
User Action:
Information only; no action is required
FQXSPPP4034I: The server was powered off for an unknown reason.
Server was powered off for an unknown reason
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0178
User Action:
Information only; no action is required
FQXSPPP4035I: The server was powered off by chassis control command.
Server was powered off by chassis control command
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0179
User Action:
Information only; no action is required
FQXSPPP4036I: The server was powered off via push button.
Server was powered off via push button
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0180
User Action:
Information only; no action is required
FQXSPPP4037I: The server was powered off when the watchdog expired.
Server was powered off when the watchdog expired.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0181
User Action:
Information only; no action is required
FQXSPPP4038I: The server stayed powered off because the power restore policy is set to always off.
Server stayed powered off because the power restore policy is set to always off.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0182
User Action:
Information only; no action is required
FQXSPPP4039I: The server stayed powered off because the power restore policy is set to restore previous power state..
Server stayed powered off because the power restore policy is set to restore previous power state.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0183
User Action:
Information only; no action is required
FQXSPPP4040I: The server was powered off via Platform Event Filter.
Server was power off via Platform Event Filter
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0184
User Action:
Information only; no action is required
FQXSPPP4041I: The server was powered off via Real Time Clock (scheduled power off).
Server was powered off via Real Time Clock (scheduled power off)
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0185
User Action:
Information only; no action is required
FQXSPPP4042I: Management Controller [arg1] reset was initiated due to Power-On-Reset.
Management Controller reset was initiated due to Power-On-Reset
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0186
User Action:
Information only; no action is required
FQXSPPP4043I: Management Controller [arg1] reset was initiated by PRESET.
Management Controller reset was initiated by PRESET
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0187
User Action:
Information only; no action is required
FQXSPPP4044I: Management Controller [arg1] reset was initiated by CMM.
Management Controller reset was initiated by CMM
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0188
User Action:
Information only; no action is required
FQXSPPP4045I: Management Controller [arg1] reset was initiated by XCC firmware.
Management Controller reset was initiated by XCC firmware
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0189
User Action:
Information only; no action is required
FQXSPPP4047I: Management Controller [arg1] reset was initiated by user [arg2].
This message is for the use case where a Management Controller reset is initiated by a user.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0021
User Action:
Information only; no action is required
FQXSPPP4048I: Attempting to AC power cycle server [arg1] by user [arg2].
AC power cycle server
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0227
User Action:
Information only; no action is required
FQXSPPP4049I: Management Controller [arg1] reset was initiated by Front Panel.
Management Controller reset was initiated by Front Panel
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0252
User Action:
Information only; no action is required
FQXSPPP4050I: Management Controller [arg1] reset was initiated to activate PFR Firmware.
Management Controller reset was initiated to activate PFR Firmware.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0253
User Action:
Information only; no action is required
FQXSPPP4051I: The progrmmable GPU total power capping value in slot [arg1] is changed to [arg2] watts by user [arg3] from [arg4] at IP address [arg5].
Progrmmable GPU total power capping changed by user
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0296
User Action:
Information only; no action is required
FQXSPPP4052I: The progrmmable GPU peak power capping value in slot [arg1] is changed to [arg2] watts by user [arg3] from [arg4] at IP address [arg5].
Progrmmable GPU peak power capping changed by user
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0297
User Action:
Information only; no action is required
FQXSPPP4053I: This message is reserved.
This message is reserved.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0301
User Action:
Information only; no action is required
FQXSPPP4054I: Unbalanced PSU config is detected, system is using less node PSU capacity.
This message is for the use case where user installed unbanlance PSU.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0316
User Action:
Information only; no action is required
FQXSPPR0000I: [ManagedElementName] detected as present.
This message is for the use case when an implementation has detected a Managed Element is now Present.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: PLAT CIM ID: 0390
User Action:
Information only; no action is required
FQXSPPR2001I: [ManagedElementName] detected as absent.
This message is for the use case when an implementation has detected a Managed Element is Absent.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: PLAT CIM ID: 0392
User Action:
Information only; no action is required
FQXSPPU0001N: An Over-Temperature Condition has been detected on [ProcessorElementName].
This message is for the use case when an implementation has detected an Over-Temperature Condition Detected for Processor.
- Severity: Error
- Serviceable: Yes
- Automatically notify Support: No
- Alert Category: Critical - Temperature
- SNMP Trap ID: 0
- CIM Prefix: PLAT CIM ID: 0036
User Action:
Complete the following steps until the problem is solved:- Check the event log of System Management Module (SMM) and XClarify Controller (XCC) for any fan- or cooling-related issues.
- Make sure that the airflow at the front and rear of the chassis is not obstructed and that fillers are in place and correctly installed.
- Make sure that the room temperature is within operating specifications.
- Make sure that the microprocessor 1 heat sink is securely installed.
- Make sure that the microprocessor 1 heat sink is installed correctly and the thermal material is correctly applied.
- (Trained technician only) Replace microprocessor 1.
FQXSPPU0002G: The Processor [ProcessorElementName] is operating in a Degraded State.
This message is for the use case when an implementation has detected a Processor is running in the Degraded state.
- Severity: Warning
- Serviceable: Yes
- Automatically notify Support: No
- Alert Category: Warning - CPU
- SNMP Trap ID: 42
- CIM Prefix: PLAT CIM ID: 0038
User Action:
Complete the following steps:- Check the event log of system management module and xClarity Controller for any fan or cooling-related issues or power-related issues.
- Make sure that the airflow at the front and rear of the chassis is not obstructed and that fillers are in place and correctly installed.
FQXSPPU0009N: [ProcessorElementName] has a Configuration Mismatch.
This message is for the use case when an implementation has detected a Processor Configuration Mismatch has occurred.
- Severity: Error
- Serviceable: Yes
- Automatically notify Support: No
- Alert Category: Critical - CPU
- SNMP Trap ID: 40
- CIM Prefix: PLAT CIM ID: 0062
User Action:
Complete the following steps until the problem is solved:- This message could occur with messages about other processor configuration problems. Resolve those messages first.
- If the problem persists, ensure that matching processors are installed (i.e., matching option part numbers, etc.).
- Verify that the processors are installed in the correct sockets according to the service information for this product. If not, correct that problem.
- Check Lenovo Support site for an applicable service bulletin or UEFI firmware update that applies to this processor error.
- If the problem persists, collect Service Data logs and contact Lenovo Support.
FQXSPPU2001I: An Over-Temperature Condition has been removed on [ProcessorElementName].
This message is for the use case when an implementation has detected a Over-Temperature Condition has been Removed for Processor.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Critical - Temperature
- SNMP Trap ID: 0
- CIM Prefix: PLAT CIM ID: 0037
User Action:
Information only; no action is required
FQXSPPU2002I: The Processor [ProcessorElementName] is no longer operating in a Degraded State.
This message is for the use case when an implementation has detected a Processor is no longer running in the Degraded state.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Warning - CPU
- SNMP Trap ID: 42
- CIM Prefix: PLAT CIM ID: 0039
User Action:
Information only; no action is required
FQXSPPW0001I: [PowerSupplyElementName] has been added to container [PhysicalPackageElementName].
This message is for the use case when an implementation has detected a Power Supply has been added.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: PLAT CIM ID: 0084
User Action:
Information only; no action is required
FQXSPPW0002L: [PowerSupplyElementName] has Failed.
This message is for the use case when an implementation has detected a Power Supply has failed.
- Severity: Error
- Serviceable: Yes
- Automatically notify Support: No
- Alert Category: Critical - Power
- SNMP Trap ID: 4
- CIM Prefix: PLAT CIM ID: 0086
User Action:
Please check event log in system management module (SMM) to identify the power supply unit failure
FQXSPPW0003G: Failure predicted on [PowerSupplyElementName].
