TMM error messages
Use this information to resolve any issues that were found.
Diagnostic Code:
04010401
04010402
04010403
04010404
04010405
Full Sensor Name (Sensor Name In SDR):
Fan%_Speed (% = Fan number)
Sensor Type:
Fan
Event Severity:
Critical
Description:
Lower Non-Recoverable - Going Low - Asserted
Message:
Fan% speed is too low.
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Check Fan status. if Fan is broken, please replace the new Fan.
3. Contact your Lenovo service representative for support
Diagnostic Code:
02010410
Full Sensor Name (Sensor Name In SDR):
SYS_12V
Sensor Type:
Voltage
Event Severity:
Critical
Description:
Lower Non-Recoverable - Going Low - Asserted
Message:
12V voltage is too low
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
02010210
Full Sensor Name (Sensor Name In SDR):
SYS_12V
Sensor Type:
Voltage
Event Severity:
Critical
Description:
Lower Critical - Going Low - Asserted
Message:
12 voltage is too low
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
02010010
Full Sensor Name (Sensor Name In SDR):
SYS_12V
Sensor Type:
Voltage
Event Severity:
Warning
Description:
Lower Non-Critical - Going Low - Asserted
Message:
12V voltage is too low
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
02010B10
Full Sensor Name (Sensor Name In SDR):
SYS_12V
Sensor Type:
Voltage
Event Severity:
Critical
Description:
Upper Non-Recoverable - Going High - Asserted
Message:
12V voltage is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
02010910
Full Sensor Name (Sensor Name In SDR):
SYS_12V
Sensor Type:
Voltage
Event Severity:
Critical
Description:
Upper Critical - Going High - Asserted
Message:
12V voltage is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
02010710
Full Sensor Name (Sensor Name In SDR):
SYS_12V
Sensor Type:
Voltage
Event Severity:
Warning
Description:
Upper Non-Critical - Going High - Asserted
Message:
12V voltage is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
02010411
Full Sensor Name (Sensor Name In SDR):
SYS_5V
Sensor Type:
Voltage
Event Severity:
Critical
Description:
Lower Non-Recoverable - Going Low - Asserted
Message:
5V voltage is too low
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
02010211
Full Sensor Name (Sensor Name In SDR):
SYS_5V
Sensor Type:
Voltage
Event Severity:
Critical
Description:
Lower Critical - Going Low - Asserted
Message:
5V voltage is too low
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
02010011
Full Sensor Name (Sensor Name In SDR):
SYS_5V
Sensor Type:
Voltage
Event Severity:
Warning
Description:
Lower Non-Critical - Going Low - Asserted
Message:
5V voltage is too low
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
02010B11
Full Sensor Name (Sensor Name In SDR):
SYS_5V
Sensor Type:
Voltage
Event Severity:
Critical
Description:
Upper Non-Recoverable - Going High - Asserted
Message:
5V voltage is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
02010911
Full Sensor Name (Sensor Name In SDR):
SYS_5V
Sensor Type:
Voltage
Event Severity:
Critical
Description:
Upper Critical - Going High - Asserted
Message:
5V voltage is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
02010711
Full Sensor Name (Sensor Name In SDR):
SYS_5V
Sensor Type:
Voltage
Event Severity:
Warning
Description:
Upper Non-Critical - Going High - Asserted
Message:
5V voltage is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
02010412
Full Sensor Name (Sensor Name In SDR):
SYS_3.3.V
Sensor Type:
Voltage
Event Severity:
Critical
Description:
Lower Non-Recoverable - Going Low - Asserted
Message:
3.3V voltage is too low
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
02010212
Full Sensor Name (Sensor Name In SDR):
SYS_3.3.V
Sensor Type:
Voltage
Event Severity:
Critical
Description:
Lower Critical - Going Low - Asserted
Message:
3.3V voltage is too low
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
02010012
Full Sensor Name (Sensor Name In SDR):
SYS_3.3.V
Sensor Type:
Voltage
Event Severity:
Warning
Description:
Lower Non-Critical - Going Low - Asserted
Message:
3.3V voltage is too low
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
02010B12
Full Sensor Name (Sensor Name In SDR):
SYS_3.3.V
Sensor Type:
Voltage
Event Severity:
Critical
Description:
Upper Non-Recoverable - Going High - Asserted
Message:
3.3V voltage is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
02010912
Full Sensor Name (Sensor Name In SDR):
SYS_3.3.V
Sensor Type:
Voltage
Event Severity:
Critical
Description:
Upper Critical - Going High - Asserted
Message:
3.3V voltage is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
02010712
Full Sensor Name (Sensor Name In SDR):
SYS_3.3.V
Sensor Type:
Voltage
Event Severity:
Warning
Description:
Upper Non-Critical - Going High - Asserted
Message:
