UEFI events organized by severity
The following table lists all UEFI events, organized by severity (Information, Error, and Warning).
| Event ID | Message String | Severity |
|---|---|---|
| FQXSFDD0008I | Self-Encrypting Drive (SED) Error: recovered from failure to get key. | Informational |
| FQXSFDD0009I | Self-Encrypting Drive (SED) Error: recovered from failure to access drive [arg1]. | Informational |
| FQXSFDD0010I | Self-Encrypting Drive (SED) Error: recovered from failure to unlock drive [arg1]. | Informational |
| FQXSFDD0011I | Self-Encrypting Drive (SED) Error: recovered from failure to set password to drive [arg1]. | Informational |
| FQXSFDD0012I | SATA Hard Drive Error: [arg1] was recovered. | Informational |
| FQXSFIO0005I | An intra-board UPI has been disabled on the link between processor [arg1] port [arg2] and processor [arg3]port [arg4] because of UPI topology downgrade. | Informational |
| FQXSFIO0006I | An inter-board UPI has been disabled on the link between processor [arg1] port [arg2] and processor [arg3]port [arg4] because of UPI topology downgrade. | Informational |
| FQXSFIO0015I | IFM: System reset performed to reset adapters. | Informational |
| FQXSFIO0018I | IFM: Configuration too large for compatibility mode. | Informational |
| FQXSFIO0020J | PCIe Isolation has occurred in PCIe slot [arg1]. The adapter may not operate correctly. | Informational |
| FQXSFMA0001I | DIMM [arg1] Disable has been recovered. [arg2] | Informational |
| FQXSFMA0002I | The uncorrectable memory error state has been cleared. | Informational |
| FQXSFMA0006I | [arg1] DIMM [arg2] has been detected, the DIMM serial number is [arg3]. | Informational |
| FQXSFMA0007I | [arg1] DIMM number [arg2] has been replaced. [arg3] | Informational |
| FQXSFMA0008I | DIMM [arg1] POST memory test failure has been recovered. [arg2] | Informational |
| FQXSFMA0009I | Invalid memory configuration for Mirror Mode has been recovered. [arg1] | Informational |
| FQXSFMA0010I | Invalid memory configuration for Sparing Mode has been recovered. [arg1] | Informational |
| FQXSFMA0011I | Memory population change detected. [arg1] | Informational |
| FQXSFMA0012I | The PFA of DIMM [arg1] has been deasserted. | Informational |
| FQXSFMA0013I | Mirror Fail-over complete. DIMM [arg1] has failed over to to the mirrored copy. [arg2] | Informational |
| FQXSFMA0014I | Memory spare copy initiated. [arg1] | Informational |
| FQXSFMA0015I | Memory spare copy has completed successfully. [arg1] | Informational |
| FQXSFMA0026I | DIMM [arg1] Self-healing, attempt post package repair (PPR) succeeded at Rank [arg2] Sub Rank [arg3] Bank [arg4] Row [arg5] on Device [arg6]. [arg7] | Informational |
| FQXSFMA0029I | The PFA of DIMM [arg1] has been deasserted after applying PPR for this DIMM. [arg2] | Informational |
| FQXSFMA0046I | DIMM [arg1] is Intel Optane PMEM and its volatile or non-volatile capacity will be inaccessible because that configuration mode is not supported on current platform. | Informational |
| FQXSFMA0052I | DIMM [arg1] has been disabled due to the error on DIMM [arg2].[arg3] | Informational |
| FQXSFMA0065I | Multi-bit CE of DIMM [arg1] has been deasserted after performing post package repair. DIMM identifier is [arg2]. | Informational |
| FQXSFPU0020I | The UEFI firmware image capsule signature is invalid. | Informational |
| FQXSFPU0021I | The TPM physical presence state has been cleared. | Informational |
| FQXSFPU0023I | Secure Boot Image Verification Failure has been cleared as no failure in this round boot. | Informational |
| FQXSFPU0025I | The default system settings have been restored. | Informational |