This message is for the use case when an implementation has detected a Power Supply failure is predicted.
- Severity: Warning
- Serviceable: Yes
- Automatically notify Support: No
- Alert Category: Warning - Power
- SNMP Trap ID: 164
- CIM Prefix: PLAT CIM ID: 0088
User Action:
Please check event log in system management module (SMM) web interface to identify the predicted failure.
FQXSPPW0005I: [PowerSupplyElementName] is operating in an Input State that is out of range.
This message is for the use case when an implementation has detected a Power Supply that has input out of range.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: PLAT CIM ID: 0098
User Action:
Information only; no action is required
FQXSPPW0006I: [PowerSupplyElementName] has lost input.
This message is for the use case when an implementation has detected a Power Supply that has input that has been lost.
- Severity: Warning
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Warning - Power
- SNMP Trap ID:
- CIM Prefix: PLAT CIM ID: 0100
User Action:
Make sure power cables are connected correctly.
FQXSPPW0007L: [PowerSupplyElementName] has a Configuration Mismatch.
This message is for the use case when an implementation has detected a Power Supply with a Configuration Error.
- Severity: Error
- Serviceable: Yes
- Automatically notify Support: No
- Alert Category: Critical - Power
- SNMP Trap ID: 4
- CIM Prefix: PLAT CIM ID: 0104
User Action:
Check the event log in system management module (SMM) and product spec. in server setup guide.
FQXSPPW0008I: [SensorElementName] has been turned off.
This message is for the use case when an implementation has detected a Power Unit that has been Disabled.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Power Off
- SNMP Trap ID: 23
- CIM Prefix: PLAT CIM ID: 0106
User Action:
Information only; no action is required
FQXSPPW0009I: [PowerSupplyElementName] has been Power Cycled.
This message is for the use case when an implementation has detected a Power Unit that has been power cycled.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: PLAT CIM ID: 0108
User Action:
Information only; no action is required
FQXSPPW0031J: Numeric sensor [NumericSensorElementName] going low (lower non-critical) has asserted.
This message is for the use case when an implementation has detected a Lower Non-critical sensor going low has asserted.
- Severity: Warning
- Serviceable: Yes
- Automatically notify Support: No
- Alert Category: Warning - Voltage
- SNMP Trap ID: 13
- CIM Prefix: PLAT CIM ID: 0476
User Action:
CMOS battery is recommended to replace with new one.
FQXSPPW0035M: Numeric sensor [NumericSensorElementName] going low (lower critical) has asserted.
This message is for the use case when an implementation has detected a Lower Critical sensor going low has asserted.
- Severity: Error
- Serviceable: Yes
- Automatically notify Support: Yes
- Alert Category: Critical - Voltage
- SNMP Trap ID: 1
- CIM Prefix: PLAT CIM ID: 0480
User Action:
- Use one of the following procedures:
- If the specified sensor is Planar 3.3V or Planar 5V, (trained technician only)replace the system board.
- If the specified sensor is Planar 12V, check the System Management Module or xClarify Controller event log for power-supply-related issues, and resolve those issues.
- If the problem remains, replace (trained technician only)the system board.
FQXSPPW0047M: Numeric sensor [NumericSensorElementName] going high (upper critical) has asserted.
This message is for the use case when an implementation has detected an Upper Critical sensor going high has asserted.
- Severity: Error
- Serviceable: Yes
- Automatically notify Support: Yes
- Alert Category: Critical - Voltage
- SNMP Trap ID: 1
- CIM Prefix: PLAT CIM ID: 0494
User Action:
- Use one of the following procedures:
- If the specified sensor is Planar 3.3V or Planar 5V, (trained technician only)replace the system board.
- If the specified sensor is Planar 12V, check the System Management Module or xClarify Controller event log for power-supply-related issues, and resolve those issues.
- If the problem remains, replace (trained technician only)the system board."
FQXSPPW0057J: Sensor [SensorElementName] has transitioned from normal to non-critical state.
This message is for the use case when an implementation has detected a Sensor transitioned to non-critical from normal.
- Severity: Warning
- Serviceable: Yes
- Automatically notify Support: No
- Alert Category: Warning - Power
- SNMP Trap ID: 164
- CIM Prefix: PLAT CIM ID: 0520
User Action:
Please check event log in system manage module (SMM) web interface.
FQXSPPW0061M: Sensor [SensorElementName] has transitioned to critical from a less severe state.
This message is for the use case when an implementation has detected a Sensor transitioned to critical from less severe.
- Severity: Error
- Serviceable: Yes
- Automatically notify Support: No
- Alert Category: Critical - Power
- SNMP Trap ID: 4
- CIM Prefix: PLAT CIM ID: 0522
User Action:
Complete the following steps:- Ensure power supply unit to meet the system spec in wattage, efficiency level and supported list.
- Check the event log in system management module (SMM) to the detail information.
FQXSPPW0063M: Sensor [SensorElementName] has transitioned to critical from a less severe state.
This message is for the use case when an implementation has detected a Sensor transitioned to critical from less severe.
- Severity: Error
- Serviceable: Yes
- Automatically notify Support: Yes
- Alert Category: Critical - Voltage
- SNMP Trap ID: 1
- CIM Prefix: PLAT CIM ID: 0522
User Action:
Complete the following steps until the problem is solved:- Perform virtual system reseat or A/C power cycle.
- If the error persists, remove A/C power and any recently installed components.
- If the system successfully powers on, complete the following steps:
- Check the Server Proven website (http://www.lenovo.com/us/en/serverproven/index.shtml) to make sure that recently installed components are compatible with the system.
- Inspect the previously installed components for physical damage and fix it.
- If the system does not successfully power on or if this is not the first occurrence of this problem, go to step 4.
- If the system has stand-by power, collect Service Data logs.
- Contact Lenovo Support.
FQXSPPW2001I: [PowerSupplyElementName] has been removed from container [PhysicalPackageElementName].
This message is for the use case when an implementation has detected a Power Supply has been removed.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: PLAT CIM ID: 0085
User Action:
Information only; no action is required
FQXSPPW2002I: [PowerSupplyElementName] has returned to OK status.
This message is for the use case when an implementation has detected a Power Supply return to normal operational status.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Critical - Power
- SNMP Trap ID: 4
- CIM Prefix: PLAT CIM ID: 0087
User Action:
Information only; no action is required
FQXSPPW2003I: Failure no longer predicted on [PowerSupplyElementName].
This message is for the use case when an implementation has detected a Power Supply failure is no longer predicted.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Warning - Power
- SNMP Trap ID: 164
- CIM Prefix: PLAT CIM ID: 0089
User Action:
Information only; no action is required
FQXSPPW2005I: [PowerSupplyElementName] has returned to a Normal Input State.
This message is for the use case when an implementation has detected a Power Supply that has input that has returned to normal.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: PLAT CIM ID: 0099
User Action:
Information only; no action is required
FQXSPPW2006I: [PowerSupplyElementName] has returned to a Normal Input State.
This message is for the use case when an implementation has detected a Power Supply that has input that has returned to normal.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: PLAT CIM ID: 0099
User Action:
Information only; no action is required
FQXSPPW2007I: [PowerSupplyElementName] Configuration is OK.
This message is for the use case when an implementation when a Power Supply configuration is OK.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Critical - Power
- SNMP Trap ID: 4
- CIM Prefix: PLAT CIM ID: 0105
User Action:
Information only; no action is required
FQXSPPW2008I: [PowerSupplyElementName] has been turned on.
