Skip to main content

XCC events organized by severity

The following table lists all XCC events, organized by severity (Information, Error, and Warning).

Table 1. Events organized by severity
Event IDMessage StringSeverity
FQXSPBR4000IManagement Controller [arg1]: Configuration restored from a file by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPBR4002IManagement Controller [arg1] Reset was caused by restoring default values.Informational
FQXSPBR4004IServer timeouts set by user [arg1]: EnableOSWatchdog=[arg2], OSWatchdogTimout=[arg3], EnableLoaderWatchdog=[arg4], LoaderTimeout=[arg5] from [arg6] at IP address [arg7].Informational
FQXSPBR4005IManagement Controller [arg1]: Configuration saved to a file by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPBR4006IManagement Controller [arg1]: Configuration restoration from a file by user [arg2] completed from [arg3] at IP address [arg4].Informational
FQXSPBR4009IManagement Controller [arg1]: cloning configuration from neighbor server [arg2] by group name [arg3].Informational
FQXSPBR400AIManagement Controller [arg1]: cloning configuration from neighbor server [arg2] by group name [arg3] completed.Informational
FQXSPBR400BIManagement Controller [arg1]: cloning configuration from neighbor server [arg2] by group name [arg3] failed to complete.Informational
FQXSPBR400CIManagement Controller [arg1]: cloning configuration from neighbor server [arg2] by group name [arg3] failed to start.Informational
FQXSPBR400DINeighbor group clone configuration was initiated by user [arg1] from [arg2] at IP address [arg3].Informational
FQXSPBR400EINeighbor group firmware update was initiated by user [arg1] from [arg2] at IP address [arg3].Informational
FQXSPBR400FIThe neighbor group management is [arg1] by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPCA0012IFan mismatch is recovered.Informational
FQXSPCA0013IPCIe [SensorName] overtemperature has transitioned to normal state.Informational
FQXSPCA2000IFan [NumericSensorName] going low (lower non-critical) has deasserted.Informational
FQXSPCA2002IFan [NumericSensorName] going low (lower critical) has deasserted.Informational
FQXSPCA2007IAmbient temperature going high (upper non-critical) has deasserted.Informational
FQXSPCA2009IAmbient temperature going high (upper critical) has deasserted.Informational
FQXSPCA2011IAmbient temperature going high (upper non-recoverable) has deasserted.Informational
FQXSPCA2016IFan Mismatch has transitioned to a less severe state from critical.Informational
FQXSPCA2017IPCIe [SensorName] overtemperature has transitioned to a less severe state from critical.Informational
FQXSPCA2019IPCIe [SensorName] overtemperature has deasserted the transition to non-recoverable from a less severe state.Informational
FQXSPCA2042ILiquid leak detector for [DeviceType] is recovered.Informational
FQXSPCA2046IDIMM [DIMMId] temperature going high (upper non-critical) has deasserted.Informational
FQXSPCA2047IDIMM [DIMMId] temperature going high (upper critical) has deasserted.Informational
FQXSPCA2048IDIMM [DIMMId] temperature going high (upper non-recoverable) has deasserted.Informational
FQXSPCA2049IPump tach [pumpFanIndex] going high (upper non-critical) has deasserted.Informational
FQXSPCA2050IPump tach [pumpFanIndex] going high (upper critical) has deasserted.Informational
FQXSPCA2051IPump tach [pumpFanIndex] going high (upper non-recoverable) has deasserted.Informational
FQXSPCA2052IPump tach [pumpFanIndex] going low (lower critical) has deasserted.Informational
FQXSPCN4000ISerial Redirection set by user [arg1]: Mode=[arg2], BaudRate=[arg3], StopBits=[arg4], Parity=[arg5], SessionTerminateSequence=[arg6] from [arg7] at IP address [arg8].Informational
FQXSPCN4002IUser [arg1] has terminated an active CLI console session from [arg2] at IP address [arg3].Informational
FQXSPCN4004IUser [arg1] has created an active [arg2] console session from [arg3] at IP address [arg4].Informational
FQXSPCN4005IA [arg1] console session is timeout.Informational
FQXSPCN4006IUser [arg1] has terminated an active IPMI console session from [arg2] at IP address [arg3].Informational
FQXSPCP2001IDevice [DeviceName] has deasserted from a configuration mismatch.Informational
FQXSPDM4000IInventory data changed for device [arg1], new device data hash=[arg2], new master data hash=[arg3].Informational
FQXSPDM4003ITKLM servers set by user [arg1]: TKLMServer1=[arg2] Port=[arg3], TKLMServer2=[arg4] Port=[arg5], TKLMServer3=[arg6] Port=[arg7], TKLMServer4=[arg8] Port=[arg9] from [arg10] at IP address [arg11].Informational
FQXSPDM4004ITKLM servers device group set by user [arg1]: TKLMServerDeviceGroup=[arg2] from [arg3] at IP address [arg4].Informational
FQXSPDM4005IUser [arg1] has generated a new encryption key pair and installed a self-signed certificate for the TKLM client from [arg2] at IP address [arg3].Informational
FQXSPDM4006IUser [arg1] has generated a new encryption key and certificate signing request for the TKLM client from [arg2] at IP address [arg3].Informational
FQXSPDM4007IUser [arg1] has imported a signed certificate for the TKLM client from [arg2] from [arg3] at IP address [arg4].Informational
FQXSPDM4008IUser [arg1] has imported a server certificate for the TKLM server from [arg2] at IP address [arg3].Informational
FQXSPDM4009IUser [arg1] has [arg2] file [arg3] from [arg4] at IP address [arg5].Informational
FQXSPDM4010IInventory data collecting and processing complete for [arg1], sequence number is [arg2].Informational
FQXSPDM4011IEKMS server protocol set by user [arg1]: TKLMServerProtocol=[arg2] from [arg3] at IP address [arg4].Informational
FQXSPDM4012IUser [arg1] has changed the polling configuration for the key management server: Polling enabled=[arg2], interval=[arg3].Informational
FQXSPDM4013IUser [arg1] has changed the caching configuration for the key management server: Caching enabled=[arg2], timeout=[arg3].Informational
FQXSPEA2003ILink up is detected on port [[1]] of the PCIe device [[2]] in slot [[3]].Informational