3.3V voltage is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
02010413
02010414
Full Sensor Name (Sensor Name In SDR):
CPU%_VCORE (% = CPU number)
Sensor Type:
Voltage
Event Severity:
Critical
Description:
Lower Non-Recoverable - Going Low - Asserted
Message:
CPU% VCORE voltage is too low
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
02010213
02010214
Full Sensor Name (Sensor Name In SDR):
CPU%_VCORE (% = CPU number)
Sensor Type:
Voltage
Event Severity:
Critical
Description:
Lower Critical - Going Low - Asserted
Message:
CPU% VCORE voltage is too low
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
02010013
02010014
Full Sensor Name (Sensor Name In SDR):
CPU%_VCORE (% = CPU number)
Sensor Type:
Voltage
Event Severity:
Warning
Description:
Lower Non-Critical - Going Low - Asserted
Message:
CPU% VCORE voltage is too low
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
02010B13
02010B14
Full Sensor Name (Sensor Name In SDR):
CPU%_VCORE (% = CPU number)
Sensor Type:
Voltage
Event Severity:
Critical
Description:
Upper Non-Recoverable - Going High - Asserted
Message:
CPU% VCORE voltage is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
02010913
02010914
Full Sensor Name (Sensor Name In SDR):
CPU%_VCORE (% = CPU number)
Sensor Type:
Voltage
Event Severity:
Critical
Description:
Upper Critical - Going High - Asserted
Message:
CPU% VCORE voltage is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
02010713
02010714
Full Sensor Name (Sensor Name In SDR):
CPU%_VCORE (% = CPU number)
Sensor Type:
Voltage
Event Severity:
Warning
Description:
Upper Non-Critical - Going High - Asserted
Message:
CPU% VCORE voltage is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
01010B20
Full Sensor Name (Sensor Name In SDR):
Inlet_Temp
Sensor Type:
Temperature
Event Severity:
Critical
Description:
Upper Non-Recoverable - Going High - Asserted
Message:
Inlet temperature is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Check Fan status. if Fan is broken, please replace the new Fan.
3. Contact your Lenovo service representative for support
Diagnostic Code:
01010920
Full Sensor Name (Sensor Name In SDR):
Inlet_Temp
Sensor Type:
Temperature
Event Severity:
Critical
Description:
Upper Critical - Going High - Asserted
Message:
Inlet temperature is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Check Fan status. if Fan is broken, please replace the new Fan.
3. Contact your Lenovo service representative for support
Diagnostic Code:
01010720
Full Sensor Name (Sensor Name In SDR):
Inlet_Temp
Sensor Type:
Temperature
Event Severity:
Warning
Description:
Upper Non-Critical - Going High - Asserted
Message:
Inlet temperature is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Check Fan status. if Fan is broken, please replace the new Fan.
3. Contact your Lenovo service representative for support
Diagnostic Code:
01010B21
Full Sensor Name (Sensor Name In SDR):
Outlet_Temp
Sensor Type:
Temperature
Event Severity:
Critical
Description:
Upper Non-Recoverable - Going High - Asserted
Message:
Outlet temperature is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Check Fan status. if Fan is broken, please replace the new Fan.
3. Contact your Lenovo service representative for support
Diagnostic Code:
01010921
Full Sensor Name (Sensor Name In SDR):
Outlet_Temp
Sensor Type:
Temperature
Event Severity:
Critical
Description:
Upper Critical - Going High - Asserted
Message:
Outlet temperature is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Check Fan status. if Fan is broken, please replace the new Fan.
3. Contact your Lenovo service representative for support
Diagnostic Code:
01010721
Full Sensor Name (Sensor Name In SDR):
Outlet_Temp
Sensor Type:
Temperature
Event Severity:
Warning
Description:
Upper Non-Critical - Going High - Asserted
Message:
Outlet temperature is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Check Fan status. if Fan is broken, please replace the new Fan.
3. Contact your Lenovo service representative for support
Diagnostic Code:
01010722
01010723
Full Sensor Name (Sensor Name In SDR):
CPU0%_Temp
Sensor Type:
Temperature
Event Severity:
Warning
Description:
Upper Non-Critical - Going High - Asserted
Message:
CPU% temperature is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Check Fan status. if Fan is broken, please replace the new Fan.
3. Contact your Lenovo service representative for support
Diagnostic Code:
01010B26
01010B27
Full Sensor Name (Sensor Name In SDR):
CPU%_VR_Temp (% = CPU Number)
Sensor Type:
Temperature
Event Severity:
Critical
Description:
Upper Non-Recoverable - Going High - Asserted
Message:
CPU% VR temperature is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Check Fan status. if Fan is broken, please replace the new Fan.