This message is for the use case when an implementation has detected a Power Unit that has been Enabled.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Power On
- SNMP Trap ID: 24
- CIM Prefix: PLAT CIM ID: 0107
User Action:
Information only; no action is required
FQXSPPW2031I: Numeric sensor [NumericSensorElementName] going low (lower non-critical) has deasserted.
This message is for the use case when an implementation has detected a Lower Non-critical sensor going low has deasserted.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Warning - Voltage
- SNMP Trap ID: 13
- CIM Prefix: PLAT CIM ID: 0477
User Action:
Information only; no action is required
FQXSPPW2035I: Numeric sensor [NumericSensorElementName] going low (lower critical) has deasserted.
This message is for the use case when an implementation has detected a Lower Critical sensor going low has deasserted.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Critical - Voltage
- SNMP Trap ID: 1
- CIM Prefix: PLAT CIM ID: 0481
User Action:
Information only; no action is required
FQXSPPW2047I: Numeric sensor [NumericSensorElementName] going high (upper critical) has deasserted.
This message is for the use case when an implementation has detected an Upper Critical sensor going high has deasserted.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Critical - Voltage
- SNMP Trap ID: 1
- CIM Prefix: PLAT CIM ID: 0495
User Action:
Information only; no action is required
FQXSPPW2057I: Sensor [SensorElementName] has deasserted the transition from normal to non-critical state.
This message is for the use case when an implementation has detected that a Sensor has deasserted a transition to non-critical from normal.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Warning - Power
- SNMP Trap ID: 164
- CIM Prefix: PLAT CIM ID: 0521
User Action:
Information only; no action is required
FQXSPPW2061I: Sensor [SensorElementName] has transitioned to a less severe state from critical.
This message is for the use case when an implementation has detected a Sensor transition to less severe from critical.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Critical - Power
- SNMP Trap ID: 4
- CIM Prefix: PLAT CIM ID: 0523
User Action:
Information only; no action is required
FQXSPPW2063I: Sensor [SensorElementName] has transitioned to a less severe state from critical.
This message is for the use case when an implementation has detected a Sensor transition to less severe from critical.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Critical - Voltage
- SNMP Trap ID: 1
- CIM Prefix: PLAT CIM ID: 0523
User Action:
Information only; no action is required
FQXSPPW4001I: PCIe Power Brake for [arg1] has been [arg2].
This message is for the use case where PCIe Power Brake.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0243
User Action:
Information only; no action is required
FQXSPPW4002I: Total graphics power value has exceeded the pre-configured limit.
This message is for the use case where total graphics power value value has exceeded the pre-configured limit.
- Severity: Warning
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Warning - Other
- SNMP Trap ID: 60
- CIM Prefix: IMM CIM ID: 0328
User Action:
Information only; no action is required
FQXSPPW4003I: The customized total graphics power is within the pre-configured limit.
This message is for the use case where the customized total graphics power is within the pre-configured limit.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0329
User Action:
Information only; no action is required
FQXSPSD0000I: The [StorageVolumeElementName] has been added.
This message is for the use case when an implementation has detected a Drive has been Added.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: PLAT CIM ID: 0162
User Action:
Information only; no action is required
FQXSPSD0001L: The [StorageVolumeElementName] has a fault.
This message is for the use case when an implementation has detected a Drive was Disabled due to fault.
- Severity: Error
- Serviceable: Yes
- Automatically notify Support: Yes
- Alert Category: Critical - Hard Disk drive
- SNMP Trap ID: 5
- CIM Prefix: PLAT CIM ID: 0164
User Action:
Complete the following steps:- Make sure that the reported device is compatible by checking https://serverproven.lenovo.com/.
- Collect the service data log from the management controller interface and contact Lenovo Support.
FQXSPSD0002G: Failure Predicted on [StorageVolumeElementName] for array [ComputerSystemElementName].
This message is for the use case when an implementation has detected an Array Failure is Predicted.
- Severity: Warning
- Serviceable: Yes
- Automatically notify Support: Yes
- Alert Category: System - Predicted Failure
- SNMP Trap ID: 27
- CIM Prefix: PLAT CIM ID: 0168
User Action:
Complete the following steps:- Replace the identified drive at the next maintenance period.
- If the problem persists after replacement, collect the service data log from the XCC WebGUI and contact Lenovo Support.
FQXSPSD0003I: Hot Spare enabled for [ComputerSystemElementName].
This message is for the use case when an implementation has detected a Hot Spare has been Enabled.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: PLAT CIM ID: 0170
User Action:
Information only; no action is required
FQXSPSD0005L: Array [ComputerSystemElementName] is in critical condition.
This message is for the use case when an implementation has detected that an Array is Critical.
- Severity: Error
- Serviceable: Yes
- Automatically notify Support: Yes
- Alert Category: Critical - Hard Disk drive
- SNMP Trap ID: 5
- CIM Prefix: PLAT CIM ID: 0174
User Action:
Replace the hard disk drive that is indicated by a lit status LED.
FQXSPSD0006L: Array [ComputerSystemElementName] has failed.
This message is for the use case when an implementation has detected that an Array Failed.
- Severity: Error
- Serviceable: Yes
- Automatically notify Support: Yes
- Alert Category: Critical - Hard Disk drive
- SNMP Trap ID: 5
- CIM Prefix: PLAT CIM ID: 0176
User Action:
Complete the following steps:- Replace any hard disk drive that is indicated by a lit status LED.
- Re-create the array.
- Restore the data from a backup.
FQXSPSD0007I: Rebuild in progress for Array in system [ComputerSystemElementName].
This message is for the use case when an implementation has detected that an Array Rebuild is in Progress.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: PLAT CIM ID: 0178
User Action:
Information only; no action is required
FQXSPSD2000I: The [StorageVolumeElementName] has been removed from unit [PhysicalPackageElementName].
This message is for the use case when an implementation has detected a Drive has been Removed.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: PLAT CIM ID: 0163
User Action:
Complete the following steps until the problem is solved:- If drive was intentionally removed, make sure that there is a filler in the drive bay.
- Make sure that the drive is correctly seated.
- If drive is correctly seated, replace the drive.
FQXSPSD2001I: The [StorageVolumeElementName] has recovered from a fault.
This message is for the use case when an implementation has detected a Drive was Enabled.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Critical - Hard Disk drive
- SNMP Trap ID: 5
- CIM Prefix: PLAT CIM ID: 0167
User Action:
Information only; no action is required
FQXSPSD2002I: Failure no longer Predicted on [StorageVolumeElementName] for array [ComputerSystemElementName].
This message is for the use case when an implementation has detected an Array Failure is no longer Predicted.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Predicted Failure
- SNMP Trap ID: 27
- CIM Prefix: PLAT CIM ID: 0169
User Action:
Information only; no action is required
FQXSPSD2003I: Hot spare disabled for [ComputerSystemElementName].
This message is for the use case when an implementation has detected a Hot Spare has been Disabled.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: PLAT CIM ID: 0171
User Action:
Information only; no action is required
FQXSPSD2005I: Critical Array [ComputerSystemElementName] has deasserted.
This message is for the use case when an implementation has detected that a Critical Array has deasserted.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Critical - Hard Disk drive
- SNMP Trap ID: 5
- CIM Prefix: PLAT CIM ID: 0175
User Action:
Information only; no action is required
FQXSPSD2006I: Array in system [ComputerSystemElementName] has been restored.
This message is for the use case when an implementation has detected that a Failed Array has been Restored.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Critical - Hard Disk drive
- SNMP Trap ID: 5
- CIM Prefix: PLAT CIM ID: 0177
User Action:
Information only; no action is required
FQXSPSD2007I: Rebuild completed for Array in system [ComputerSystemElementName].