FQXSPEM0003IThe Log [RecordLogName] has been cleared.Informational
FQXSPEM0004IThe Log [RecordLogName] is full.Informational
FQXSPEM0005IThe Log [RecordLogName] is almost full.Informational
FQXSPEM2004IThe Log [RecordLogName] is no longer full.Informational
FQXSPEM4000IThe [arg1] on system [arg2] cleared by user [arg3] from [arg4] at IP address [arg5].Informational
FQXSPEM4003ILED [arg1] state changed to [arg2] by [arg3] from [arg4] at IP address [arg5].Informational
FQXSPEM4004ISNMP [arg1] enabled by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPEM4005ISNMP [arg1] disabled by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPEM4006IAlert Configuration Global Event Notification set by user [arg1]: RetryLimit=[arg2], RetryInterval=[arg3], EntryInterval=[arg4] from [arg5] at IP address [arg6].Informational
FQXSPEM4007IAlert Recipient Number [arg1] by syslog is updated: Name=[arg2], DeliveryMethod=[arg3], Address=[arg4], IncludeLog=[arg5], Enabled=[arg6], EnabledAlerts=-crt<[arg7]> -wrn<[arg8]> -sys<[arg9]> by user [arg10] from [arg11] at IP address [arg12].Informational
FQXSPEM4008ISNMP Traps enabled by user [arg1]: EnabledAlerts=-crt<[arg2]> -wrn<[arg3]> -sys<[arg4]> from [arg5] at IP address [arg6].Informational
FQXSPEM4009IThe UEFI Definitions have been changed.Informational
FQXSPEM4011IXCC failed to log previous event [arg1].Informational
FQXSPEM4012IUser [arg1] made system [arg2] Encapsulation lite Mode from [arg3] at IP address [arg4].Informational
FQXSPEM4028IThe port [arg1] of PCIe device [arg2] has link [arg3].Informational
FQXSPEM4031ISSD wear [arg1] threshold setting is changed from [arg2] to [arg3] by user [arg4] from [arg5] at IP address [arg6].Informational
FQXSPEM4041IThe SmartNIC in slot [arg1] encountered boot timeout.Informational
FQXSPEM4042IThe SmartNIC in slot [arg1] went through a crash dump.Informational
FQXSPEM4046IAlert Recipient Number [arg1] by email is updated: Name=[arg2], DeliveryMethod=[arg3], EmailAddress=[arg4], IncludeLog=[arg5], Enabled=[arg6], EnabledAlerts=-crt<[arg7]> -wrn<[arg8]> -sys<[arg9]> by user [arg10] from [arg11] at IP address [arg12].Informational
FQXSPEM4047ILED [arg1] state changed to [arg2] with physical button.Informational
FQXSPFC4000IThe bare metal connection process has been started.Informational
FQXSPFC4001IThe bare metal update application reports a status of [arg1].Informational
FQXSPFW0003IThe System [ComputerSystemName] encountered firmware progress.Informational
FQXSPFW0004IUEFI advanced memory test is running.Informational
FQXSPFW0005IUEFI advanced memory test is completed.Informational
FQXSPFW0006IUEFI advanced memory test is interrupted.Informational
FQXSPFW0007IUEFI advanced memory test encountered a hang.Informational
FQXSPFW2001IThe System [ComputerSystemName] has detected a POST Error deassertion - firmware(BIOS) ROM corruption detected.Informational
FQXSPIO0000IThe connector [PhysicalConnectorName] has been detected as present or connected.Informational
FQXSPIO0005NAn I/O Channel Check NMI has occurred on system [ComputerSystemName].Informational
FQXSPIO0010IA Correctable Bus Error has occurred on bus [BusName].Informational
FQXSPIO0032IDevice [DeviceType] [DeviceIndex] is installed.Informational
FQXSPIO0033IDevice [DeviceType] [DeviceIndex] is uninstalled.Informational
FQXSPIO0034IConnector [ConnectorName] is linked to [DeviceType] [DeviceIndex].Informational
FQXSPIO2004IBus [BusName] has recovered from a bus timeout.Informational
FQXSPIO2005ISystem [ComputerSystemName] has recovered from I/O Channel Check NMI.Informational
FQXSPIO2006ISystem [ComputerSystemName] has recovered from software NMI.Informational
FQXSPIO2010IBus [BusName] has recovered from a Correctable Bus Error.Informational
FQXSPIO2011IPCIs has recovered from an Uncorrectable Error.Informational
FQXSPIO2013IBus [BusName] has recovered from a Fatal Bus Error.Informational
FQXSPIO2014IBus [BusName] is no longer operating in a degraded state.Informational
FQXSPMA0025IBMC LAN failover from dedicate to shared.Informational
FQXSPMA2010IDIMM [DIMMId] on system [MemoryName] is no longer throttled.Informational
FQXSPMA2012IAn Over-Temperature Condition has been removed on the dimm [DIMMId] on system [MemoryName].Informational
FQXSPMA2025IBMC LAN recovers back from shared to dedicate.Informational
FQXSPMA2037IDIMMs has recovered from an Uncorrectable Error.Informational
FQXSPMA2039IDIMM [DIMMID] is enabled.Informational
FQXSPNM4000IManagement Controller [arg1] Network Initialization Complete.Informational
FQXSPNM4001IEthernet Data Rate modified from [arg1] to [arg2] by user [arg3] from [arg4] at IP address [arg5].Informational
FQXSPNM4002IEthernet Duplex setting modified from [arg1] to [arg2] by user [arg3] from [arg4] at IP address [arg5].Informational
FQXSPNM4003IEthernet MTU setting modified from [arg1] to [arg2] by user [arg3] from [arg4] at IP address [arg5].Informational
FQXSPNM4004IEthernet locally administered MAC address modified from [arg1] to [arg2] by user [arg3] from [arg4] at IP address [arg5].Informational
FQXSPNM4005IEthernet interface [arg1] by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPNM4006IHostname set to [arg1] by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPNM4011IENET[[arg1]] DHCP-HSTN=[arg2], DN=[arg3], IP@=[arg4], SN=[arg5], GW@=[arg6], DNS1@=[arg7].Informational
FQXSPNM4012IENET[[arg1]] IP-Cfg:HstName=[arg2], IP@=[arg3] ,NetMsk=[arg4], GW@=[arg5].Informational
FQXSPNM4013ILAN: Ethernet[[arg1]] interface is no longer active.Informational
FQXSPNM4014ILAN: Ethernet[[arg1]] interface is now active.Informational
FQXSPNM4016IDomain name set to [arg1] by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPNM4017IDomain Source changed to [arg1] by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPNM4018IDDNS setting changed to [arg1] by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPNM4019IDDNS registration successful. The domain name is [arg1].Informational
FQXSPNM4020IIPv6 enabled by user [arg1] from [arg2] at IP address [arg3].Informational