| FQXSFPU4034I | TPM Firmware recovery is finished, rebooting system to take effect. | Informational |
| FQXSFPU4038I | TPM Firmware recovery successful. | Informational |
| FQXSFPU4041I | TPM Firmware update is in progress. Please DO NOT power off or reset system. | Informational |
| FQXSFPU4042I | TPM Firmware update is finished, rebooting system to take effect. | Informational |
| FQXSFPU4044I | The current TPM firmware version could not support TPM version toggling. | Informational |
| FQXSFPU4046I | TPM Firmware will be updated from TPM1.2 to TPM2.0. | Informational |
| FQXSFPU4047I | TPM Firmware will be updated from TPM2.0 to TPM1.2. | Informational |
| FQXSFPU4049I | TPM Firmware update successful. | Informational |
| FQXSFPU4059I | User requested to skip freezing lock of AHCI-attached SATA drives. System UEFI accepted the request and will execute prior to OS boot. | Informational |
| FQXSFPU4060I | Skipped freezing lock of AHCI-attached SATA drives. | Informational |
| FQXSFPU4061I | Restored default locking behavior of AHCI-attached SATA drives. | Informational |
| FQXSFPU4080I | Host Power-On password has been changed. | Informational |
| FQXSFPU4081I | Host Power-On password has been cleared. | Informational |
| FQXSFPU4082I | Host Admin password has been changed. | Informational |
| FQXSFPU4083I | Host Admin password has been cleared. | Informational |
| FQXSFPU4084I | Host boot order has been changed. | Informational |
| FQXSFPU4085I | Host WOL boot order has been changed. | Informational |
| FQXSFSM0007I | The XCC System Event log (SEL) is full. | Informational |
| FQXSFSR0002I | [arg1] GPT corruption recovered, DiskGUID: [arg2] | Informational |
| FQXSFDD0001G | DRIVER HEALTH PROTOCOL: Missing Configuration. Requires Change Settings From F1. | Warning |
| FQXSFDD0002M | DRIVER HEALTH PROTOCOL: Reports 'Failed' Status Controller. | Warning |
| FQXSFDD0003I | DRIVER HEALTH PROTOCOL: Reports 'Reboot' Required Controller. | Warning |
| FQXSFDD0005M | DRIVER HEALTH PROTOCOL: Disconnect Controller Failed. Requires 'Reboot'. | Warning |
| FQXSFDD0006M | DRIVER HEALTH PROTOCOL: Reports Invalid Health Status Driver. | Warning |
| FQXSFDD0007G | Security Key Lifecycle Manager (SKLM) IPMI Error. | Warning |
| FQXSFIO0008M | An intra-board UPI dynamic link width reduction has been detected on the link between processor [arg1] port [arg2] and processor [arg3] port [arg4]. | Warning |
| FQXSFIO0009M | An inter-board UPI dynamic link width reduction has been detected on the link between processor [arg1] port [arg2] and processor [arg3] port [arg4]. | Warning |
| FQXSFIO0013I | The device found at Bus [arg1] Device [arg2] Function [arg3] could not be configured due to resource constraints. The Vendor ID for the device is [arg4] and the Device ID is [arg5]. The physical slot number is [arg6]. | Warning |
| FQXSFIO0016M | IFM: Reset loop avoided - Multiple resets not allowed. | Warning |
| FQXSFIO0021J | PCIe Error Recovery has occurred in physical [arg1] number [arg2]. The [arg3] may not operate correctly. | Warning |
| FQXSFIO0022J | PCIe Link Width has degraded from [arg1] to [arg2] in physical [arg3] number [arg4]. | Warning |
| FQXSFIO0023J | PCIe Link Speed has degraded from [arg1] to [arg2] in physical [arg3] number [arg4]. | Warning |
| FQXSFIO0032M | PCIe Correctable Error PFA Threshold limit has been exceeded at Bus [arg1] Device [arg2] Function [arg3]. The Vendor ID for the device is [arg4] and the Device ID is [arg5]. The physical bay number is [arg6]. | Warning |
| FQXSFIO0033J | PCIe Link Width has degraded from [arg1] to [arg2] in physical bay number [arg3]. | Warning |