3. Contact your Lenovo service representative for support
Diagnostic Code:
01010926
01010927
Full Sensor Name (Sensor Name In SDR):
CPU%_VR_Temp (% = CPU Number)
Sensor Type:
Temperature
Event Severity:
Critical
Description:
Upper Critical - Going High - Asserted
Message:
CPU% VR temperature is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Check Fan status. if Fan is broken, please replace the new Fan.
3. Contact your Lenovo service representative for support
Diagnostic Code:
01010726
01010727
Full Sensor Name (Sensor Name In SDR):
CPU%_VR_Temp (% = CPU Number)
Sensor Type:
Temperature
Event Severity:
Warning
Description:
Upper Non-Critical - Going High - Asserted
Message:
CPU% VR temperature is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Check Fan status. if Fan is broken, please replace the new Fan.
3. Contact your Lenovo service representative for support
Diagnostic Code:
01010B28
Full Sensor Name (Sensor Name In SDR):
Node_PBP_Temp
Sensor Type:
Temperature
Event Severity:
Critical
Description:
Upper Non-Recoverable - Going High - Asserted
Message:
Power IC is over temperature
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Check Fan status. if Fan is broken, please replace the new Fan.
3. Contact your Lenovo service representative for support
Diagnostic Code:
01010928
Full Sensor Name (Sensor Name In SDR):
Node_PBP_Temp
Sensor Type:
Temperature
Event Severity:
Critical
Description:
Upper Critical - Going High - Asserted
Message:
Power IC is over temperature
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Check Fan status. if Fan is broken, please replace the new Fan.
3. Contact your Lenovo service representative for support
Diagnostic Code:
01010728
Full Sensor Name (Sensor Name In SDR):
Node_PBP_Temp
Sensor Type:
Temperature
Event Severity:
Warning
Description:
Upper Non-Critical - Going High - Asserted
Message:
Power IC is over temperature
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Check Fan status. if Fan is broken, please replace the new Fan.
3. Contact your Lenovo service representative for support
Diagnostic Code:
01010B29
Full Sensor Name (Sensor Name In SDR):
PCH_Temp
Sensor Type:
Temperature
Event Severity:
Critical
Description:
Upper Non-Recoverable - Going High - Asserted
Message:
PCH temperature is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Check Fan status. if Fan is broken, please replace the new Fan.
3. Contact your Lenovo service representative for support
Diagnostic Code:
01010929
Full Sensor Name (Sensor Name In SDR):
PCH_Temp
Sensor Type:
Temperature
Event Severity:
Critical
Description:
Upper Critical - Going High - Asserted
Message:
PCH temperature is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Check Fan status. if Fan is broken, please replace the new Fan.
3. Contact your Lenovo service representative for support
Diagnostic Code:
01010729
Full Sensor Name (Sensor Name In SDR):
PCH_Temp
Sensor Type:
Temperature
Event Severity:
Warning
Description:
Upper Non-Critical - Going High - Asserted
Message:
PCH temperature is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Check Fan status. if Fan is broken, please replace the new Fan.
3. Contact your Lenovo service representative for support
Diagnostic Code:
01010B2A
01010B2B
Full Sensor Name (Sensor Name In SDR):
DIMMG%_Temp (% = Group number)
Sensor Type:
Temperature
Event Severity:
Critical
Description:
Upper Non-Recoverable - Going High - Asserted
Message:
DIMM Group% temperature is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Check Fan status. if Fan is broken, please replace the new Fan.
3. Contact your Lenovo service representative for support
Diagnostic Code:
0101092A
0101092B
Full Sensor Name (Sensor Name In SDR):
DIMMG%_Temp (% = Group number)
Sensor Type:
Temperature
Event Severity:
Critical
Description:
Upper Critical - Going High - Asserted
Message:
DIMM Group% temperature is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Check Fan status. if Fan is broken, please replace the new Fan.
3. Contact your Lenovo service representative for support
Diagnostic Code:
0101072A
0101072B
Full Sensor Name (Sensor Name In SDR):
DIMMG%_Temp (% = Group number)
Sensor Type:
Temperature
Event Severity:
Warning
Description:
Upper Non-Critical - Going High - Asserted
Message:
DIMM Group% temperature is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Check Fan status. if Fan is broken, please replace the new Fan.
3. Contact your Lenovo service representative for support
Diagnostic Code:
01010B2C
01010B2D
01010B2E
01010B2F
Full Sensor Name (Sensor Name In SDR):
DIMM%_VR_Temp (% = Channel number)
Sensor Type:
Temperature
Event Severity:
Critical
Description:
Upper Non-Recoverable - Going High - Asserted
Message:
DIMM Group% VR temperature is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Check Fan status. if Fan is broken, please replace the new Fan.