FQXSPNM4021IIPv6 disabled by user [arg1] from [arg2] at IP address [arg3].Informational
FQXSPNM4022IIPv6 static IP configuration enabled by user [arg1] from [arg2] at IP address [arg3].Informational
FQXSPNM4023IIPv6 DHCP enabled by user [arg1] from [arg2] at IP address [arg3].Informational
FQXSPNM4024IIPv6 stateless auto-configuration enabled by user [arg1] from [arg2] at IP address [arg3].Informational
FQXSPNM4025IIPv6 static IP configuration disabled by user [arg1] from [arg2] at IP address [arg3].Informational
FQXSPNM4026IIPv6 DHCP disabled by user [arg1] from [arg2] at IP address [arg3].Informational
FQXSPNM4027IIPv6 stateless auto-configuration disabled by user [arg1] from [arg2] at IP address [arg3].Informational
FQXSPNM4028IENET[[arg1]] IPv6-LinkLocal:HstName=[arg2], IP@=[arg3] ,Pref=[arg4].Informational
FQXSPNM4029IENET[[arg1]] IPv6-Static:HstName=[arg2], IP@=[arg3] ,Pref=[arg4], GW@=[arg5].Informational
FQXSPNM4030IENET[[arg1]] DHCPv6-HSTN=[arg2], DN=[arg3], IP@=[arg4], Pref=[arg5], DNS1@=[arg6].Informational
FQXSPNM4031IIPv6 static address of network interface modified from [arg1] to [arg2] by user [arg3] from [arg4] at IP address [arg5].Informational
FQXSPNM4034ISSH port number changed from [arg1] to [arg2] by user [arg3] from [arg4] at IP address [arg5].Informational
FQXSPNM4035IWeb-HTTP port number changed from [arg1] to [arg2] by user [arg3] from [arg4] at IP address [arg5].Informational
FQXSPNM4036IWeb-HTTPS port number changed from [arg1] to [arg2] by user [arg3] from [arg4] at IP address [arg5].Informational
FQXSPNM4039ISNMP Agent port number changed from [arg1] to [arg2] by user [arg3] from [arg4] at IP address [arg5].Informational
FQXSPNM4040ISNMP Traps port number changed from [arg1] to [arg2] by user [arg3] from [arg4] at IP address [arg5].Informational
FQXSPNM4041ISyslog port number for syslog receiver [arg1] is changed from [arg2] to [arg3] by user [arg4] from [arg5] at IP address [arg6].Informational
FQXSPNM4042IRemote Presence port number changed from [arg1] to [arg2] by user [arg3] from [arg4] at IP address [arg5].Informational
FQXSPNM4043ISMTP Server set by user [arg1] to [arg2]:[arg3] from [arg4] at IP address [arg5].Informational
FQXSPNM4045IDNS servers set by user [arg1]: UseAdditionalServers=[arg2], PreferredDNStype=[arg3], IPv4Server1=[arg4], IPv4Server2=[arg5], IPv4Server3=[arg6], IPv6Server1=[arg7], IPv6Server2=[arg8], IPv6Server3=[arg9] from [arg10] at IP address [arg11].Informational
FQXSPNM4046ILAN over USB [arg1] by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPNM4047ILAN over USB Port Forwarding set by user [arg1]: ExternalPort=[arg2], USB-LAN port=[arg3] from [arg4] at IP address [arg5].Informational
FQXSPNM4048IPXE boot requested by user [arg1] from [arg2] at IP address [arg3].Informational
FQXSPNM4049IUser [arg1] has initiated a TKLM Server Connection Test to check connectivity to server [arg2] from [arg3] at IP address [arg4].Informational
FQXSPNM4051IUser [arg1] has set the SMTP Server reverse-path to [arg2] from [arg3] at IP address [arg4].Informational
FQXSPNM4053IDNS discovery of Lenovo XClarity Administrator has been [arg1] by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPNM4054IThe hostname from DHCP is [arg1] by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPNM4055IThe hostname from DHCP is invalid.Informational
FQXSPNM4056IThe NTP server address [arg1] is invalid.Informational
FQXSPNM4057ISecurity: IP address: [arg1] had [arg2] login failures, it will be blocked to access for [arg3] minutes.Informational
FQXSPNM4058IIP address of network interface [arg1] is modified from [arg2] to [arg3] by user [arg4] from [arg5] at IP address [arg6].Informational
FQXSPNM4059IIP subnet mask of network interface [arg1] is modified from [arg2] to [arg3] by user [arg4] from [arg5] at IP address [arg6].Informational
FQXSPNM4060IIP address of default gateway of network interface [arg1] is modified from [arg2] to [arg3] by user [arg4] from [arg5] at IP address [arg6].Informational
FQXSPNM4068IThe USB [arg1] is [arg2] by user [arg3] from [arg4] at IP address [arg5].Informational
FQXSPNM4069IThe LLDP service is [arg1] by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPNM4070IUplinkMac is [arg1] by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPOS4000IOS Watchdog response [arg1] by [arg2] from [arg3] at IP address [arg4].Informational
FQXSPOS4001IWatchdog [arg1] Screen Capture Occurred.Informational
FQXSPOS4004IOperating System status has changed to [arg1].Informational
FQXSPOS4005IHost Power-On password changed by user [arg1] from [arg2] at IP address [arg3].Informational
FQXSPOS4006IHost Power-On password cleared by user [arg1] from [arg2] at IP address [arg3].Informational
FQXSPOS4007IHost Admin password changed by user [arg1] from [arg2] at IP address [arg3].Informational
FQXSPOS4008IHost Admin password cleared by user [arg1] from [arg2] at IP address [arg3].Informational
FQXSPOS4009IOS Crash Video Captured.Informational
FQXSPOS4011IOS failure screen capture with hardware error is [arg1] by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPOS4012IPOST watchdog Screen Capture Occurred.Informational
FQXSPPP4000IAttempting to [arg1] server [arg2] by user [arg3] from [arg4] at IP address [arg5].Informational
FQXSPPP4001IServer Power Off Delay set to [arg1] by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPPP4002IServer [arg1] scheduled for [arg2] at [arg3] by user [arg4] from [arg5] at IP address [arg6].Informational
FQXSPPP4003IServer [arg1] scheduled for every [arg2] at [arg3] by user [arg4] from [arg5] at IP address [arg6].Informational
FQXSPPP4004IServer [arg1] [arg2] cleared by user [arg3] from [arg4] at IP address [arg5].Informational
FQXSPPP4005IThe power cap value changed from [arg1] watts to [arg2] watts by user [arg3] from [arg4] at IP address [arg5].Informational
FQXSPPP4011IPower capping was activated by user [arg1] from [arg2] at IP address [arg3].Informational