| FQXSFIO0034J | PCIe Link Speed has degraded from [arg1] to [arg2] in physical bay number [arg3]. | Warning |
| FQXSFMA0012L | The [arg1] PFA Threshold limit has been exceeded on DIMM [arg2] at address [arg3]. [arg4] | Warning |
| FQXSFMA0016M | Memory spare copy failed. [arg1] | Warning |
| FQXSFMA0026G | Multi-bit CE occurred on DIMM [arg1], need to restart the system for DIMM Self-healing to attempt post package repair (PPR). | Warning |
| FQXSFMA0027M | DIMM [arg1] Self-healing, attempt post package repair (PPR) failed at Rank [arg2] Sub Rank [arg3] Bank [arg4] Row [arg5] on Device [arg6]. [arg7] | Warning |
| FQXSFMA0028M | DIMM [arg1] Self-healing, attempt post package repair (PPR) exceeded DIMM level threshold [arg2] at Rank [arg3] Sub Rank [arg4] Bank [arg5] Row [arg6] on Device [arg7]. [arg8] | Warning |
| FQXSFMA0030K | Intel Optane PMEM [arg1] Percentage Remaining is less than [arg2]% and still functioning. | Warning |
| FQXSFMA0031K | Intel Optane PMEM [arg1] has reached 1% remaining spares block and still functioning. | Warning |
| FQXSFMA0033M | Intel Optane PMEM persistent memory interleave set has [arg1] PMEMs(DIMM [arg2]), [arg3] DIMMs' location is not correct. | Warning |
| FQXSFMA0034M | DIMM [arg1] (UID: [arg2]) of Intel Optane PMEM persistent memory interleave set should be moved to DIMM slot [arg3] in sequence. | Warning |
| FQXSFMA0035M | Intel Optane PMEM interleave set should have [arg1] PMEMs, but [arg2] PMEMs are missing. | Warning |
| FQXSFMA0036M | DIMM [arg1] (UID: [arg2]) of Intel Optane PMEM persistent memory interleave set is missing. | Warning |
| FQXSFMA0037G | Intel Optane PMEM interleave set (DIMM [arg1]) is migrated from another system (Platform ID: [arg2]), these migrated PMEMs are not supported nor warranted in this system. | Warning |
| FQXSFMA0038K | All Intel Optane PMEMs could not be auto unlocked because of no passphrase. | Warning |
| FQXSFMA0039K | One or more Intel Optane PMEMs could not be auto unlocked because of invalid passphrase. | Warning |
| FQXSFMA0040K | Invalid Intel Optane PMEM configuration detected. Please verify PMEM configuration is valid. | Warning |
| FQXSFMA0041K | Near Memory/Far Memory ratio (1:[arg1].[arg2]) for Intel Optane PMEM configuration is not in recommended range (1:[arg3] - 1:[arg4]). | Warning |
| FQXSFMA0047M | SPD CRC checking failed on DIMM [arg1]. [arg2] | Warning |
| FQXSFMA0076M | DIMM [arg1] is not supported, DIMM identifier is [arg2]. | Warning |
| FQXSFPU0022G | The TPM configuration is not locked. | Warning |
| FQXSFPU0023G | Secure Boot Image Verification Failure Warning. | Warning |
| FQXSFPU0033G | Processor has been disabled. | Warning |
| FQXSFPU0062F | System uncorrected recoverable error happened in Processor [arg1] Core [arg2] MC bank [arg3] with MC Status [arg4], MC Address [arg5], and MC Misc [arg6]. | Warning |
| FQXSFPU4033F | TPM Firmware recovery is in progress. Please DO NOT power off or reset system. | Warning |
| FQXSFPU4035M | TPM Firmware recovery failed. TPM chip may be damaged. | Warning |
| FQXSFPU4040M | TPM selftest has failed. | Warning |
| FQXSFPU4043G | TPM Firmware update aborted. System is rebooting... | Warning |
| FQXSFPU4050G | Failed to update TPM Firmware. | Warning |
| FQXSFPU4051G | Undefined TPM_POLICY found | Warning |
| FQXSFPU4052G | TPM_POLICY is not locked | Warning |
| FQXSFPU4053G | System TPM_POLICY does not match the planar. | Warning |
| FQXSFPU4054G | TPM card logical binding has failed. | Warning |
| FQXSFPW0001L | CMOS has been cleared. | Warning |