This message is for the use case when an implementation has detected that an Array Rebuild has Completed.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: PLAT CIM ID: 0179
User Action:
Information only; no action is required
FQXSPSE4000I: Certificate Authority [arg1] has detected a [arg2] Certificate Error.
This message is for the use case when there is an error with an SSL Server, SSL Client, or SSL Trusted CA Certificate.
- Severity: Error
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0002
User Action:
Make sure that the certificate that you are importing is correct and properly generated.
FQXSPSE4001I: Remote Login Successful. Login ID: [arg1] using [arg2] from [arg3] at IP address [arg4].
This message is for the use case where a user successfully logs in to a Management Controller.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Remote Login
- SNMP Trap ID: 30
- CIM Prefix: IMM CIM ID: 0014
User Action:
Information only; no action is required
FQXSPSE4002I: Security: Userid: [arg1] using [arg2] had [arg3] login failures from WEB client at IP address [arg4].
This message is for the use case where a user has failed to log in to a Management Controller from a web browser.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Remote Login
- SNMP Trap ID: 30
- CIM Prefix: IMM CIM ID: 0016
User Action:
Complete the following steps until the problem is solved:- Make sure that the correct login ID and password are being used.
- Have the system administrator reset the login ID or password.
FQXSPSE4003I: Security: Login ID: [arg1] had [arg2] login failures from CLI at [arg3].
This message is for the use case where a user has failed to log in to a Management Controller from the Legacy CLI.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Remote Login
- SNMP Trap ID: 30
- CIM Prefix: IMM CIM ID: 0017
User Action:
Complete the following steps until the problem is solved:- Make sure that the correct login ID and password are being used.
- Have the system administrator reset the login ID or password.
FQXSPSE4004I: Remote access attempt failed. Invalid userid or password received. Userid is [arg1] from WEB browser at IP address [arg2].
This message is for the use case where a remote user has failed to establish a remote control session from a Web browser session.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Remote Login
- SNMP Trap ID: 30
- CIM Prefix: IMM CIM ID: 0018
User Action:
Make sure that the correct login ID and password are being used.
FQXSPSE4005I: Remote access attempt failed. Invalid userid or password received. Userid is [arg1] from TELNET client at IP address [arg2].
This message is for the use case where a user has failed to log in to a Management Controller from a telnet session.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Remote Login
- SNMP Trap ID: 30
- CIM Prefix: IMM CIM ID: 0019
User Action:
Make sure that the correct login ID and password are being used.
FQXSPSE4007I: Security: Userid: [arg1] using [arg2] had [arg3] login failures from an SSH client at IP address [arg4].
This message is for the use case where a user has failed to log in to a Management Controller from SSH.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Remote Login
- SNMP Trap ID: 30
- CIM Prefix: IMM CIM ID: 0041
User Action:
Complete the following steps until the problem is solved:- Make sure that the correct login ID and password are being used.
- Have the system administrator reset the login ID or password.
FQXSPSE4008I: SNMPv1 [arg1] set by user [arg2]: Name=[arg3], AccessType=[arg4], Address=[arg5], .
A user changed the SNMP community string
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0075
User Action:
Information only; no action is required
FQXSPSE4009I: LDAP Server configuration set by user [arg1]: SelectionMethod=[arg2], DomainName=[arg3], Server1=[arg4], Server2=[arg5], Server3=[arg6], Server4=[arg7].
A user changed the LDAP server configuration
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0076
User Action:
Information only; no action is required
FQXSPSE4010I: LDAP set by user [arg1]: RootDN=[arg2], UIDSearchAttribute=[arg3], BindingMethod=[arg4], EnhancedRBS=[arg5], TargetName=[arg6], GroupFilter=[arg7], GroupAttribute=[arg8], LoginAttribute=[arg9].
A user configured an LDAP Miscellaneous setting
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0077
User Action:
Information only; no action is required
FQXSPSE4011I: Secure Web services (HTTPS) [arg1] by user [arg2].
A user enables or disables Secure web services
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0091
User Action:
Information only; no action is required
FQXSPSE4012I: Secure CIM/XML(HTTPS) [arg1] by user [arg2].
A user enables or disables Secure CIM/XML services
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0092
User Action:
Information only; no action is required
FQXSPSE4013I: Secure LDAP [arg1] by user [arg2].
A user enables or disables Secure LDAP services
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0093
User Action:
Information only; no action is required
FQXSPSE4014I: SSH [arg1] by user [arg2].
A user enables or disables SSH services
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0094
User Action:
Information only; no action is required
FQXSPSE4015I: Global Login General Settings set by user [arg1]: AuthenticationMethod=[arg2], LockoutPeriod=[arg3], SessionTimeout=[arg4].
A user changes the Global Login General Settings
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0098
User Action:
Information only; no action is required
FQXSPSE4016I: Global Login Account Security set by user [arg1]: PasswordRequired=[arg2], PasswordExpirationPeriod=[arg3], MinimumPasswordReuseCycle=[arg4], MinimumPasswordLength=[arg5], MinimumPasswordChangeInterval=[arg6], MaxmumLoginFailures=[arg7], LockoutAfterMaxFailures=[arg8].
A user changes the Global Login Account Security Settings to Legacy
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0099
User Action:
Information only; no action is required
FQXSPSE4017I: User [arg1] created.
A user account was created
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0100
User Action:
Information only; no action is required
FQXSPSE4018I: User [arg1] removed.
A user account was deleted
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0101
User Action:
Information only; no action is required
FQXSPSE4019I: User [arg1] password modified.
A user account was changed
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0102
User Action:
Information only; no action is required
FQXSPSE4020I: User [arg1] role set to [arg2].
A user account role assigned
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0103
User Action:
Information only; no action is required
FQXSPSE4021I: User [arg1] custom privileges set: [arg2][arg3][arg4][arg5][arg6][arg7][arg8][arg9].
User account privileges assigned
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0104
User Action:
Information only; no action is required
FQXSPSE4022I: User [arg1] for SNMPv3 set: AuthenticationProtocol=[arg2], PrivacyProtocol=[arg3], AccessType=[arg4], HostforTraps=[arg5] by user [arg6] from [arg7] at IP address [arg8].
User account SNMPv3 settings changed
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0105
User Action:
Information only; no action is required
FQXSPSE4023I: SSH Client key added for user [arg1] by user [arg2] from [arg3] at IP address [arg4].
User locally defined an SSH Client key
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0106
User Action:
Information only; no action is required
FQXSPSE4024I: SSH Client key imported for user [arg1] from [arg2] by user [arg3] from [arg4] at IP address [arg5].
User imported an SSH Client key
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0107
User Action:
Information only; no action is required
FQXSPSE4025I: SSH Client key removed from user [arg1] by user [arg2] from [arg3] at IP address [arg4].
User removed an SSH Client key
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0108
User Action:
Information only; no action is required
FQXSPSE4026I: Security: Userid: [arg1] had [arg2] login failures from a CIM client at IP address [arg3].
This message is for the use case where a user has failed to log in to a Management Controller from CIM.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Remote Login
- SNMP Trap ID: 30
- CIM Prefix: IMM CIM ID: 0140
User Action:
Information only; no action is required
FQXSPSE4027I: Remote access attempt failed. Invalid userid or password received. Userid is [arg1] from a CIM client at IP address [arg2].