3. Contact your Lenovo service representative for support
Diagnostic Code:
0101092C
0101092D
0101092E
0101092F
Full Sensor Name (Sensor Name In SDR):
DIMM%_VR_Temp (% = Channel number)
Sensor Type:
Temperature
Event Severity:
Critical
Description:
Upper Critical - Going High - Asserted
Message:
DIMM Group% VR temperature is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Check Fan status. if Fan is broken, please replace the new Fan.
3. Contact your Lenovo service representative for support
Diagnostic Code:
0101072C
0101072D
0101072E
0101072F
Full Sensor Name (Sensor Name In SDR):
DIMM%_VR_Temp (% = Channel number)
Sensor Type:
Temperature
Event Severity:
Warning
Description:
Upper Non-Critical - Going High - Asserted
Message:
DIMM Group% VR temperature is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Check Fan status. if Fan is broken, please replace the new Fan.
3. Contact your Lenovo service representative for support
Diagnostic Code:
0B010B91
Full Sensor Name (Sensor Name In SDR):
Node_IIN
Sensor Type:
Other Units-based sensor
Event Severity:
Critical
Description:
Upper Non-Recoverable - Going High - Asserted
Message:
Node input current is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
0B010991
Full Sensor Name (Sensor Name In SDR):
Node_IIN
Sensor Type:
Other Units-based sensor
Event Severity:
Critical
Description:
Upper Critical - Going High - Asserted
Message:
Node input current is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
0B010791
Full Sensor Name (Sensor Name In SDR):
Node_IIN
Sensor Type:
Other Units-based sensor
Event Severity:
Warning
Description:
Upper Non-Critical - Going High - Asserted
Message:
Node input current is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
0B010B92
Full Sensor Name (Sensor Name In SDR):
Node_IOUT
Sensor Type:
Other Units-based sensor
Event Severity:
Critical
Description:
Upper Non-Recoverable - Going High - Asserted
Message:
Node output current is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
0B010992
Full Sensor Name (Sensor Name In SDR):
Node_IOUT
Sensor Type:
Other Units-based sensor
Event Severity:
Critical
Description:
Upper Critical - Going High - Asserted
Message:
Node output current is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
0B010792
Full Sensor Name (Sensor Name In SDR):
Node_IOUT
Sensor Type:
Other Units-based sensor
Event Severity:
Warning
Description:
Upper Non-Critical - Going High - Asserted
Message:
Node output current is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
0B010093
Full Sensor Name (Sensor Name In SDR):
Node_VIN
Sensor Type:
Other Units-based sensor
Event Severity:
Warning
Description:
Lower Non-Critical - Going Low - Asserted
Message:
Node intput voltage is too low
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
0B010B93
Full Sensor Name (Sensor Name In SDR):
Node_VIN
Sensor Type:
Other Units-based sensor
Event Severity:
Critical
Description:
Upper Non-Recoverable - Going High - Asserted
Message:
Node intput voltage is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
0B010993
Full Sensor Name (Sensor Name In SDR):
Node_VIN
Sensor Type:
Other Units-based sensor
Event Severity:
Critical
Description:
Upper Critical - Going High - Asserted
Message:
Node intput voltage is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
0B010793
Full Sensor Name (Sensor Name In SDR):
Node_VIN
Sensor Type:
Other Units-based sensor
Event Severity:
Warning
Description:
Upper Non-Critical - Going High - Asserted
Message:
Node intput voltage is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
0B010094
Full Sensor Name (Sensor Name In SDR):
Node_VOUT
Sensor Type:
Other Units-based sensor
Event Severity:
Warning
Description:
Lower Non-Critical - Going Low - Asserted
Message:
Node output voltage is too low
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
0B010B94
Full Sensor Name (Sensor Name In SDR):
Node_VOUT
Sensor Type:
Other Units-based sensor
Event Severity:
Critical
Description:
Upper Non-Recoverable - Going High - Asserted
Message:
Node output voltage is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
0B010994
Full Sensor Name (Sensor Name In SDR):
Node_VOUT
Sensor Type:
Other Units-based sensor
Event Severity:
Critical
Description:
Upper Critical - Going High - Asserted
Message:
Node output voltage is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
0B010794
Full Sensor Name (Sensor Name In SDR):
Node_VOUT
Sensor Type:
Other Units-based sensor
Event Severity:
Warning
Description:
Upper Non-Critical - Going High - Asserted
Message:
Node output voltage is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
0B010B95
Full Sensor Name (Sensor Name In SDR):
Node_PIN
Sensor Type:
Other Units-based sensor