FQXSPPP4012IPower capping was deactivated by user [arg1] from [arg2] at IP address [arg3].Informational
FQXSPPP4020IThe measured power value has returned below the power cap value.Informational
FQXSPPP4022IThe server was restarted for an unknown reason.Informational
FQXSPPP4023IThe server is restarted by chassis control command.Informational
FQXSPPP4024IThe server was reset via push button.Informational
FQXSPPP4025IThe server was powered-up via power push button.Informational
FQXSPPP4026IThe server was restarted when the watchdog expired.Informational
FQXSPPP4027IThe server was restarted for OEM reason.Informational
FQXSPPP4028IThe server was automatically powered on because the power restore policy is set to always on.Informational
FQXSPPP4029IThe server was automatically powered on because the power restore policy is set to restore previous power state.Informational
FQXSPPP4030IThe server was reset via Platform Event Filter.Informational
FQXSPPP4031IThe server was power-cycled via Platform Event Filter.Informational
FQXSPPP4032IThe server was soft reset.Informational
FQXSPPP4033IThe server was powered up via Real Time Clock (scheduled power on).Informational
FQXSPPP4034IThe server was powered off for an unknown reason.Informational
FQXSPPP4035IThe server was powered off by chassis control command.Informational
FQXSPPP4036IThe server was powered off via push button.Informational
FQXSPPP4037IThe server was powered off when the watchdog expired.Informational
FQXSPPP4038IThe server stayed powered off because the power restore policy is set to always off.Informational
FQXSPPP4039IThe server stayed powered off because the power restore policy is set to restore previous power state.Informational
FQXSPPP4040IThe server was powered off via Platform Event Filter.Informational
FQXSPPP4041IThe server was powered off via Real Time Clock (scheduled power off).Informational
FQXSPPP4042IManagement Controller [arg1] reset was initiated due to Power-On-Reset.Informational
FQXSPPP4044IManagement Controller [arg1] reset was initiated by CMM.Informational
FQXSPPP4047IManagement Controller [arg1] reset was initiated by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPPP4048IAttempting to AC power cycle server [arg1] by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPPP4049IManagement Controller [arg1] reset was initiated by Front Panel.Informational
FQXSPPP4050IManagement Controller [arg1] reset was initiated to activate PFR Firmware.Informational
FQXSPPP4054IUnbalanced PSU config is detected, system is using less node PSU capacity.Informational
FQXSPPP4055IAttempting to [arg1] server [arg2] from [arg3].Informational
FQXSPPP4056IManagement Controller [arg1] reset was initiated to activate FPGA Firmware.Informational
FQXSPPP4057IAttempting to [arg1] from Diagnostic Handset.Informational
FQXSPPR0000I[BackplaneName] detected as present.Informational
FQXSPPR0003IFront Panel detected as present.Informational
FQXSPPR0004ITPM module detected as present.Informational
FQXSPPR2001I[BackplaneName] detected as absent.Informational
FQXSPPR2003IFront Panel detected as absent.Informational
FQXSPPR2004ITPM module detected as absent.Informational
FQXSPPU2001IAn Over-Temperature Condition has been removed on Processor [ProcessorId].Informational
FQXSPPU2002IThe Processor [ProcessorId] is no longer operating in a Degraded State.Informational
FQXSPPU2007IThe System [ComputerSystemName] has detected a POST Error deassertion - CPU voltage mismatch.Informational
FQXSPPU2009IProcessor [ProcessorId] has Recovered from a Configuration Mismatch.Informational
FQXSPPU2015ICPU feature mismatch is recovered.Informational
FQXSPPU2016ICPUs has recovered from an Uncorrectable Error.Informational
FQXSPPU2017IProcessor [ProcessorId] has recovered from a hard fault.Informational
FQXSPPW0001IPower supply [PowerSupplyId] has been added.Informational
FQXSPPW0002IPower supply [PowerSupplyId] in the enclosure/chassis (MTM-S/N: [MachineSerialNumber]) has been added.Informational
FQXSPPW0004IThe input to power supply [PowerSupplyId] has been lost or fallen out of range.Informational
FQXSPPW0005IPower supply [PowerSupplyId] is operating in an Input State that is out of range.Informational
FQXSPPW0008IHost power has been turned off.Informational
FQXSPPW0009IHost power has been Power Cycled.Informational
FQXSPPW0011IHost power has lost power.Informational
FQXSPPW0054IPSU Mismatch has transitioned to normal state.Informational
FQXSPPW0091IRedundancy Power Resource has been restored.Informational
FQXSPPW0129IPSU [SensorName] failure has transitioned to normal state.Informational
FQXSPPW0130IPSU [SensorName] prediction fault failure has transitioned to normal state.Informational
FQXSPPW0131IPSU [SensorName] input failure has transitioned to normal state.Informational
FQXSPPW2001IPower supply [PowerSupplyId] has been removed.Informational
FQXSPPW2002IPower supply [PowerSupplyId] has returned to OK status.Informational
FQXSPPW2003IFailure no longer predicted on power supply [PowerSupplyId].Informational
FQXSPPW2004IPower supply [PowerSupplyId] has returned to a Normal Input State.Informational
FQXSPPW2005IPower supply [PowerSupplyId] has returned to a Normal Input State.Informational
FQXSPPW2006IPower supply [PowerSupplyId] has returned to a Normal Input State.Informational
FQXSPPW2007IPower supply [PowerSupplyId] Configuration is OK.Informational
FQXSPPW2008IHost power has been turned on.Informational
FQXSPPW2009IPower supply [PowerSupplyId] in the enclosure/chassis (MTM-S/N: [MachineSerialNumber]) has been removed.Informational
FQXSPPW2011IHost power was restored.Informational
FQXSPPW2015IPower supply [PowerSupplyId] in the enclosure/chassis (MTM-S/N: [MachineSerialNumber]) has returned to OK status.Informational
FQXSPPW2017IPower supply [PowerSupplyId] in the enclosure/chassis (MTM-S/N: [MachineSerialNumber]) has returned to a normal input state.Informational
FQXSPPW2031ICMOS battery voltage going low (lower non-critical) has deasserted.Informational
