UEFI events organized by severity
The following table lists all UEFI events, organized by severity (Information, Error, and Warning).
| Event ID | Message String | Severity |
|---|---|---|
| FQXSFIO0005I | An intra-board UPI has been disabled on the link between processor [arg1] port [arg2] and processor [arg3]port [arg4] because of UPI topology downgrade. | Informational |
| FQXSFIO0006I | An inter-board UPI has been disabled on the link between processor [arg1] port [arg2] and processor [arg3]port [arg4] because of UPI topology downgrade. | Informational |
| FQXSFIO0021I | PCIe DPC software triggering occurred in physical [arg1] number [arg2]. | Informational |
| FQXSFMA0001I | DIMM [arg1] Disable has been recovered. [arg2] | Informational |
| FQXSFMA0006I | [arg1] DIMM [arg2] has been detected, the DIMM serial number is [arg3]. | Informational |
| FQXSFMA0007I | [arg1] DIMM number [arg2] has been replaced. [arg3] | Informational |
| FQXSFMA0008I | DIMM [arg1] POST memory test failure has been recovered. [arg2] | Informational |
| FQXSFMA0009I | Invalid memory configuration for Mirror Mode has been recovered. | Informational |
| FQXSFMA0026I | DIMM [arg1] Self-healing, attempt post-package repair (PPR) succeeded. [arg2] | Informational |
| FQXSFMA0027I | Invalid memory configuration (unsupported DIMM Population) recovered. | Informational |
| FQXSFMA0029I | The PFA of DIMM [arg1] has been deasserted after applying PPR for this DIMM. [arg2] | Informational |
| FQXSFMA0052I | DIMM [arg1] has been disabled due to the error on DIMM [arg2].[arg3] | Informational |
| FQXSFMA0053I | DIMM [arg1] re-enabled due to memory module combination updating. | Informational |
| FQXSFMA0056I | Uncorrected memory error occurred on DIMM [arg1] has been deasserted after performing post package repair. DIMM identifier is [arg2]. | Informational |
| FQXSFMA0063I | A correctable memory error handled by ADDDC on DIMM [arg1]. DIMM identifier is [arg2]. | Informational |
| FQXSFMA0065I | Multi-bit CE of DIMM [arg1] has been deasserted after performing post package repair. DIMM identifier is [arg2]. | Informational |
| FQXSFMA0067I | Errors per row counter threshold limit exceeded on DIMM [arg1] has been deasserted after performing post package repair. DIMM identifier is [arg2]. | Informational |
| FQXSFMA0079I | NVRAM [arg1] corruption detected and recovered. | Informational |
| FQXSFMA0080I | Runtime soft post package repair succeeded on DIMM [arg1].[arg2] | Informational |
| FQXSFMA0096I | Memory mode has been recovered to [arg1]. | Informational |
| FQXSFPU0025I | The default system settings have been restored. | Informational |
| FQXSFPU4034I | TPM Firmware recovery is finished, rebooting system to take effect. | Informational |
| FQXSFPU4038I | TPM Firmware recovery successful. | Informational |
| FQXSFPU4041I | TPM Firmware update is in progress. Please DO NOT power off or reset system. | Informational |
| FQXSFPU4042I | TPM Firmware update is finished, rebooting system to take effect. | Informational |
| FQXSFPU4044I | The current TPM firmware version could not support TPM version toggling. | Informational |
| FQXSFPU4062I | CPU debugging is deactivated. | Informational |
| FQXSFPU4080I | Host Power-On password has been changed. | Informational |
| FQXSFPU4081I | Host Power-On password has been cleared. | Informational |
| FQXSFPU4082I | Host Admin password has been changed. | Informational |
| FQXSFPU4083I | Host Admin password has been cleared. | Informational |
| FQXSFPU4084I | Host boot order has been changed. | Informational |
| FQXSFPU4092I | UEFI extra setting [arg1] is replaced by UEFI normal setting [arg2] after updating UEFI to [arg3]. | Informational |
| FQXSFPU4094I | UEFI extra settings exposure config file import successfully. | Informational |
| FQXSFPU4096I | UEFI extra settings exposure config file is deleted and all UEFI extra settings are unset. | Informational |
| FQXSFSR0002I | [arg1] GPT corruption recovered, DiskGUID: [arg2] | Informational |
| FQXSFSR0003I | Boot OS successfully. | Informational |
| FQXSFIO0008M | An intra-board UPI dynamic link width reduction has been detected on the link between processor [arg1] port [arg2] and processor [arg3] port [arg4]. | Warning |
| FQXSFIO0009M | An inter-board UPI dynamic link width reduction has been detected on the link between processor [arg1] port [arg2] and processor [arg3] port [arg4]. | Warning |
| FQXSFIO0021J | PCIe Error Recovery has occurred in physical [arg1] number [arg2]. The [arg3] may not operate correctly. | Warning |
| FQXSFIO0022J | PCIe Link Width has degraded from [arg1] to [arg2] in physical [arg3] number [arg4]. | Warning |