Event Severity:
Critical
Description:
Upper Non-Recoverable - Going High - Asserted
Message:
Node input power is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
0B010995
Full Sensor Name (Sensor Name In SDR):
Node_PIN
Sensor Type:
Other Units-based sensor
Event Severity:
Critical
Description:
Upper Critical - Going High - Asserted
Message:
Node input power is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
0B010795
Full Sensor Name (Sensor Name In SDR):
Node_PIN
Sensor Type:
Other Units-based sensor
Event Severity:
Warning
Description:
Upper Non-Critical - Going High - Asserted
Message:
Node input power is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
0B010B96
Full Sensor Name (Sensor Name In SDR):
Node_POUT
Sensor Type:
Other Units-based sensor
Event Severity:
Critical
Description:
Upper Non-Recoverable - Going High - Asserted
Message:
Node output power is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
0B010996
Full Sensor Name (Sensor Name In SDR):
Node_POUT
Sensor Type:
Other Units-based sensor
Event Severity:
Critical
Description:
Upper Critical - Going High - Asserted
Message:
Node output power is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
0B010796
Full Sensor Name (Sensor Name In SDR):
Node_POUT
Sensor Type:
Other Units-based sensor
Event Severity:
Warning
Description:
Upper Non-Critical - Going High - Asserted
Message:
Node output power is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
0B010B9A
Full Sensor Name (Sensor Name In SDR):
CPU_Power
Sensor Type:
Other Units-based sensor
Event Severity:
Critical
Description:
Upper Non-Recoverable - Going High - Asserted
Message:
CPU power consumption is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
0B01099A
Full Sensor Name (Sensor Name In SDR):
CPU_Power
Sensor Type:
Other Units-based sensor
Event Severity:
Critical
Description:
Upper Critical - Going High - Asserted
Message:
CPU power consumption is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
0201049C
Full Sensor Name (Sensor Name In SDR):
BAT_Volt
Sensor Type:
Voltage
Event Severity:
Critical
Description:
Lower Non-Recoverable - Going Low - Asserted
Message:
Battery voltage is too low
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
0201029C
Full Sensor Name (Sensor Name In SDR):
BAT_Volt
Sensor Type:
Voltage
Event Severity:
Critical
Description:
Lower Critical - Going Low - Asserted
Message:
Battery voltage is too low
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
0201009C
Full Sensor Name (Sensor Name In SDR):
BAT_Volt
Sensor Type:
Voltage
Event Severity:
Warning
Description:
Lower Non-Critical - Going Low - Asserted
Message:
Battery voltage is too low
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
086F06A0
Full Sensor Name (Sensor Name In SDR):
PSU_Mismatch
Sensor Type:
Power Supply
Event Severity:
Critical
Description:
Configuration Error - Asserted
Message:
There are different capacity or voltage of PSUs that are plugged in chassis.
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Restart the server.
3. Suggest to use the same type of PSUs. 4. Contact your Lenovo service representative for support
Diagnostic Code:
086F00A1
086F00A2
Full Sensor Name (Sensor Name In SDR):
PSU%_Status (% = PSU number)
Sensor Type:
Power Supply
Event Severity:
Critical
Description:
Presence detected - Deasserted
Message:
PSU is unplugged
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Check PSU is unpluged or not. If yes, please plug PSU back.
3. Contact your Lenovo service representative for support
Diagnostic Code:
086F01A1
086F01A2
Full Sensor Name (Sensor Name In SDR):
PSU%_Status (% = PSU number)
Sensor Type:
Power Supply
Event Severity:
Critical
Description:
Power Supply Failure detected - Asserted
Message:
PSU is OCP or OVP
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
086F03A1
086F03A2
Full Sensor Name (Sensor Name In SDR):
PSU%_Status (% = PSU number)
Sensor Type:
Power Supply
Event Severity:
Critical
Description:
Power Supply input lost (AC/DC) - Asserted
Message:
AC lost
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
0B010BA3
0B010BA4
Full Sensor Name (Sensor Name In SDR):
PSU%_POUT (% = PSU number)
Sensor Type:
Other Units-based sensor
Event Severity:
Critical
Description:
Upper Non-Recoverable - Going High - Asserted
Message:
PSU output power is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
0B0109A3
0B0109A4
Full Sensor Name (Sensor Name In SDR):
PSU%_POUT (% = PSU number)
Sensor Type:
Other Units-based sensor
Event Severity:
Critical
Description:
Upper Critical - Going High - Asserted
Message:
PSU output power is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
01010BA5
01010BA6
Full Sensor Name (Sensor Name In SDR):