FQXSPPW2057IPSU [SensorName] prediction fault failure has deasserted the transition from normal to non-critical state.Informational
FQXSPPW2061IPSU [SensorName] failure has transitioned to a less severe state from critical.Informational
FQXSPPW2062IPSU Mismatch has transitioned to a less severe state from critical.Informational
FQXSPPW2063ISysBrd voltage fault has transitioned to a less severe state from critical.Informational
FQXSPPW2101IRedundancy Degraded for Power Resource has deasserted.Informational
FQXSPPW2104INon-redundant:Sufficient Resources from Redundancy Degraded or Fully Redundant for Power Resource has deasserted.Informational
FQXSPPW2110INon-redundant:Insufficient Resources for Power Resource has deasserted.Informational
FQXSPPW2123IPSU [SensorName] input failure has transitioned to a less severe state from critical.Informational
FQXSPPW2134ICMOS battery voltage going low (lower critical) has deasserted.Informational
FQXSPPW2135IRecovered from invalid PSU redundancy config.Informational
FQXSPSD0000IThe [DriveName] has been added.Informational
FQXSPSD0003IHot Spare enabled with drive [DriveLocation].Informational
FQXSPSD0005IHot Spare enabled for drive [DriveLocation] in the enclosure/chassis (MTM-S/N: [MachineSerialNumber]).Informational
FQXSPSD0007IThe [DriveName] is rebuilding.Informational
FQXSPSD0008IArray rebuild in progress on drive [DriveLocation] in the enclosure/chassis (MTM-S/N: [MachineSerialNumber]).Informational
FQXSPSD2000IThe [DriveName] has been removed from unit [PhysicalPackageName].Informational
FQXSPSD2001IThe [DriveName] has recovered from a fault.Informational
FQXSPSD2002IFailure no longer Predicted on [DriveName].Informational
FQXSPSD2003IHot Spare disabled with drive [DriveLocation].Informational
FQXSPSD2007IRebuild completed on [DriveName].Informational
FQXSPSD2008IDrive [DriveLocation] in the enclosure/chassis (MTM-S/N: [MachineSerialNumber]) has recovered from a fault.Informational
FQXSPSD2011IFailure no longer predicted on drive [DriveLocation] in the enclosure/chassis (MTM-S/N: [MachineSerialNumber]).Informational
FQXSPSD2012IHot Spare disabled for drive [DriveLocation] in the enclosure/chassis (MTM-S/N: [MachineSerialNumber]).Informational
FQXSPSD2015IArray rebuild completed on drive [DriveLocation] in the enclosure/chassis (MTM-S/N: [MachineSerialNumber]).Informational
FQXSPSE2000IThe Chassis [ComputerSystemName] was closed.Informational
FQXSPSE2010ISystem guard changed to compliant status.Informational
FQXSPSE4001IRemote Login Successful. Login ID: [arg1] using [arg2] from [arg3] at IP address [arg4].Informational
FQXSPSE4002ISecurity: Userid: [arg1] using [arg2] had [arg3] login failures from WEB client at IP address [arg4].Informational
FQXSPSE4003ISecurity: Login ID: [arg1] had [arg2] login failures from CLI at [arg3].Informational
FQXSPSE4004IRemote access attempt failed. Invalid userid or password received. Userid is [arg1] from WEB browser at IP address [arg2].Informational
FQXSPSE4007ISecurity: Userid: [arg1] using [arg2] had [arg3] login failures from an SSH client at IP address [arg4].Informational
FQXSPSE4008ISNMPv1 [arg1] set by user [arg2]: Name=[arg3], AccessType=[arg4], Address=[arg5] from [arg6] at IP address [arg7].Informational
FQXSPSE4009ILDAP Server configuration set by user [arg1]: AuthenticatonOnly=[arg2], UseDNS=[arg3], ForestName=[arg4], DomainName=[arg5], Server1=[arg6], Server2=[arg7], Server3=[arg8], Server4=[arg9] from [arg10] at IP address [arg11].Informational
FQXSPSE4010ILDAP set by user [arg1]: Type=[arg2], RootDN=[arg3], UserSearchAttribute=[arg4], BindingMethod=[arg5], GroupFilter=[arg6], GroupSearchAttribute=[arg7], LoginAttribute=[arg8] from [arg9] at IP address [arg10].Informational
FQXSPSE4011ISecure Web services (HTTPS) [arg1] by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPSE4013ISecure LDAP [arg1] by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPSE4014ISSH [arg1] by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPSE4015IGlobal Login General Settings set by user [arg1]: AuthenticationMethod=[arg2], LockoutPeriod=[arg3], SessionTimeout=[arg4] from [arg5] at IP address [arg6].Informational
FQXSPSE4016IGlobal Login Account Security set by user [arg1]: ForceToChangePasswordOnFirstAccess=[arg2], ComplexPasswordRequired=[arg3], PasswordExpirationPeriod=[arg4], MinimumPasswordReuseCycle=[arg5], MinimumPasswordLength=[arg6], MinimumPasswordChangeInterval=[arg7], MaxmumLoginFailures=[arg8], LockoutAfterMaxFailures=[arg9] from [arg10] at IP address [arg11].Informational
FQXSPSE4022IUser [arg1] for SNMPv3 agent set: AuthenticationProtocol=[arg2], PrivacyProtocol=[arg3], AccessType=[arg4] by user [arg5] from [arg6] at IP address [arg7].Informational
FQXSPSE4023ISSH Client key added for user [arg1] by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPSE4024ISSH Client key imported for user [arg1] from [arg2] by user [arg3] from [arg4] at IP address [arg5].Informational
FQXSPSE4025ISSH Client key removed from user [arg1] by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPSE4028ISecurity: Userid: [arg1] had [arg2] login failures from IPMI client at IP address [arg3].Informational
FQXSPSE4029ISecurity: Userid: [arg1] had [arg2] login failures from SNMP client at IP address [arg3].Informational
FQXSPSE4032ILogin ID: [arg1] from [arg2] at IP address [arg3] has logged off.Informational
FQXSPSE4034IUser [arg1] has removed a certificate from [arg2] at IP address [arg3].Informational
FQXSPSE4035IA certificate has been revoked.Informational
FQXSPSE4036IThe [arg1] certificate is expired and has been removed.Informational
FQXSPSE4038IMinimum TLS level modified from [arg1] to [arg2] by user [arg3] from [arg4] at IP address [arg5].Informational
FQXSPSE4039ITemporary user account [arg1] is created by inband tool.Informational
FQXSPSE4040ITemporary user account [arg1] expires.Informational
FQXSPSE4042IThe third-party password function [arg1] by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPSE4043IRetrieving the third-party password [arg1] by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPSE4044IUser [arg1] third-party hashed password has been [arg2] by user [arg3] from [arg4] at IP address [arg5].Informational