This message is for the use case where a remote user has failed to establish a remote control session from CIM.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Remote Login
- SNMP Trap ID: 30
- CIM Prefix: IMM CIM ID: 0141
User Action:
Information only; no action is required
FQXSPSE4028I: Security: Userid: [arg1] had [arg2] login failures from IPMI client at IP address [arg3].
This message is for the use case where a user has failed to log in to a Management Controller from IPMI.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Remote Login
- SNMP Trap ID: 30
- CIM Prefix: IMM CIM ID: 0153
User Action:
Information only; no action is required
FQXSPSE4029I: Security: Userid: [arg1] had [arg2] login failures from SNMP client at IP address [arg3].
This message is for the use case where a user has failed to access a Management Controller from SNMP.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Remote Login
- SNMP Trap ID: 30
- CIM Prefix: IMM CIM ID: 0154
User Action:
Information only; no action is required
FQXSPSE4030I: Security: Userid: [arg1] had [arg2] login failures from IPMI serial client.
This message is for the use case where a user has failed to log in to a Management Controller from IPMI serial client
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Remote Login
- SNMP Trap ID: 30
- CIM Prefix: IMM CIM ID: 0155
User Action:
Information only; no action is required
FQXSPSE4031I: Remote Login Successful. Login ID: [arg1] from [arg2] serial interface.
This message is for the use case where a user successfully logs in to a Management Controller.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Remote Login
- SNMP Trap ID: 30
- CIM Prefix: IMM CIM ID: 0156
User Action:
Information only; no action is required
FQXSPSE4032I: Login ID: [arg1] from [arg2] at IP address [arg3] has logged off.
This message is for the use case where a user has logged off of a Management Controller.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Remote Login
- SNMP Trap ID: 30
- CIM Prefix: IMM CIM ID: 0157
User Action:
Information only; no action is required
FQXSPSE4033I: Login ID: [arg1] from [arg2] at IP address [arg3] has been logged off.
This message is for the use case where a user has been logged off of a Management Controller.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Remote Login
- SNMP Trap ID: 30
- CIM Prefix: IMM CIM ID: 0158
User Action:
Information only; no action is required
FQXSPSE4034I: User [arg1] has removed a certificate.
User removed certificate
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0164
User Action:
Information only; no action is required
FQXSPSE4035I: A certificate has been revoked .
A certificate has been revoked
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0165
User Action:
Information only; no action is required
FQXSPSE4036I: The [arg1] certificate is expired and has been removed.
Expired certificate has been removed
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0190
User Action:
Information only; no action is required
FQXSPSE4037I: Crypto mode modified from [arg1] to [arg2] by user [arg3].
Crypto mode modified
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0218
User Action:
Information only; no action is required
FQXSPSE4038I: Minimum TLS level modified from [arg1] to [arg2] by user [arg3].
Minimum TLS level modified
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0219
User Action:
Information only; no action is required
FQXSPSE4039I: Temporary user account [arg1] is created by inband tool.
Temporary user account create
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0228
User Action:
One user account is created
FQXSPSE4040I: Temporary user account [arg1] expires.
Temporary user account expire
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0229
User Action:
The user account you input is expired
FQXSPSE4041I: Security: Userid: [arg1] had [arg2] login failures from a SFTP client at IP address [arg3].
This message is for the use case where a user has failed to log in to a Management Controller from SFTP.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Remote Login
- SNMP Trap ID: 30
- CIM Prefix: IMM CIM ID: 0230
User Action:
Information only; no action is required
FQXSPSE4042I: The third-party password function [arg1] by user [arg2] from [arg3] at IP address [arg4].
This message is for the use case where a user successfully switch the third-party password function.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0238
User Action:
Information only; no action is required
FQXSPSE4043I: Retrieving the third-party password [arg1] by user [arg2] from [arg3] at IP address [arg4].
This message is for the use case where a user successfully switch the retrieving the third-party password.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0239
User Action:
Information only; no action is required
FQXSPSE4044I: User [arg1] third-party hashed password has been [arg2] by user [arg3] from [arg4] at IP address [arg5].
This message is for the use case where a user successfully manage the third-party hashed password.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0240
User Action:
Information only; no action is required
FQXSPSE4045I: The Salt of user [arg1] third-party password has been [arg2] by user [arg3] from [arg4] at IP address [arg5].
This message is for the use case where a user successfully manage the third-party password salt.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0241
User Action:
Information only; no action is required
FQXSPSE4046I: The third-party password of the user [arg1] has been retrieved by user [arg2] from [arg3] at IP address [arg4].
This message is for the use case where a user successfully retrieving the third-party password.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0242
User Action:
Information only; no action is required
FQXSPSE4047I: Role [arg1] is [arg2] and assigned with custom privileges [arg3][arg4][arg5][arg6][arg7][arg8][arg9][arg10][arg11] by user [arg12] .
Role create modify and assign
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0246
User Action:
Information only; no action is required
FQXSPSE4048I: Role [arg1] is removed by user [arg2].
Role is removed
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0247
User Action:
Information only; no action is required
FQXSPSE4049I: Role [arg1] is assigned to user [arg2] by user [arg3].
Role is assigned
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0248
User Action:
Information only; no action is required
FQXSPSE4050I: [arg1] sent IPMI command from [arg2], raw data: [arg3][arg4][arg5].
This message is for the use case where IPMI command to be sent.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0251
User Action:
Information only; no action is required
FQXSPSE4051I: Management Controller [arg1] joined the neighbor group [arg2] by user [arg3] at IP address [arg4].
This message is for the use case where MC joins a group.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0261
User Action:
Information only; no action is required
FQXSPSE4052I: The password of neighbor group [arg1] is modified by [arg2] [arg3] at IP address [arg4].
This message is for the use case where the group user password is modified.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0262
User Action:
Information only; no action is required
FQXSPSE4053I: Management Controller [arg1] left the neighbor group [arg2] by user [arg3] at IP address [arg4].
This message is for the use case where MC leaves a group.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0263
User Action:
Information only; no action is required
FQXSPSE4054I: IPMI SEL wrapping mode is [arg1] by user [arg2] at IP address [arg3].
IPMI SEL wrapping mode is changed.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0264
User Action:
Information only; no action is required
FQXSPSE4055I: SED encryption is enabled by user [arg1] at IP address [arg2].
SED encryption is enabled.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0265
User Action:
Information only; no action is required
FQXSPSE4056I: SED AK is [arg1] by user [arg2] at IP address [arg3].
SED AK is regenerated or recovered.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0266
User Action:
Information only; no action is required
FQXSPSE4057I: User [arg1] created by user [arg2] from [arg3] at IP address [arg4].
A user account was created by user
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0267
User Action:
Information only; no action is required
FQXSPSE4058I: User [arg1] removed by user [arg2] from [arg3] at IP address [arg4].
A user account was deleted by user
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0268
User Action:
Information only; no action is required
FQXSPSE4059I: User [arg1] password modified by user [arg2] from [arg3] at IP address [arg4].
A user account was changed by user
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0269
User Action:
Information only; no action is required
FQXSPSE4060I: User [arg1] role set to [arg2] by user [arg3] from [arg4] at IP address [arg5].
A user account role assigned by user
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0270
User Action:
Information only; no action is required
FQXSPSE4061I: User [arg1] custom privileges set: [arg2][arg3][arg4][arg5][arg6][arg7][arg8][arg9] by user [arg10] from [arg11] at IP address [arg12].
User account privileges assigned by user
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0271
User Action:
Information only; no action is required
FQXSPSE4062I: The system guard snapshot is captured by user [arg1] from [arg2] at IP address [arg3].