PSU%_Temp (% = PSU number)
Sensor Type:
Temperature
Event Severity:
Critical
Description:
Upper Non-Recoverable - Going High - Asserted
Message:
PSU ambient temperature is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
010109A5
010109A6
Full Sensor Name (Sensor Name In SDR):
PSU%_Temp (% = PSU number)
Sensor Type:
Temperature
Event Severity:
Critical
Description:
Upper Critical - Going High - Asserted
Message:
PSU ambient temperature is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
040104A7
040104A8
Full Sensor Name (Sensor Name In SDR):
PSU%_FAN_Speed (% = PSU number)
Sensor Type:
Fan
Event Severity:
Critical
Description:
Lower Non-Recoverable - Going Low - Asserted
Message:
PSU FAN speed is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
04010BA7
04010BA8
Full Sensor Name (Sensor Name In SDR):
PSU%_FAN_Speed (% = PSU number)
Sensor Type:
Fan
Event Severity:
Critical
Description:
Upper Non-Recoverable - Going High - Asserted
Message:
PSU FAN speed is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
0B010BAA
Full Sensor Name (Sensor Name In SDR):
FAN_BP_Power
Sensor Type:
Other Units-based sensor
Event Severity:
Critical
Description:
Upper Non-Recoverable - Going High - Asserted
Message:
FAN backplane power consumption is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
0B010BAB
Full Sensor Name (Sensor Name In SDR):
HDD_BP_Power
Sensor Type:
Other Units-based sensor
Event Severity:
Critical
Description:
Upper Non-Recoverable - Going High - Asserted
Message:
HDD backplane power consumption is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
0B0109AB
Full Sensor Name (Sensor Name In SDR):
HDD_BP_Power
Sensor Type:
Other Units-based sensor
Event Severity:
Critical
Description:
Upper Critical - Going High - Asserted
Message:
HDD backplane power consumption is too high
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
160901C0
Full Sensor Name (Sensor Name In SDR):
BMC_Boot_Up
Sensor Type:
Microcontroller / Coprocessor
Event Severity:
Info
Description:
Device Enabled - Asserted
Message:
BMC boot up successfully.
Actions:
It is just an information. Users don't need to do anything.
Diagnostic Code:
226F00C1
Full Sensor Name (Sensor Name In SDR):
ACPI_PWR_Status
Sensor Type:
System ACPI Power
Event Severity:
Info
Description:
S0/G0 'working - Asserted
Message:
The system is under S0 state.
Actions:
It is just an information. Users don't need to do anything.
Diagnostic Code:
226F05C1
Full Sensor Name (Sensor Name In SDR):
ACPI_PWR_Status
Sensor Type:
System ACPI Power
Event Severity:
Info
Description:
S5/G2 - soft-off - Asserted
Message:
The system is under S5 state.
Actions:
It is just an information. Users don't need to do anything.
Diagnostic Code:
146F00C2
Full Sensor Name (Sensor Name In SDR):
Button_Status
Sensor Type:
Button / Switch
Event Severity:
Info
Description:
Power Button pressed - Asserted
Message:
Someone pressed the power button
Actions:
It is just an information. Users don't need to do anything.
Diagnostic Code:
106F02C3
Full Sensor Name (Sensor Name In SDR):
SEL_Status
Sensor Type:
Event Logging Disabled
Event Severity:
Info
Description:
Log Area Reset/Cleared - Asserted
Message:
The log area of SEL is cleared.
Actions:
It is just an information. Users don't need to do anything.
Diagnostic Code:
106F05C3
Full Sensor Name (Sensor Name In SDR):
SEL_Status
Sensor Type:
Event Logging Disabled
Event Severity:
Info
Description:
SEL Almost Full - Asserted
Message:
The SEL is almost full.
Actions:
It is just an information. Users don't need to do anything.
Diagnostic Code:
236F00C4
Full Sensor Name (Sensor Name In SDR):
IPMI_Watchdog
Sensor Type:
Watchdog 2
Event Severity:
Critical
Description:
Time expired - status only (no action and no interrupt) - Asserted
Message:
The watchdog timer is expired.
Actions:
It is just an information. Users don't need to do anything.
Diagnostic Code:
236F01C4
Full Sensor Name (Sensor Name In SDR):
IPMI_Watchdog
Sensor Type:
Watchdog 2
Event Severity:
Critical
Description:
Hard Reset - Asserted
Message:
The Hard Reset is triggered by watchdog.
Actions:
It is just an information. Users don't need to do anything.
Diagnostic Code:
236F02C4
Full Sensor Name (Sensor Name In SDR):
IPMI_Watchdog
Sensor Type:
Watchdog 2
Event Severity:
Critical
Description:
Power Down - Asserted
Message:
The Power Down is triggerred by watchdog.
Actions:
It is just an information. Users don't need to do anything.
Diagnostic Code:
236F03C4
Full Sensor Name (Sensor Name In SDR):
IPMI_Watchdog
Sensor Type:
Watchdog 2
Event Severity:
Critical
Description:
Power Cycle - Asserted
Message:
The Power Cycle is triggered by watchdog.
Actions:
It is just an information. Users don't need to do anything.