FQXSPSE4045IThe Salt of user [arg1] third-party password has been [arg2] by user [arg3] from [arg4] at IP address [arg5].Informational
FQXSPSE4046IThe third-party password of the user [arg1] has been retrieved by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPSE4047IRole [arg1] is [arg2] and assigned with custom privileges [arg3] by user [arg4] from [arg5] at IP address [arg6].Informational
FQXSPSE4048IRole [arg1] is removed by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPSE4049IRole [arg1] is assigned to user [arg2] by user [arg3] from [arg4] at IP address [arg5].Informational
FQXSPSE4050I[arg1] sent IPMI command from [arg2], raw data: [arg3][arg4][arg5].Informational
FQXSPSE4051IManagement Controller [arg1] joined the neighbor group [arg2] by user [arg3] from [arg4] at IP address [arg5].Informational
FQXSPSE4052IThe password of neighbor group [arg1] is modified by [arg2] [arg3] from [arg4] at IP address [arg5].Informational
FQXSPSE4053IManagement Controller [arg1] left the neighbor group [arg2] by user [arg3] from [arg4] at IP address [arg5].Informational
FQXSPSE4054IIPMI SEL wrapping mode is [arg1] by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPSE4055ISED encryption is enabled by user [arg1] from [arg2] at IP address [arg3].Informational
FQXSPSE4056ISED AK is [arg1] by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPSE4057IUser [arg1] created by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPSE4058IUser [arg1] removed by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPSE4059IUser [arg1] password modified by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPSE4060IUser [arg1] role set to [arg2] by user [arg3] from [arg4] at IP address [arg5].Informational
FQXSPSE4061IUser [arg1] custom privileges set: [arg2] by user [arg3] from [arg4] at IP address [arg5].Informational
FQXSPSE4062IThe system guard snapshot is captured by user [arg1] from [arg2] at IP address [arg3].Informational
FQXSPSE4063IThe system guard configuration is updated: status=[arg1], hardware inventory=[arg2] and action=[arg3] by user [arg4] from [arg5] at IP address [arg6].Informational
FQXSPSE4064ISNMPv3 engine ID is changed from [arg1] to [arg2] by user [arg3] from [arg4] at IP address [arg5].Informational
FQXSPSE4065ISFTP [arg1] by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPSE4066ISecurity mode is modified from [arg1] to [arg2] by user [arg3] from [arg4] at IP address [arg5].Informational
FQXSPSE4067IUser [arg1] accessible interfaces is set to [arg2] by user [arg3] from [arg4] at IP address [arg5].Informational
FQXSPSE4068ISecurity: Userid: [arg1] using [arg2] had [arg3] login failures from Redfish client at IP address [arg4].Informational
FQXSPSE4069ILDAP set by user [arg1]: RootDN=[arg2], UIDSearchAttribute=[arg3], BindingMethod=[arg4], TargetName=[arg5], GroupFilter=[arg6], GroupAttribute=[arg7], LoginAttribute=[arg8] from [arg9] at IP address [arg10].Informational
FQXSPSE4074ISecurity mode downgrades because the XCC3 Premier Upgrade key is expired or deleted.Informational
FQXSPSE4079IThe Operator role is [arg1] to contain Remote Console Access permission by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPSE4080IThe user [arg1] attempts to clear CMOS from [arg2] at IP address [arg3].Informational
FQXSPSE4081IBMC returns the valid local cached key to UEFI for SED drives.Informational
FQXSPSE4082IRemote key management server is inaccessible.Informational
FQXSPSE4083IThe local cached key has expired and destroyed it.Informational
FQXSPSE4084IPeriodic connection to remote key management server succeeded.Informational
FQXSPSE4085IPeriodic connection to remote key management server failed.Informational
FQXSPSE4091ISNMPv2 [arg1] set by user [arg2]: Name=[arg3], AccessType=[arg4], Address=[arg5].Informational
FQXSPSE4092ISNMPv1 Community-1 set by user [arg1]: Name=[arg2], AccessType=trap from [arg3] at IP address [arg4].Informational
FQXSPSE4093ISNMPv1 Community-1 set by user [arg1]: address=[arg2] from [arg3] at IP address [arg4].Informational
FQXSPSE4094ISNMPv2 Community-1 set by user [arg1]: Name=[arg2], AccessType=trap from [arg3] at IP address [arg4].Informational
FQXSPSE4095ISNMPv2 Community-1 set by user [arg1]: address=[arg2] from [arg3] at IP address [arg4].Informational
FQXSPSE4096IUser [arg1] for SNMPv3 trap set: AuthenticationProtocol=[arg2], PrivacyProtocol=[arg3], HostforTraps=[arg4] by user [arg5] from [arg6] at IP address [arg7].Informational
FQXSPSE4097IUser [arg1] for SNMPv3 trap is deleted by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPSE4098ISecurity: Userid: [arg1] failed to login from [arg2] at IP address [arg3].Informational
FQXSPSE4099IUser [arg1] was created from [arg2].Informational
FQXSPSE4100IUser [arg1] was removed from [arg2].Informational
FQXSPSE4101IUser [arg1] password was modified from [arg2].Informational
FQXSPSE4102IUser [arg1] role was set to [arg2] from [arg3].Informational
FQXSPSE4103IThe extended audit log setting is [arg1] by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPSE4104ISSDP is [arg1] by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPSE4129ISecurity: Userid: [arg1] failed to login from SNMP client at IP address [arg2].Informational
FQXSPSS4000IManagement Controller Test Alert Generated by [arg1] from [arg2] at IP address [arg3].Informational
FQXSPSS4001IServer General Settings set by user [arg1]: Name=[arg2], Contact=[arg3], Location=[arg4], Room=[arg5], RackID=[arg6], Rack U-position=[arg7], Address=[arg8] from [arg9] at IP address [arg10].Informational
FQXSPSS4002ILicense key for [arg1] added by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPSS4003ILicense key for [arg1] removed by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPSS4004ITest Call Home Generated by user [arg1] from [arg2] at IP address [arg3].Informational
