Skip to main content

Parts listing

Identify each of the components that are available for your solution with the parts listing.

For more information about ordering the parts:

  1. Go to Lenovo Data Center Support and navigate to the support page for your solution.

  2. Click Service Parts.

  3. Enter the serial number to view a listing of parts for your solution.

The parts listed in the following table are identified as one of the following:

  • Tier 1 customer replaceable unit (CRU): Replacement of Tier 1 CRUs is your responsibility. If Lenovo installs a Tier 1 CRU at your request with no service agreement, you will be charged for the installation.

  • Tier 2 customer replaceable unit (CRU): You may install a Tier 2 CRU yourself or request Lenovo to install it, at no additional charge, under the type of warranty service that is designated for your solution.

  • Field replaceable unit (FRU): FRUs must be installed only by trained service technicians.

  • Consumable parts: Purchase and replacement of consumable is your responsibility. If Lenovo acquires or installs a consumable component at your request, you will be charged for the service.

Note
Depending on the model, your solution might look slightly different from the illustration.

Enclosure components​

Figure 1. Enclosure components
Enclosure components
Table 1. Parts list
IndexDescriptionTier 1 CRUTier 2 CRUFRUConsumable and Structural part

For more information about ordering the parts shown in Enclosure components:

Enclosure parts

It is highly recommended that you check the power summary data for your server using Lenovo Capacity Planner before purchasing any new parts.

16U enclosure assembly  √ 
2Lift handle  √ 
3Upper EMC shield  √ 
4Lower EMC shield  √ 
5Manifold assembly  √ 
6Drip sensor tray  √ 
7Drip sensor assembly  √ 
8System Management Module 2  √ 
9Power supply√   
10Midplane  √ 
11External LCD diagnostics handset√   

SD650 V2 components​

Figure 2. SD650 V2 components
SD650 V2 components
Table 2. Parts list
IndexDescriptionTier 1 CRUTier 2 CRUFRUConsumable and Structural part

For more information about ordering the parts shown in SD650 V2 components:

Compute node parts

It is highly recommended that you check the power summary data for your server using Lenovo Capacity Planner before purchasing any new parts.

1Tray cover  √ 
2Rear cross brace  √ 
3Power distribution board  √ 
4Quick connects  √ 
5Quick connect plug covers  √ 
6Water loop  √ 
7DIMM comb  √ 
8DIMM tool  √ 
9DIMM  √ 
10DIMM VR clamp plate  √ 
11DIMM VR cold plate  √ 
12System board  √ 
13Processor  √ 
14Processor retainer  √ 
15Trusted Cryptographic Module (TCM)  √ 
16ConnectX-6 kit  √ 
17ConnectX-6 adapter  √ 
18Adapter  √ 
19PCIe riser cage  √ 
20Drive cage  √ 
212.5-inch drive (15mm)  √ 
222.5-inch drive (7mm)  √ 
23Front cross brace  √ 
24Blank bezel filler√   
25Water loop carrier  √ 
26SD650 V2 cam handles  √ 
27M.2 retainer clip  √ 
28M.2 backplane  √ 
29M.2 drive (42 mm and 80 mm)  √ 
30SD650 V2 tray  √ 
31CMOS battery (CR2032)   √
32DWC waterloop service kit  √ 
33SD650-N V2/ SD650-V2 Neptune DWC gap pad and putty kit  √ 
34Upper drive conduction plate assembly  √ 
35Heat sink peek nut  √ 
36Cable  √ 

SD650-N V2 components​

Figure 3. SD650-N V2 components
SD650-N V2 components
Table 3. Parts listing
IndexDescriptionTier 1 CRUTier 2 CRUFRUConsumable and Structural part

For more information about ordering the parts shown in SD650-N V2 components:

GPU node parts

It is highly recommended that you check the power summary data for your server using Lenovo Capacity Planner before purchasing any new parts.

1Tray cover  √ 
2GPU Power distribution board  √ 
3Power distribution board  √ 
4Rear cross brace  √ 
5Quick connects  √ 
6Quick connect plug covers  √ 
7Water loop  √ 
8DIMM comb  √ 
9DIMM tool  √ 
10DIMM  √ 
11DIMM VR clamp plate  √ 
12DIMM VR cold plate  √ 
13M.2 backplane  √ 
14M.2 drive (42 mm and 80 mm)  √ 
15M.2 retainer clip  √ 
16System board  √ 
17GPU board  √ 
18Processor  √ 
19Processor retainer  √ 
20Trusted Cryptographic Module (TCM)  √ 
21ConnectX-6 kit  √ 
22ConnectX-6 adapter  √ 
23Adapter  √ 
24PCIe riser cage  √ 
25Drive cage (for compute node)  √ 
262.5-inch drive (15mm)  √ 
272.5-inch drive (7mm)  √ 
28Front cross brace  √ 
29Blank bezel filler√   
30SD650-N V2 tray cam handles  √ 
31Retimer clamp plate
Note
The retimer clamp plate is available only if no drive is installed in the GPU node.
  √ 
32Drive cage (for GPU node)
Note
The drive cage is available only if the drive is installed in the GPU node.
  √ 
33Retimer board  √ 
34SD650-N V2 tray  √ 
35Compute node water loop carrier  √ 
36GPU node water loop carrier  √ 
37CMOS battery (CR2032)   √
38Neptune DWC Waterloop service kit  √ 
39SD650-N V2/ SD650-V2 Neptune DWC gap pad and putty kit  √ 
40Upper drive conduction plate assembly  √ 
41Heat sink peek nut  √ 
42GPU  √ 
43Cable  √ 
  • Power cords
    Several power cords are available, depending on the country and region where the server is installed.