Skip to main content

Test results for the DSA Broadcom network test

The following messages can result when you run the DSA Broadcom network test.

  • 405-000-000 : BRCM:TestControlRegisters Test Passed

    The test passed.
    Recoverable
    No
    Severity
    Event
    Serviceable
    No
    Automatically notify support
    No
    Related links

  • 405-001-000 : BRCM:TestMIIRegisters Test Passed

    The test passed.
    Recoverable
    No
    Severity
    Event
    Serviceable
    No
    Automatically notify support
    No
    Related links

  • 405-002-000 : BRCM:TestEEPROM Test Passed

    The test passed.
    Recoverable
    No
    Severity
    Event
    Serviceable
    No
    Automatically notify support
    No
    Related links

  • 405-003-000 : BRCM:TestInternalMemory Test Passed

    The test passed.
    Recoverable
    No
    Severity
    Event
    Serviceable
    No
    Automatically notify support
    No
    Related links

  • 405-004-000 : BRCM:TestInterrupt Test Passed

    The test passed.
    Recoverable
    No
    Severity
    Event
    Serviceable
    No
    Automatically notify support
    No
    Related links

  • 405-005-000 : BRCM:TestLoopbackMAC Test Passed

    The test passed.
    Recoverable
    No
    Severity
    Event
    Serviceable
    No
    Automatically notify support
    No
    Related links

  • 405-006-000 : BRCM:TestLoopbackPhysical Test Passed

    The test passed.
    Recoverable
    No
    Severity
    Event
    Serviceable
    No
    Automatically notify support
    No
    Related links

  • 405-007-000 : BRCM:TestLEDs Test Passed

    The test passed.
    Recoverable
    No
    Severity
    Event
    Serviceable
    No
    Automatically notify support
    No
    Related links

  • 405-800-000 : BRCM:TestControlRegisters Test Aborted

    The control registers test was canceled.
    Recoverable
    No
    Severity
    Warning
    Serviceable
    No
    Automatically notify support
    No
    Related links

  • 405-801-000 : BRCM:TestMIIRegisters Test Aborted

    The MII register test was canceled.
    Recoverable
    No
    Severity
    Warning
    Serviceable
    No
    Automatically notify support
    No
    Related links

  • 405-802-000 : BRCM:TestEEPROM Test Aborted

    The EEPROM test was canceled.
    Recoverable
    No
    Severity
    Warning
    Serviceable
    No
    Automatically notify support
    No
    Related links

  • 405-803-000 : BRCM:TestInternalMemory Test Aborted

    The internal memory test was canceled.
    Recoverable
    No
    Severity
    Warning
    Serviceable
    No
    Automatically notify support
    No
    Related links

  • 405-804-000 : BRCM:TestInterrupt Test Aborted

    The interrupt test was canceled.
    Recoverable
    No
    Severity
    Warning
    Serviceable
    No
    Automatically notify support
    No
    Related links

  • 405-805-000 : BRCM:TestLoopbackMAC Test Aborted

    Loopback testing at the MAC layer was canceled.
    Recoverable
    No
    Severity
    Warning
    Serviceable
    No
    Automatically notify support
    No
    Related links

  • 405-806-000 : BRCM:TestLoopbackPhysical Test Aborted

    Loopback testing at the physical layer was canceled.
    Recoverable
    No
    Severity
    Warning
    Serviceable
    No
    Automatically notify support
    No
    Related links

  • 405-807-000 : BRCM:TestLEDs Test Aborted

    Verification of status LEDs was canceled.
    Recoverable
    No
    Severity
    Warning
    Serviceable
    No
    Automatically notify support
    No
    Related links

  • 405-900-000 : BRCM:TestControlRegisters Test Failed

    A failure was detected while testing internal MAC registers
    Recoverable
    No
    Severity
    Error
    Serviceable
    Yes
    Automatically notify support
    No
    User Response
    Complete the following steps:
    1. Check component firmware level and upgrade if necessary. The installed firmware level can be found in the DSA Diagnostic Event Log within the Firmware/VPD section for this component.
    2. Rerun the test.
    3. If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service Guide" for the next corrective action.
    Related links

  • 405-901-000 : BRCM:TestMIIRegisters Test Failed

    A failure was detected while testing internal PHY registers.
    Recoverable
    No
    Severity
    Error
    Serviceable
    Yes
    Automatically notify support
    No
    User Response
    Complete the following steps:
    1. Check component firmware level and upgrade if necessary. The installed firmware level can be found in the DSA Diagnostic Event Log within the Firmware/VPD section for this component.
    2. Rerun the test.
    3. If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service Guide" for the next corrective action.
    Related links

  • 405-902-000 : BRCM:TestEEPROM Test Failed

    A failure was detected while testing non-volatile RAM.
    Recoverable
    No
    Severity
    Error
    Serviceable
    Yes
    Automatically notify support
    No
    User Response
    Complete the following steps:
    1. Check component firmware level and upgrade if necessary. The installed firmware level can be found in the DSA Diagnostic Event Log within the Firmware/VPD section for this component.
    2. Rerun the test.
    3. If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service Guide" for the next corrective action.
    Related links

  • 405-903-000 : BRCM:TestInternalMemory Test Failed

    A failure was detected while testing internal memory.
    Recoverable
    No
    Severity
    Error
    Serviceable
    Yes
    Automatically notify support
    No
    User Response
    Complete the following steps:
    1. Check component firmware level and upgrade if necessary. The installed firmware level can be found in the DSA Diagnostic Event Log within the Firmware/VPD section for this component.
    2. Rerun the test.
    3. If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service Guide" for the next corrective action.
    Related links

  • 405-904-000 : BRCM:TestInterrupt Test Failed

    A failure was detected while testing interrupts.
    Recoverable
    No
    Severity
    Error
    Serviceable
    Yes
    Automatically notify support
    No
    User Response
    Complete the following steps:
    1. Check component firmware level and upgrade if necessary. The installed firmware level can be found in the DSA Diagnostic Event Log within the Firmware/VPD section for this component.
    2. Rerun the test.
    3. If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service Guide" for the next corrective action.
    Related links

  • 405-905-000 : BRCM:TestLoopbackMAC Test Failed

    BRCM:TestLoopbackMAC Test Failed.
    Recoverable
    No
    Severity
    Error
    Serviceable
    Yes
    Automatically notify support
    No
    User Response
    Complete the following steps:
    1. Check component firmware level and upgrade if necessary. The installed firmware level can be found in the DSA Diagnostic Event Log within the Firmware/VPD section for this component.
    2. Rerun the test.
    3. If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service Guide" for the next corrective action.
    Related links

  • 405-906-000 : BRCM:TestLoopbackPhysical Test Failed

    A failure was detected during the loopback test at the physical layer.
    Recoverable
    No
    Severity
    Error
    Serviceable
    Yes
    Automatically notify support
    No
    User Response
    Complete the following steps:
    1. Check component firmware level and upgrade if necessary. The installed firmware level can be found in the DSA Diagnostic Event Log within the Firmware/VPD section for this component.
    2. Rerun the test.
    3. If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service Guide" for the next corrective action.
    Related links

  • 405-907-000 : BRCM:TestLEDs Test Failed

    A failure was detected while verifying operation of the status LEDs.
    Recoverable
    No
    Severity
    Error
    Serviceable
    Yes
    Automatically notify support
    No
    User Response
    Complete the following steps:
    1. Check component firmware level and upgrade if necessary. The installed firmware level can be found in the DSA Diagnostic Event Log within the Firmware/VPD section for this component.
    2. Rerun the test.
    3. If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service Guide" for the next corrective action.
    Related links