FQXSPSS4006ICall Home to [arg1] failed to complete: [arg2].Informational
FQXSPSS4007IThe BMC functionality tier is changed from [arg1] to [arg2].Informational
FQXSPSS4008IThe UEFI setting has been changed by user [arg1] from address [arg2]. A total of [arg3] items were changed in the request.Informational
FQXSPSS4009ISystem enters LXPM maintenance mode.Informational
FQXSPSS4010ITest Audit Log generated by user [arg1] from [arg2] at IP address [arg3].Informational
FQXSPSS4011IFan speed boost setting is changed from [arg1] to [arg2].Informational
FQXSPSS4012IThe [arg1] setting has been changed to [arg2] by user [arg3] from [arg4] at IP address [arg5].Informational
FQXSPTR4001IDate and Time set by user [arg1]: Date=[arg2], Time-[arg3], DST Auto-adjust=[arg4], Timezone=[arg5] from [arg6] at IP address [arg7].Informational
FQXSPTR4002ISynchronize time setting by user [arg1]: Mode=Sync with NTP Server, NTPServerHost1=[arg2],NTPServerHost2=[arg3],NTPServerHost3=[arg4],NTPServerHost4=[arg5],NTPUpdateFrequency=[arg6] from [arg7] at IP address [arg8].Informational
FQXSPTR4003ISynchronize time setting by user [arg1]: Mode=Sync with server clock from [arg2] at IP address [arg3].Informational
FQXSPUN0017IThe cooling liquid has stopped leaking and transitioned to normal state with sensor [DripName].Informational
FQXSPUN0026ILow Security Jumper is enabled.Informational
FQXSPUN0048IThe RAID controller in PCI slot [PCILocation] in optimal status.Informational
FQXSPUN0057IThe RAID controller in PCI slot [PCILocation] does not have a battery.Informational
FQXSPUN0061ISystem Maintenance Mode has asserted.Informational
FQXSPUN0062ISMI Timeout has asserted.Informational
FQXSPUN0063IPSU heavy load has asserted.Informational
FQXSPUN2012IBMC firmware corrupted has deasserted.Informational
FQXSPUN2026ILow Security Jumper is disabled.Informational
FQXSPUN2049IThe RAID controller in PCI slot [PCILocation] is no longer in warning status.Informational
FQXSPUN2050IThe RAID controller in PCI slot [PCILocation] is no longer in critical status.Informational
FQXSPUN2057IThe RAID controller in PCI slot [PCILocation] has a battery now.Informational
FQXSPUN2058IThe remaining life for all SSDs is above threshold [ThresholdValue].Informational
FQXSPUN2061ISystem Maintenance Mode has deasserted.Informational
FQXSPUN2062ISMI Timeout has deasserted.Informational
FQXSPUN2063IPSU heavy load has deasserted.Informational
FQXSPUN2065IUEFI firmware is automatically recovered from authentication failure.Informational
FQXSPUN2067IUEFI firmware is manually recovered from authentication failure.Informational
FQXSPUN2068I[DriveName] Mismatch has transitioned to a less severe state from critical.Informational
FQXSPUP0002IA firmware or software change occurred on system [ComputerSystemName].Informational
FQXSPUP4006IAuto promote primary XCC to backup is [arg1] by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPUP4007IViolation access to XCC SPI flash is detected and isolated.Informational
FQXSPUP4008IViolation access to UEFI SPI flash is detected and isolated.Informational
FQXSPUP4010IUpdate [arg1] of [arg2] from [arg3] succeeded for user [arg4].Informational
FQXSPUP4011IUpdate [arg1] of [arg2] from [arg3] failed for user [arg4].Informational
FQXSPUP4012IFirmware update task [arg1] was interrupted by BMC reboot.Informational
FQXSPWD0000IWatchdog Timer expired for [WatchdogName].Informational
FQXSPWD0001IReboot of system [ComputerSystemName] initiated by watchdog [WatchdogName].Informational
FQXSPWD0002IPowering off system [ComputerSystemName] initiated by watchdog [WatchdogName].Informational
FQXSPWD0003IPower cycle of system [ComputerSystemName] initiated by watchdog [WatchdogName].Informational
FQXSPWD0004IWatchdog Timer interrupt occurred for [WatchdogName].Informational
FQXSPCA0000JFan [NumericSensorName] going low (lower non-critical) has asserted.Warning
FQXSPCA0007JAmbient temperature going high (upper non-critical) has asserted.Warning
FQXSPCA0046JDIMM [DIMMId] temperature going high (upper non-critical) has asserted.Warning
FQXSPCA0049JPump tach [pumpFanIndex] going high (upper non-critical) has asserted.Warning
FQXSPCP0001GDevice [DeviceName] mismatches with the system.Warning
FQXSPEA0003JLink down is detected on port [PCIPortNumber] of the PCIe device [PCIDeviceName].Warning
FQXSPEM4043IA [arg1] failure has been detected and need [arg2] to recover.Warning
FQXSPIO0014JBus [BusName] is operating in a degraded state.Warning
FQXSPIO0035G[DeviceName] is installed in wrong location.Warning
FQXSPIO2000JThe connector [PhysicalConnectorName] has been disconnected.Warning
FQXSPMA0010JDIMM [DIMMId] on system [MemoryName] is throttled.Warning
FQXSPMA0039GDIMM [DIMMID] is disabled.Warning
FQXSPNM4010IDHCP[[arg1]] failure, no IP address assigned.Warning
FQXSPPP4009IThe measured power value exceeded the power cap value.Warning
FQXSPPU0002GProcessor [ProcessorId] is operating in a Degraded State.Warning
FQXSPPU0010GProcessor [ProcessorId] is operating in a Degraded State due to [ElementSource].Warning
FQXSPPU0015GCPU feature mismatch is detected.Warning
FQXSPPW0003GFailure predicted on power supply [PowerSupplyId].Warning
FQXSPPW0006IPower supply [PowerSupplyId] has lost input.Warning
FQXSPPW0007IPower supply [PowerSupplyId] in the enclosure/chassis (MTM-S/N: [MachineSerialNumber]) has lost input.Warning
FQXSPPW0031JCMOS battery voltage going low (lower non-critical) has asserted.Warning
FQXSPPW0057JPSU [SensorName] prediction fault failure has transitioned from normal to non-critical state.Warning
FQXSPPW0101JRedundancy Degraded for Power Resource has asserted.Warning
FQXSPPW0104JNon-redundant:Sufficient Resources from Redundancy Degraded or Fully Redundant for Power Resource has asserted.Warning
FQXSPSD0002GFailure Predicted on [DriveName].Warning
FQXSPSD0003GFailure Predicted on drive [DriveLocation] in the enclosure/chassis (MTM-S/N: [MachineSerialNumber]).Warning
FQXSPSE0000FThe Chassis [ComputerSystemName] was opened.Warning