The system guard snapshot is captured by user.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0278
User Action:
Information only; no action is required
FQXSPSE4063I: The system guard configuration is updated: status=[arg1], hardware inventory=[arg2] and action=[arg3] by user [arg4] from [arg5] at IP address [arg6].
The system guard configuration is updated by user.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0279
User Action:
Information only; no action is required
FQXSPSE4064I: SNMPv3 engine ID is changed from [arg1] to [arg2] by user [arg3] from [arg4] at IP address [arg5].
SNMPv3 engine ID changed
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0282
User Action:
Information only; no action is required
FQXSPSE4065I: SFTP [arg1] by user [arg2] from [arg3] at IP address [arg4].
A user enables and disables SFTP service
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0283
User Action:
Information only; no action is required
FQXSPSE4066I: Security mode is modified from [arg1] to [arg2] by user [arg3] from [arg4] at IP address [arg5].
Security mode modified by user
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0284
User Action:
Information only; no action is required
FQXSPSE4067I: User [arg1] accessible interfaces is set to [arg2][arg3][arg4][arg5][arg6] by user [arg7] from [arg8] at IP address [arg9].
User account accessible interfaces assigned by user
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0285
User Action:
Information only; no action is required
FQXSPSE4068I: Security: Userid: [arg1] using [arg2] had [arg3] login failures from Redfish client at IP address [arg4].
This message is for the use case where a user has failed to log in to a Management Controller from Redfish.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Remote Login
- SNMP Trap ID: 30
- CIM Prefix: IMM CIM ID: 0289
User Action:
Information only; no action is required
FQXSPSE4069I: LDAP set by user [arg1]: RootDN=[arg2], UIDSearchAttribute=[arg3], BindingMethod=[arg4], TargetName=[arg5], GroupFilter=[arg6], GroupAttribute=[arg7], LoginAttribute=[arg8].
A user configured an LDAP Miscellaneous setting
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0290
User Action:
Information only; no action is required
FQXSPSE4070I: Lockdown mode is [arg1] by user [arg2] from [arg3] at IP address [arg4].
A user enables or disables Lockdown mode
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0291
User Action:
Information only; no action is required
FQXSPSE4071I: Chassis Intrusion detection is [arg1] by user [arg2] from [arg3] at IP address [arg4].
A user enables or disables Chassis Intrusion detection
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0292
User Action:
Information only; no action is required
FQXSPSE4072I: Random SED AK is regenerated by user [arg1] from [arg2] at IP address [arg3].
A user regenerates a random SED AK
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0294
User Action:
Information only; no action is required
FQXSPSE4073I: Motion detection is [arg1] by user [arg2] from [arg3] at IP address [arg4].
Motion detection is enabled or disabled by user
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0295
User Action:
Information only; no action is required
FQXSPSE4074I: Security mode downgrades because the XCC2 Platinum Upgrade key is expired or deleted.
This message is for the use case where security mode downgrades because XCC2 Platinum Upgrade key is expired or deleted.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0300
User Action:
Information only; no action is required
FQXSPSE4075I: [arg1] by KCS to allow secure boot to be enabled by user [arg2] from [arg3] at IP address [arg4].
Allow Secure boot to be enabled over KCS
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0310
User Action:
Information only; no action is required
FQXSPSE4076I: [arg1] by KCS to allow secure boot to be disabled by user [arg2] from [arg3] at IP address [arg4].
Allow Secure boot to be disabled over KCS
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0311
User Action:
Information only; no action is required
FQXSPSE4077I: Bluetooth button on front panel is [arg1] on server [arg2] by user [arg3] from [arg4] at IP address [arg5].
Bluetooth button on front panel is enabled/disabled by user
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0314
User Action:
Information only; no action is required
FQXSPSE4078I: Bluetooth is [arg1] by pressing bluetooth button on front pannel.
Bluetooth is enabled/disabled by pressing bluetooth button on front pannel
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0315
User Action:
Information only; no action is required
FQXSPSE4079I: The Operator role is [arg1] to contain Remote Console Access permission by user [arg2] from [arg3] at IP address [arg4].
Update privilege to enable/disable Operator to access Remote Console
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0322
User Action:
Information only; no action is required
FQXSPSE4080I: The user [arg1] attempts to clear CMOS from [arg2] at IP address [arg4].
User attempts to clear CMOS
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0323
User Action:
Information only; no action is required
FQXSPSE4081I: BMC returns the valid local cached key to UEFI for SED drives.
This message is for the use case where BMC returns the local cached key to UEFI for SED drives.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0327
User Action:
Information only; no action is required
FQXSPSE4082I: Remote key management server is unaccessable.
This message is for the use case where remote key management server is unaccessable.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0330
User Action:
Information only; no action is required
FQXSPSE4083I: The local cached key has expired and destroyed it.
This message is for the use case where the local cached key has expired and destroyed it.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0331
User Action:
Information only; no action is required
FQXSPSE4084I: Periodic connection to remote key management server succeeded.
This message is for the use case where the remote key management server poll function has succeeded.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0332
User Action:
Information only; no action is required
FQXSPSE4085I: Periodic connection to remote key management server failed.
This message is for the use case where the remote key management server poll function has failed.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0333
User Action:
Information only; no action is required
FQXSPSE4088I: The chassis care-taker node ID is changed from [arg1] to [arg2].
This message is for the use case where chassis caretaker node is changed.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0336
User Action:
Information only; no action is required
FQXSPSE4089I: The chassis node with node ID [arg1] is inserted.
This message is for the use case where node is inserted into the chassis.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0337
User Action:
Information only; no action is required
FQXSPSE4090I: The chassis node with node ID [arg1] is removed.
This message is for the use case where node is removed from the chassis.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0338
User Action:
Information only; no action is required
FQXSPSS4000I: Management Controller Test Alert Generated by [arg1].
This message is for the use case where a user has generated a Test Alert.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0040
User Action:
Information only; no action is required
FQXSPSS4001I: Server General Settings set by user [arg1]: Name=[arg2], Contact=[arg3], Location=[arg4], Room=[arg5], RackID=[arg6], Rack U-position=[arg7], Address=[arg8].
A user configured the Location setting
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0080
User Action:
Information only; no action is required
FQXSPSS4002I: License key for [arg1] added by user [arg2].
A user installs License Key
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0096
User Action:
Information only; no action is required
FQXSPSS4003I: License key for [arg1] removed by user [arg2].
A user removes a License Key
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0097
User Action:
Information only; no action is required
FQXSPSS4004I: Test Call Home Generated by user [arg1].
Test Call Home generated by user.
- Severity: Info
- Serviceable: No
- Automatically notify Support: Yes
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0134
User Action:
Information only; no action is required
FQXSPSS4005I: Manual Call Home by user [arg1]: [arg2].
Manual Call Home by user.
- Severity: Info
- Serviceable: No
- Automatically notify Support: Yes
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0135
User Action:
Information only; no action is required
FQXSPSS4006I: Call Home to [arg1] failed to complete: [arg2].
Call Home failed to complete.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0195
User Action:
Information only; no action is required
FQXSPSS4007I: The BMC functionality tier is changed from [arg1] to [arg2].
Tier Change
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0222
User Action:
Information only; no action is required
FQXSPSS4008I: The [arg1] setting has been changed to [arg2] by user [arg3].
The setting has been changed by user
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0225
User Action:
Information only; no action is required
FQXSPSS4009I: System enters LXPM maintenance mode.
The system enters maintenance mode
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0226
User Action:
Information only; no action is required
FQXSPSS4010I: Test Audit Log generated by user [arg1].
This message is for the use case where OS Crash Video Capture Failed.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0237
User Action:
Information only; no action is required
FQXSPSS4011I: Fan speed boost setting is changed from [arg1] to [arg2].