| FQXSFSM0002N | Boot Permission denied by Management Module: System Halted. | Warning |
| FQXSFSM0003N | Timed Out waiting on boot permission from Management Module: System Halted. | Warning |
| FQXSFSM0004M | An XCC communication failure has occurred. | Warning |
| FQXSFSR0001M | [arg1] GPT corruption detected, DiskGUID: [arg2] | Warning |
| FQXSFSR0003G | The number of boot attempts has been exceeded. No bootable device found. | Warning |
| FQXSFTR0001L | An invalid date and time have been detected. | Warning |
| FQXSFDD0004M | DRIVER HEALTH PROTOCOL: Reports 'System Shutdown' Required Controller. | Error |
| FQXSFDD0008K | Self-Encrypting Drive (SED) Error: failed to get key. | Error |
| FQXSFDD0009K | Self-Encrypting Drive (SED) Error: failed to access drive [arg1]. | Error |
| FQXSFDD0010K | Self-Encrypting Drive (SED) Error: failed to unlock drive [arg1]. | Error |
| FQXSFDD0011K | Self-Encrypting Drive (SED) Error: failed to set password to drive [arg1]. | Error |
| FQXSFDD0012K | SATA Hard Drive Error: [arg1]. | Error |
| FQXSFIO0005M | An intra-board UPI failure has been detected on the link between processor [arg1] port [arg2] and processor [arg3] port [arg4]. | Error |
| FQXSFIO0006M | An inter-board UPI failure has been detected on the link between processor [arg1] port [arg2] and processor [arg3] port [arg4]. | Error |
| FQXSFIO0007M | An error has been detected by the IIO on Bus [arg1]. The value of Global Fatal Error Status register is [arg2]. The value of Global Non-Fatal Error Status register is [arg3]. Please check error logs for additional downstream device error data. | Error |
| FQXSFIO0010M | An Uncorrectable PCIe Error has Occurred at Bus [arg1] Device [arg2] Function [arg3]. The Vendor ID for the device is [arg4] and the Device ID is [arg5]. The physical [arg6] number is [arg7]. | Error |
| FQXSFIO0011M | A PCIe parity error has occurred on Bus [arg1] Device [arg2] Function [arg3]. The Vendor ID for the device is [arg4] and the Device ID is [arg5]. The Physical slot number is [arg6]. | Error |
| FQXSFIO0012M | A PCIe system error has occurred on Bus [arg1] Device [arg2] Function [arg3]. The Vendor ID for the device is [arg4] and the Device ID is [arg5]. The Physical slot number is [arg6]. | Error |
| FQXSFIO0014J | A bad option ROM checksum was detected for the device found at Bus [arg1] Device [arg2] Function [arg3]. The Vendor ID for the device is [arg4] and the Device ID is [arg5]. The physical slot number is [arg6]. | Error |
| FQXSFIO0017M | IFM: Error communicating with the XCC - IFM may not be deployed correctly. | Error |
| FQXSFIO0019J | PCIe Resource Conflict. | Error |
| FQXSFIO0031M | An Uncorrectable PCIe Error has Occurred at Bus [arg1] Device [arg2] Function [arg3]. The Vendor ID for the device is [arg4] and the Device ID is [arg5]. The physical bay number is [arg6]. | Error |
| FQXSFMA0001M | DIMM [arg1] has been disabled due to an error detected during POST. [arg2] | Error |
| FQXSFMA0002M | An uncorrectable memory error has been detected on DIMM [arg1] at address [arg2]. [arg3] | Error |
| FQXSFMA0003K | A memory mismatch has been detected. Please verify that the memory configuration is valid. [arg1] | Error |
| FQXSFMA0004N | No system memory has been detected. [arg1] | Error |
| FQXSFMA0005N | Memory is present within the system but could not be configured. Please verify that the memory configuration is valid. [arg1] | Error |
| FQXSFMA0008M | DIMM [arg1] has failed the POST memory test. [arg2] | Error |
| FQXSFMA0009K | Invalid memory configuration for Mirror Mode. Please correct memory configuration. [arg1] | Error |