FQXSPSE0010JSystem Guard detected inventory mismatch with trusted snapshot.Warning
FQXSPSE4006IXCC detected an invalid SSL certificate in the Management Controller [arg1].Warning
FQXSPSS0012G[System] cannot detect [DeviceName].Warning
FQXSPUN0009GBMC firmware corruption is detected.Warning
FQXSPUN0049JThe RAID controller in PCIe slot [PCILocation] is in warning status. At least one physical drive is in unconfigured bad state.Warning
FQXSPUN0051JThe RAID controller in PCIe slot [PCILocation] has asserted a warning. Foreign configuration is detected.Warning
FQXSPUN0058JThe remaining life of [DriveName] is lower than the warning threshold ([ThresholdValue]).Warning
FQXSPUN0059JRoT attestation has detected a failure.Warning
FQXSPUN0060GRoT mismatch has asserted.Warning
FQXSPUN0065JUEFI firmware authentication failure is detected.Warning
FQXSPUP0007LBMC primary firmware is corrupted, auto fail over to backup.Warning
FQXSPBR4003IOS Watchdog Timer expired for [arg1].Error
FQXSPBR4007IManagement Controller [arg1]: Configuration restoration from a file by user [arg2] failed to complete from [arg3] at IP address [arg4].Error
FQXSPBR4008IManagement Controller [arg1]: Configuration restoration from a file by user [arg2] failed to start from [arg3] at IP address [arg4].Error
FQXSPCA0002MFan [NumericSensorName] going low (lower critical) has asserted.Error
FQXSPCA0009MAmbient temperature going high (upper critical) has asserted.Error
FQXSPCA0011NAmbient temperature going high (upper non-recoverable) has asserted.Error
FQXSPCA0016MFan Mismatch has transitioned to critical from a less severe state.Error
FQXSPCA0017MPCIe [SensorName] overtemperature has transitioned to critical from a less severe state.Error
FQXSPCA0019NPCIe [SensorName] overtemperature has transitioned to non-recoverable from a less severe state.Error
FQXSPCA0040NLiquid is leaking from open loop [CoolingSensorName].Error
FQXSPCA0041NLiquid is leaking from closed loop [CoolingSensorName].Error
FQXSPCA0042MLiquid leak detector for [DeviceType] is faulty.Error
FQXSPCA0047MDIMM [DIMMId] temperature going high (upper critical) has asserted.Error
FQXSPCA0048MDIMM [DIMMId] temperature going high (upper non-recoverable) has asserted.Error
FQXSPCA0050MPump tach [pumpFanIndex] going high (upper critical) has asserted.Error
FQXSPCA0051NPump tach [pumpFanIndex] going high (upper non-recoverable) has asserted.Error
FQXSPCA0052MPump tach [pumpFanIndex] going low (lower critical) has asserted.Error
FQXSPFW0001NFirmware BIOS (ROM) corruption was detected on system [ComputerSystemName] during POST.Error
FQXSPIO0004LA bus timeout has occurred on bus [BusName].Error
FQXSPIO0006NA software NMI has occurred on system [ComputerSystemName].Error
FQXSPIO0011NAn Uncorrectable Error has occurred on PCIs.Error
FQXSPIO0013NA Fatal Bus Error has occurred on bus [BusName].Error
FQXSPIO0024M[BackplaneName] has invalid cabling configuration.Error
FQXSPMA0012MAn Over-Temperature Condition has been detected on the DIMM [DIMMId] on system [MemoryName].Error
FQXSPMA0130NMemory PMIC [MemoryPMICGroup] has transitioned to non-recoverable.Error
FQXSPOS4002IWatchdog [arg1] Failed to Capture Screen.Error
FQXSPOS4003IPlatform Watchdog Timer expired for [arg1].Error
FQXSPOS4010IOS Crash Video Capture Failed.Error
FQXSPPU0001NAn Over-Temperature Condition has been detected on Processor [ProcessorId].Error
FQXSPPU0007NCPU voltage mismatch detected on [ProcessorName].Error
FQXSPPU0009NProcessor [ProcessorId] has a Configuration Mismatch.Error
FQXSPPU0016NAn Uncorrectable Error has occurred on CPUs.Error
FQXSPPU0017NA hard fault has occurred on processor [ProcessorId].Error
FQXSPPW0002LPower supply [PowerSupplyId] has Failed.Error
FQXSPPW0003LPower supply [PowerSupplyId] in the enclosure/chassis (MTM-S/N: [MachineSerialNumber]) has failed.Error
FQXSPPW0007LPower supply [PowerSupplyId] has a Configuration Mismatch.Error
FQXSPPW0061MPSU [SensorName] failure has transitioned to critical from a less severe state.Error
FQXSPPW0062MPSU mismatch has transitioned to critical from a less severe state.Error
FQXSPPW0110MNon-redundant:Insufficient Resources for Power Resource has asserted.Error
FQXSPPW0123MPSU [SensorName] input failure has transitioned to critical from a less severe state.Error
FQXSPPW0129NCPU [ProcessorId] [VRName] has transitioned to non-recoverable.Error
FQXSPPW0131NPeripheral device [DeviceName] powergood has transitioned to non-recoverable.Error
FQXSPPW0132NFan [FanGroup] powergood has transitioned to non-recoverable.Error
FQXSPPW0133NMB AUX powergood has transitioned to non-recoverable.Error
FQXSPPW0134MCMOS battery voltage going low (lower critical) has asserted.Error
FQXSPPW0135JInvalid redundancy config, current PSU config doesn't support Non-redundant mode.Error
FQXSPSD0001LThe [DriveName] has a fault.Error
FQXSPSD0002LDrive [DriveLocation] in the enclosure/chassis (MTM-S/N: [MachineSerialNumber]) has a fault.Error
FQXSPSE4000ICertificate Authority [arg1] has detected a Certificate Error.Error
FQXSPUN0050MThe RAID controller in PCIe slot [PCILocation] is in critical state. Volume [VolumeID] is offline.Error
FQXSPUN0053MThe RAID controller in PCIe slot [PCILocation] is in critical status. At least one physical drive is failed.Error
FQXSPUN0054MThe RAID controller in PCIe slot [PCILocation] is in critical status. Volume [VolumeID] is degraded.Error
FQXSPUN0055MThe RAID controller in PCIe slot [PCILocation] is in critical state. Battery is in non-optimal state.Error
FQXSPUN0067MFailed to automatically recover UEFI firmware from authentication failure.Error
FQXSPUN0068M[DriveName] Mismatch has transitioned to critical from a less severe state.Error
FQXSPUN0069MThe remaining life of [DriveName] is lower than the critical threshold ([ThresholdValue]).Error
FQXSPUP4003I[arg1] firmware mismatches with system firmware. Please attempt to flash the [arg2] firmware.Error
FQXSPUP4009IPlease ensure that the system is flashed with the correct [arg1] firmware. The Management Controller is unable to match the firmware to the server.Error