The setting of fan speed boost is changed.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0254
User Action:
Information only; no action is required
FQXSPTR4000I: Management Controller [arg1] clock has been set from NTP server [arg2].
This message is for the use case where a Management Controller clock has been set from the Network Time Protocol server.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0033
User Action:
Information only; no action is required
FQXSPTR4001I: Date and Time set by user [arg1]: Date=[arg2], Time-[arg3], DST Auto-adjust=[arg4], Timezone=[arg5].
A user configured the Date and Time settings
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0079
User Action:
Information only; no action is required
FQXSPTR4002I: Synchronize time setting by user [arg1]: Mode=Sync with NTP Server, NTPServerHost1=[arg2]:[arg3],NTPServerHost2=[arg4]:[arg5],NTPServerHost3=[arg6]:[arg7],NTPServerHost4=[arg8]:[arg9],NTPUpdateFrequency=[arg10].
A user configured the Date and Time synchronize settings
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0085
User Action:
Information only; no action is required
FQXSPTR4003I: Synchronize time setting by user [arg1]: Mode=Sync with server clock.
A user configured the Date and Time synchronize settings
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0224
User Action:
Information only; no action is required
FQXSPUN0009G: Sensor [SensorElementName] has asserted.
This message is for the use case when an implementation has detected a Sensor has asserted.
- Severity: Warning
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: PLAT CIM ID: 0508
User Action:
Reboot the system. If the problem still exist, press F1 or use LXPM to do XCC FW update.
FQXSPUN0009I: Sensor [SensorElementName] has asserted.
This message is for the use case when an implementation has detected a Sensor has asserted.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: PLAT CIM ID: 0508
User Action:
Information only; no action is required.
FQXSPUN0017I: Sensor [SensorElementName] has transitioned to normal state.
This message is for the use case when an implementation has detected a Sensor transition to the normal state.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Warning - Other
- SNMP Trap ID: 60
- CIM Prefix: PLAT CIM ID: 0518
User Action:
Information only; no action is required
FQXSPUN0018J: Sensor [SensorElementName] has transitioned from normal to non-critical state.
This message is for the use case when an implementation has detected a Sensor transitioned to non-critical from normal.
- Severity: Warning
- Serviceable: Yes
- Automatically notify Support: No
- Alert Category: Warning - Other
- SNMP Trap ID: 60
- CIM Prefix: PLAT CIM ID: 0520
User Action:
Please check event log of xClarity Controller to investigate the identified device for enhancement.
FQXSPUN0019M: Sensor [SensorElementName] has transitioned to critical from a less severe state.
This message is for the use case when an implementation has detected a Sensor transitioned to critical from less severe.
- Severity: Error
- Serviceable: Yes
- Automatically notify Support: No
- Alert Category: Critical - Other
- SNMP Trap ID: 50
- CIM Prefix: PLAT CIM ID: 0522
User Action:
Complete the following steps until the problem is solved:- Please check XCC web GUI to see the identified error.
- Check system event log to fix the error.
- If the problem still exist, please contact local service.
FQXSPUN0020N: Sensor [SensorElementName] has transitioned to non-recoverable from a less severe state.
This message is for the use case when an implementation has detected a Sensor transitioned to non-recoverable from less severe.
- Severity: Error
- Serviceable: Yes
- Automatically notify Support: No
- Alert Category: Critical - Other
- SNMP Trap ID: 50
- CIM Prefix: PLAT CIM ID: 0524
User Action:
Complete the following steps:- Please flash uEFI image to the latest level.
- If the problem still exist, please remove and re-install CMOS battery for 30 seconds to clear CMOS contents.
- If the problem still exist, please contact local service.
FQXSPUN0023N: Sensor [SensorElementName] has transitioned to non-recoverable.
This message is for the use case when an implementation has detected a Sensor transitioned to non-recoverable.
- Severity: Error
- Serviceable: Yes
- Automatically notify Support: No
- Alert Category: Critical - Other
- SNMP Trap ID: 50
- CIM Prefix: PLAT CIM ID: 0530
User Action:
Complete the following steps:- Check the Lenovo support site for an applicable service bulletin or firmware update that applies to this error.
- Reboot the system.
- If problem persists, collect Service Data log and Contact Lenovo Support.
- For 1-2 Processor system:
- Reduce the compute board/system in error to a minimum configuration; 1 CPU + 1 DIMM. Does the problem still occur? Yes/No
- No: Add CPU and/DIMMs one and a time until the error re-occurs. Consider replacing the last CPU or DIMM that was installed that caused the error.
- Yes: If there error/problem still exists, swap in one of the other DIMMs and/or CPUs previously removed in step a. Proceed to add HW one piece at a time to identify the bad CPU or DIMM.
- If the problem still exist, (trained technician only) replace system board.
- If problem persists, escalate to next level of support.
- For 4-8 Processor system:
- Escalate to a next level of support.
FQXSPUN0026G: Device [LogicalDeviceElementName] has been added.
This message is for the use case when an implementation has detected a Device was inserted.
- Severity: Warning
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID:
- CIM Prefix: PLAT CIM ID: 0536
User Action:
Information only; no action is required
FQXSPUN0026I: Device [LogicalDeviceElementName] has been added.
This message is for the use case when an implementation has detected a Device was inserted.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID:
- CIM Prefix: PLAT CIM ID: 0536
User Action:
Information only; no action is required
FQXSPUN0027I: Device [LogicalDeviceElementName] has been removed from unit [PhysicalPackageElementName].
This message is for the use case when an implementation has detected a Device was removed.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID:
- CIM Prefix: PLAT CIM ID: 0537
User Action:
Information only; no action is required
FQXSPUN0047N: Sensor [SensorElementName] has transitioned to non-recoverable.
This message is for the use case when an implementation has detected a Sensor transitioned to non-recoverable.
- Severity: Error
- Serviceable: Yes
- Automatically notify Support: No
- Alert Category: Critical - Other
- SNMP Trap ID: 50
- CIM Prefix: PLAT CIM ID: 0530
User Action:
Complete the following steps:- Check the Lenovo support site for an applicable service bulletin or firmware update that applies to this error.
- Reboot the system.
- If problem persists, collect Service Data log and Contact Lenovo Support.
- For 1-2 Processor system:
- Reduce the compute board/system in error to a minimum configuration; 1 CPU + 1 DIMM. Does the problem still occur? Yes/No
- No: Add CPU and/DIMMs one and a time until the error re-occurs. Consider replacing the last CPU or DIMM that was installed that caused the error.
- Yes: If there error/problem still exists, swap in one of the other DIMMs and/or CPUs previously removed in step a. Proceed to add HW one piece at a time to identify the bad CPU or DIMM.
- If the problem still exist, (trained technician only) replace system board.
- If problem persists, escalate to next level of support.
- For 4-8 Processor system:
- Escalate to a next level of support.
FQXSPUN0056G: Sensor [SensorElementName] has asserted.
This message is for the use case when an implementation has detected a Sensor has asserted.
- Severity: Warning
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Warning - Other
- SNMP Trap ID: 60
- CIM Prefix: PLAT CIM ID: 0508
User Action:
Information only; no action is required
FQXSPUN0056I: Sensor [SensorElementName] has deasserted.
This message is for the use case when an implementation has detected a Sensor has deasserted.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Warning - Other
- SNMP Trap ID:
- CIM Prefix: PLAT CIM ID: 0509
User Action:
Information only; no action is required
FQXSPUN2009I: Sensor [SensorElementName] has deasserted.