Diagnostic Code:
076F01C5
076F01C6
Full Sensor Name (Sensor Name In SDR):
CPU%_Status (% = CPU number)
Sensor Type:
Processor
Event Severity:
Critical
Description:
Thermal Trip - Asserted
Message:
CPU temperature is too high. At the same time, system will be shutdown.
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Check Fan status. if Fan is broken, please replace the new Fan.
3. Contact your Lenovo service representative for support
Diagnostic Code:
070301C7
Full Sensor Name (Sensor Name In SDR):
PROC_Hot
Sensor Type:
Processor
Event Severity:
Warning
Description:
State Asserted - Asserted
Message:
CPU begins to throttle because its temperature is too high.
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
076F0AC7
Full Sensor Name (Sensor Name In SDR):
PROC_Hot
Sensor Type:
Processor
Event Severity:
Warning
Description:
Processor Automatically Throttled - Asserted
Message:
CPU begins to throttle which is triggered by PSU alert.
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Contact your Lenovo service representative for support
Diagnostic Code:
CF6F00C9
Full Sensor Name (Sensor Name In SDR):
Chassis_Control
Sensor Type:
Customer Sensor Type
Event Severity:
Info
Description:
Chassis Control - Asserted
Message:
BMC gets Chassis Control command.
Actions:
It is just an information. Users don't need to do anything.
Diagnostic Code:
070301D0
Full Sensor Name (Sensor Name In SDR):
CPU_CATERR
Sensor Type:
Processor
Event Severity:
Critical
Description:
State Asserted - Asserted
Message:
Catastrophic error happened.
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Restart the server.
3. Contact your Lenovo service representative for support
Diagnostic Code:
070301D1
Full Sensor Name (Sensor Name In SDR):
CPU_VR_Fault
Sensor Type:
Processor
Event Severity:
Critical
Description:
State Asserted - Asserted
Message:
CPU VR fault.
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Restart the server.
3. Contact your Lenovo service representative for support
Diagnostic Code:
0C0301D2
Full Sensor Name (Sensor Name In SDR):
Mem_Therm_Trip
Sensor Type:
Memory
Event Severity:
Critical
Description:
State Asserted - Asserted
Message:
Memory temperature is too high. At the same time, system will be shutdown.
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Check Fan status. if Fan is broken, please replace the new Fan.
3. Contact your Lenovo service representative for support
Diagnostic Code:
196F01D3
Full Sensor Name (Sensor Name In SDR):
PCH_Therm_Trip
Sensor Type:
Chipset
Event Severity:
Critical
Description:
Thermal Trip - Asserted
Message:
PCH temperature is too high. At the same time, system will be shutdown.
Actions:
1. Check the Lenovo support website for an applicable retain tip or firmware update that applies to this error.
2. Check Fan status. if Fan is broken, please replace the new Fan.
3. Contact your Lenovo service representative for support
Diagnostic Code:
0D6F01D4
Full Sensor Name (Sensor Name In SDR):
HDD_Status
Sensor Type:
Drive Slot (Bay)
Event Severity:
Critical
Description:
Drive Fault - Asserted
Message:
HDD fault.
Actions:
1. Check Lenovo support site for an applicable service bulletin or firmware update that applies to this error.
2. Replace HDD.
3. Contact your Lenovo service representative for support.
Diagnostic Code:
1D6F02E0
Full Sensor Name (Sensor Name In SDR):
BIOS_Boot_up
Sensor Type:
System Boot / Restart Initiated
Event Severity:
Info
Description:
Initiated by warm reset - Asserted
Message:
BIOS boot up and it's initiated by warm reset.
Actions:
It is just an information. Users don't need to do anything.
Diagnostic Code:
0C6F00E2
Full Sensor Name (Sensor Name In SDR):
Memory_Status
Sensor Type:
Memory
Event Severity:
Critical
Description:
Correctable ECC or other correctable memory error - Asserted
Message:
A single bit error is occurred In memory. This error will be repaired automatically.
Actions:
1. If the node has recently been installed, moved, serviced, or upgraded, verify that the DIMM is properly seated and visually verify that there is no foreign material in any DIMM connector on that memory channel. If either of these conditions is found, correct and retry with the same DIMM
2. If problem re-occurs on the same DIMM connector, swap the other DIMMs on the same memory channel across channels one at a time to a different memory channel or Processor. (check service information for this product/Install guide for population requirements for sparing/paring modes). If problem follows a moved DIMM to a different memory channel, replace that DIMM.
Diagnostic Code:
0C6F01E2
Full Sensor Name (Sensor Name In SDR):
Memory_Status
Sensor Type:
Memory
Event Severity:
Critical
Description:
Uncorrectable ECC or other uncorrectable memory error - Asserted
Message:
A multiple bits error is occurred in memory. This error will cause system to be hang up.
Actions:
1. Check the Lenovo support website for an applicable service bulletin or firmware update that applies to this memory error.