| FQXSFMA0010K | Invalid memory configuration for Sparing Mode. Please correct memory configuration. [arg1] | Error |
| FQXSFMA0023M | Error has occurred in NVDIMM flash. NVDIMM backup/restore may not operate correctly. [arg1] | Error |
| FQXSFMA0024M | Error has occurred in NVDIMM Supercap. NVDIMM backup/restore may not operate correctly. [arg1] | Error |
| FQXSFMA0025M | NVDIMM Supercap has been disconnected. NVDIMM will lose its backup ability until this is corrected. [arg1] | Error |
| FQXSFMA0027K | Invalid memory configuration (Unsupported DIMM Population) detected. Please verify memory configuration is valid. | Error |
| FQXSFMA0028K | Memory Capacity exceeds CPU limit. [arg1] | Error |
| FQXSFMA0032M | Intel Optane PMEM [arg1] has no remaining spares block. | Error |
| FQXSFMA0042K | Intel Optane PMEM is not supported by processor of this system. | Error |
| FQXSFMA0046M | DIMM [arg1] is disabled because it is Intel Optane PMEM that is not supported on current platform | Error |
| FQXSFPU0001N | An unsupported processor has been detected. | Error |
| FQXSFPU0002N | An invalid processor type has been detected. | Error |
| FQXSFPU0003K | A processor mismatch has been detected between one or more processors in the system. | Error |
| FQXSFPU0004K | A discrepancy has been detected in the number of cores reported by one or more processors within the system. | Error |
| FQXSFPU0005K | A mismatch between the maximum allowed UPI link speed has been detected for one or more processors. | Error |
| FQXSFPU0006K | A power segment mismatch has been detected for one or more processors. | Error |
| FQXSFPU0007K | Processors have mismatched Internal DDR Frequency | Error |
| FQXSFPU0008K | A core speed mismatch has been detected for one or more processors. | Error |
| FQXSFPU0009K | An external clock frequency mismatch has been detected for one or more processors. | Error |
| FQXSFPU0010K | A cache size mismatch has been detected for one or more processors. | Error |
| FQXSFPU0011K | A cache type mismatch has been detected for one or more processors. | Error |
| FQXSFPU0012K | A cache associativity mismatch has been detected for one or more processors. | Error |
| FQXSFPU0013K | A processor model mismatch has been detected for one or more processors. | Error |
| FQXSFPU0014N | A processor family mismatch has been detected for one or more processors. | Error |
| FQXSFPU0015K | A processor stepping mismatch has been detected for one or more processors. | Error |
| FQXSFPU0016N | A processor within the system has failed the BIST. | Error |
| FQXSFPU0017G | A processor microcode update failed. | Error |
| FQXSFPU0018N | CATERR(IERR) has asserted on processor [arg1]. | Error |
| FQXSFPU0019N | An uncorrectable error has been detected on processor [arg1]. | Error |
| FQXSFPU0027N | System uncorrectable error has occurred on Processor [arg1] Core [arg2] MC bank [arg3] with MC Status [arg4], MC Address [arg5], and MC Misc [arg6]. | Error |
| FQXSFPU0030N | A firmware fault has been detected in the UEFI image. | Error |
| FQXSFPU0031N | The number of POST attempts has reached the value configured in F1 setup. The system has booted with default UEFI settings. User specified settings have been preserved and will be used on subsequent boots unless modified before rebooting. | Error |
| FQXSFPU0034L | The TPM could not be initialized properly. | Error |
| FQXSFPU0035N | A 3-strike timeout has occurred on processor [arg1]. | Error |
| FQXSFPU4056M | TPM card is changed, need install back the original TPM card which shipped with the system. | Error |
| FQXSFSM0008M | Boot permission timeout detected. | Error |
Give documentation feedback