This message is for the use case when an implementation has detected a Sensor has deasserted.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: PLAT CIM ID: 0509
User Action:
Information only; no action is required
FQXSPUN2010I: Sensor [SensorElementName] has asserted.
This message is for the use case when an implementation has detected a Sensor has asserted.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: PLAT CIM ID: 0508
User Action:
Reflash uEFI image. If error does not persist no additional recovery action is required.
FQXSPUN2012I: Sensor [SensorElementName] has deasserted.
This message is for the use case when an implementation has detected a Sensor has deasserted.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: PLAT CIM ID: 0509
User Action:
Information only; no action is required
FQXSPUN2018I: Sensor [SensorElementName] has deasserted the transition from normal to non-critical state.
This message is for the use case when an implementation has detected that a Sensor has deasserted a transition to non-critical from normal.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Warning - Other
- SNMP Trap ID: 60
- CIM Prefix: PLAT CIM ID: 0521
User Action:
Information only; no action is required
FQXSPUN2019I: Sensor [SensorElementName] has transitioned to a less severe state from critical.
This message is for the use case when an implementation has detected a Sensor transition to less severe from critical.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Critical - Other
- SNMP Trap ID: 50
- CIM Prefix: PLAT CIM ID: 0523
User Action:
Information only; no action is required
FQXSPUN2020I: Sensor [SensorElementName] has deasserted the transition to non-recoverable from a less severe state.
This message is for the use case when an implementation has detected that the Sensor transition to non-recoverable from less severe has deasserted.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Critical - Other
- SNMP Trap ID: 50
- CIM Prefix: PLAT CIM ID: 0525
User Action:
Information only; no action is required
FQXSPUN2023I: Sensor [SensorElementName] has deasserted the transition to non-recoverable.
This message is for the use case when an implementation has detected that the Sensor transition to non-recoverable has deasserted.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: Critical - Other
- SNMP Trap ID: 50
- CIM Prefix: PLAT CIM ID: 0531
User Action:
Information only; no action is required
FQXSPUN2030I: Device [LogicalDeviceElementName] has been removed from unit [PhysicalPackageElementName].
This message is for the use case when an implementation has detected a Device was removed.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID:
- CIM Prefix: PLAT CIM ID: 0537
User Action:
Information only; no action is required
FQXSPUP0007L: Invalid or Unsupported firmware or software was detected on system [ComputerSystemElementName].
This message is for the use case when an implementation has detected an Invalid/Unsupported Firmware/Software Version.
- Severity: Error
- Serviceable: Yes
- Automatically notify Support: No
- Alert Category: Critical - Other
- SNMP Trap ID: 50
- CIM Prefix: PLAT CIM ID: 0446
User Action:
Reflash or update XCC firmware
FQXSPUP4000I: Please ensure that the Management Controller [arg1] is flashed with the correct firmware. The Management Controller is unable to match its firmware to the server.
This message is for the use case where a Management Controller firmware version does not match the server.
- Severity: Error
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0031
User Action:
Update the XCC firmware to a version that the server supports. Important: Some cluster solutions require specific code levels or coordinated code updates. If the device is part of a cluster solution, verify that the latest level of code is supported for the cluster solution before you update the code.
FQXSPUP4001I: Flash of [arg1] from [arg2] succeeded for user [arg3] .
This message is for the use case where a user has successfully flashed the firmware component (MC Main Application, MC Boot ROM, BIOS, Diagnostics, System Power Backplane, Remote Expansion Enclosure Power Backplane, Integrated System Management).
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0035
User Action:
Information only; no action is required
FQXSPUP4002I: Flash of [arg1] from [arg2] failed for user [arg3].
This message is for the use case where a user has not flashed the firmware component from the interface and IP address due to a failure.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0036
User Action:
Information only; no action is required
FQXSPUP4003I: [arg1] firmware mismatch internal to system [arg2]. Please attempt to flash the [arg3] firmware.
This message is for the use case where a specific type of firmware mismatch has been detected.
- Severity: Error
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0042
User Action:
Reflash the XCC firmware to the latest version.
FQXSPUP4004I: XCC firmware mismatch between nodes/servers [arg1] and [arg2]. Please attempt to flash the XCC firmware to the same level on all nodes/servers.
A mismatch of XCC firmware has been detected between nodes/servers
- Severity: Error
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0132
User Action:
Attempt to flash the XCC firmware to the same level on all nodes.
FQXSPUP4005I: FPGA firmware mismatch between nodes/servers [arg1] and [arg2]. Please attempt to flash the FPGA firmware to the same level on all nodes/servers.
A mismatch of FPGA firmware has been detected between nodes/servers
- Severity: Error
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0133
User Action:
Attempt to flash the FPGA firmware to the same level on all nodes.
FQXSPUP4006I: Auto promote primary XCC to backup is [arg1] by user [arg2] from [arg3] at IP address [arg4].
Auto promote primary XCC to backup is enabled or disabled.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0281
User Action:
Information only; no action is required
FQXSPUP4007I: Violation access to XCC SPI flash is detected and isolated.
This message is for the use case where violation access to XCC SPI flash is detected and isolated.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0298
User Action:
Information only; no action is required
FQXSPUP4008I: Violation access to UEFI SPI flash is detected and isolated.
This message is for the use case where violation access to UEFI SPI flash is detected and isolated.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0299
User Action:
Information only; no action is required
FQXSPUP4009I: Please ensure that the system is flashed with the correct [arg1] firmware. The Management Controller is unable to match the firmware to the server.
This message is for the use case where a firmware version does not match the server.
- Severity: Error
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0324
User Action:
Information only; no action is required
FQXSPUP4010I: Flash [arg1] of [arg2] from [arg3] succeeded for user [arg4] .
This message is for the use case where a user has successfully flashed the firmware component (MC Main Application, MC Boot ROM, BIOS, Diagnostics, System Power Backplane, Remote Expansion Enclosure Power Backplane, Integrated System Management).
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0325
User Action:
Information only; no action is required
FQXSPUP4011I: Flash [arg1] of [arg2] from [arg3] failed for user [arg4].
This message is for the use case where a user has not flashed the firmware component from the interface and IP address due to a failure.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: IMM CIM ID: 0326
User Action:
Information only; no action is required
FQXSPWD0000I: Watchdog Timer expired for [WatchdogElementName].
This message is for the use case when an implementation has detected a Watchdog Timer Expired.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: PLAT CIM ID: 0368
User Action:
Information only; no action is required
FQXSPWD0001I: Reboot of system [ComputerSystemElementName] initiated by watchdog [WatchdogElementName].
This message is for the use case when an implementation has detected a Reboot by a Watchdog occurred.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: PLAT CIM ID: 0370
User Action:
Information only; no action is required
FQXSPWD0002I: Powering off system [ComputerSystemElementName] initiated by watchdog [WatchdogElementName].
This message is for the use case when an implementation has detected a Poweroff by Watchdog has occurred.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: PLAT CIM ID: 0372
User Action:
Information only; no action is required
FQXSPWD0003I: Power cycle of system [ComputerSystemElementName] initiated by watchdog [WatchdogElementName].
This message is for the use case when an implementation has detected a Power Cycle by Watchdog occurred.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: PLAT CIM ID: 0374
User Action:
Information only; no action is required
FQXSPWD0004I: Watchdog Timer interrupt occurred for [WatchdogElementName].
This message is for the use case when an implementation has detected a Watchdog Timer interrupt occurred.
- Severity: Info
- Serviceable: No
- Automatically notify Support: No
- Alert Category: System - Other
- SNMP Trap ID: 22
- CIM Prefix: PLAT CIM ID: 0376
User Action:
Information only; no action is required