2. If the node has recently been installed, moved, serviced, or upgraded, verify that the DIMM is properly seated and visually verify that there is no foreign material in any DIMM connector on that memory channel. If either of these conditions is found, correct and retry with the same DIMM.
3. If no problem is observed on the DIMM connectors and the problem persists, replace the DIMM identified by LightPath and/or event log entry. 4. If problem re-occurs on the same DIMM connector, swap the other DIMMs on the same memory channel across channels one at a time to a different memory channel or Processor. (check service information for this product/Install guide for population requirements for sparing/paring modes). If problem follows a moved DIMM to a different memory channel, replace that DIMM. 5. (Trained service technician only) Remove affected Processor and inspect Processor socket pins for damaged or mis-aligned pins. If damage is found, or this is an upgrade Processor, replace the system board. If there are multiple Processor’s, swap Processor’s to move affected Procesor to another Processor socket and retry. If problem follows the affected Processor (or there is only one Processor), replace the affected Processor. 6. (Trained technician only)If problem stays with the original DIMM connector, re-inspect DIMM connector for foreign material and remove, if found. If connector is damaged, replace system board
Diagnostic Code:
0C6F04E2
Full Sensor Name (Sensor Name In SDR):
Memory_Status
Sensor Type:
Memory
Event Severity:
Critical
Description:
Memory Device Disabled - Asserted
Message:
Memory fault occurs and it's disabled by BIOS.
Actions:
1. If the DIMM was disabled because of a memory fault, follow the procedure for that event.
2. If problem persists, Power cycle the node from management console.
3. Reset UEFI to default settings. 4. Swap/reseat the DIMM from the disabled slot with a matching DIMM. If the slot remains disabled, (trained technician only) replace system board
Diagnostic Code:
296F00E3
Full Sensor Name (Sensor Name In SDR):
Battery_Status
Sensor Type:
Battery
Event Severity:
Warning
Description:
battery low (predictive failure) - Asserted
Message:
The battery is too low.
Actions:
1. If the system was recently installed, moved, or serviced, make sure the battery is properly seated.
2. Check Lenovo support site for an applicable service bulletin or firmware update that applies to this error.
3. Replace CMOS battery. 4. (Trained technician only) Replace the system board.
Diagnostic Code:
126F05E4
Full Sensor Name (Sensor Name In SDR):
Timestamp
Sensor Type:
System Event
Event Severity:
Info
Description:
Timestamp Clock Synch - Asserted
Message:
The system time in BMC was synchronized with BIOS.
Actions:
It is just an information. Users don't need to do anything.
Diagnostic Code:
1E6F03E5
Full Sensor Name (Sensor Name In SDR):
Device_OPROM
Sensor Type:
Boot Error
Event Severity:
Warning
Description:
Invalid boot sector - Asserted
Message:
Optoin ROMs are full in memory space.
Actions:
Check the Lenovo support website for any applicable service bulletin or UEFI or adapter firmware update that applies to this error. Note: It may be necessary to disable unused option ROMs from BIOS setup.
Diagnostic Code:
136F07E6
Full Sensor Name (Sensor Name In SDR):
PCIE_Status
Sensor Type:
Critical Interrupt
Event Severity:
Critical
Description:
Bus Correctable Error - Asserted
Message:
A single bit error is occurred in PCIe bus. This error will be repaired automatically.
Actions:
If this node and/or any attached cables were recently installed, moved, serviced or upgraded, a. Reset adapter and any attached cables. b. Reload Device Driver. c. If device is not recognized, reconfiguring slot to Gen1 or Gen2 may be required. Gen1/Gen2 settings can be configured via F1 Setup -> System Settings -> Devices and I/O Ports -> PCIe Gen1/Gen2/Gen3 Speed Selection, or te ASU Utility.
Diagnostic Code:
136F08E6
Full Sensor Name (Sensor Name In SDR):
PCIE_Status
Sensor Type:
Critical Interrupt
Event Severity:
Critical
Description:
Bus Uncorrectable Error - Asserted
Message:
A multiple bits error is occurred in PCIe bus. This error will cause system to be hang up.
Actions:
1. Check the Lenovo support website for an applicable device driver, firmware update, version of service information for this product or other information that applies to this error. Load new device driver and any required firmware updates.
2. if this node and/or any attached cables were recently installed, moved, serviced or upgraded, a. Reset adapter and any attached cables. b. Reload Device Driver. c. If device is not recognized, reconfiguring slot to Gen1 or Gen2 may be required. Gen1/Gen2 settings can be configured via F1 Setup -> System Settings -> Devices and I/O Ports -> PCIe Gen1/Gen2/Gen3 Speed Selection, or te ASU Utility.
3. If problem persists, then remove Adapter Card. If system reboots successfully without the adapter, replace that card.