| FQXSFIO0023J | PCIe Link Speed has degraded from [arg1] to [arg2] in physical [arg3] number [arg4]. | Warning |
| FQXSFIO0024I | An error has been detected by the IEH on processor [arg1]. The type of IEH is [arg2]. The index of the IEH is [arg3]. The value of IehErrorStatus register is [arg4]. Please check error logs for additional downstream device error data. | Warning |
| FQXSFIO0025I | An error has been detected by the IIO on processor [arg1]. The index of the IIO stack is [arg2]. The type of IIO Internal Error is [arg3]. Please check error logs for additional downstream device error data. | Warning |
| FQXSFIO0036G | PCIe Correctable Error Threshold limit has been exceeded at Segment 0x[arg1] Bus 0x[arg2] Device 0x[arg3] Function 0x[arg4]. The Vendor ID for the device is 0x[arg5] and the Device ID is 0x[arg6]. The physical [arg7] number is [arg8]. | Warning |
| FQXSFIO0041J | PCIe Leaky Bucket Event : [arg1] occurred at Segment [arg2] Bus [arg3] Device [arg4] Function [arg5]. The physical [arg6] number is [arg7]. | Warning |
| FQXSFMA0026G | Multi-bit CE occurred on DIMM [arg1], need to restart the system for DIMM Self-healing to attempt post package repair (PPR).[arg2] | Warning |
| FQXSFMA0027G | Multi-bit CE occurred on DIMM [arg1] different rows.[arg2] | Warning |
| FQXSFMA0027M | DIMM [arg1] Self-healing, attempt post-package repair (PPR) failed. [arg2] | Warning |
| FQXSFMA0028M | The number of post-package repair (PPR) attempts has reached the limit on DIMM [arg1]. [arg2] | Warning |
| FQXSFMA0029G | DIMM [arg1] Self-healing, attempt post-package repair (PPR) failed: Spare rows for repair are out of resource. [arg2] | Warning |
| FQXSFMA0047M | SPD CRC checking failed on DIMM [arg1]. [arg2] | Warning |
| FQXSFMA0048M | DIMM [arg1] disabled due to PMIC failure during POST, DIMM identifier is [arg2]. | Warning |
| FQXSFMA0049M | DIMM [arg1] disabled due to memory module power failure. DIMM [arg2] detected and good, DIMM [arg3] not detected. | Warning |
| FQXSFMA0050G | DRAM PFA threshold limit exceeded on DIMM [arg1] sub-channel [arg2] Rank [arg3] DRAM [arg4], DIMM identifier is [arg5]. | Warning |
| FQXSFMA0053G | An uncorrected memory error has been recovered by mirror on DIMM [arg1] at address [arg2].[arg3] | Warning |
| FQXSFMA0053M | DIMM [arg1] not defective but disabled due to unsupported memory module combination on CPU [arg2]. | Warning |
| FQXSFMA0054G | Mirror failover operation was successful. DIMM [arg1] has failed over to the mirrored DIMM [arg2].[arg3] | Warning |
| FQXSFMA0055G | Mirror failover operation is skipped and page retire for uncorrectable error (at [arg1]) on DIMM [arg2] is reported to OS. [arg3] | Warning |
| FQXSFMA0057G | Page Retire PFA Threshold limit exceeded on DIMM [arg1] at address [arg2].[arg3] [arg4] | Warning |
| FQXSFMA0064M | DIMM [arg1] disabled due to memory module power failure. DIMM [arg2] detected and good. | Warning |
| FQXSFMA0067G | Errors per row counter threshold limit exceeded on DIMM [arg1] sub-channel [arg2] Rank [arg3] DRAM [arg4], need to restart the system for DIMM Self-healing to attempt post package repair (PPR), DIMM identifier is [arg5]. | Warning |
| FQXSFMA0076M | DIMM [arg1] is not supported, DIMM identifier is [arg2]. | Warning |
| FQXSFMA0081M | Runtime soft post package repair failed on DIMM [arg1], need to restart system to attempt boot time post package repair.[arg2] | Warning |
| FQXSFMA0094K | CMM device at Bay [arg1] is failed to be active. | Warning |
| FQXSFMA0095K | Current combination of DIMM and CMM devices does not fulfill the requirements of Heterogeneous Interleave. | Warning |
| FQXSFMA0096K | Force memory mode from Heterogeneous Interleave to 1LM + Vol. | Warning |
| FQXSFMA0097K | Force memory mode from Flat Memory Mode to 1LM + Vol. | Warning |
| FQXSFPU0023G | Secure Boot Image Verification Failure Warning. | Warning |
| FQXSFPU0039G | 3rd party option rom of PCIe physical [arg1] number [arg2] failed secure boot verification. | Warning |
| FQXSFPU0040G | Secure boot keys were reset to factory default. | Warning |
| FQXSFPU0062F | System uncorrected recoverable error happened in Processor [arg1] Core [arg2] MC bank [arg3] with MC Status [arg4], MC Address [arg5], and MC Misc [arg6]. | Warning |
| FQXSFPU4033F | TPM Firmware recovery is in progress. Please DO NOT power off or reset system. | Warning |
| FQXSFPU4035M | TPM Firmware recovery failed. TPM chip may be damaged. | Warning |
| FQXSFPU4040M | TPM selftest has failed. | Warning |
| FQXSFPU4050G | Failed to update TPM Firmware. | Warning |
| FQXSFPU4051G | Undefined TPM_POLICY found. | Warning |
| FQXSFPU4052G | TPM_POLICY is not locked. | Warning |
| FQXSFPU4053G | System TPM_POLICY does not match the planar. | Warning |
| FQXSFPU4062M | CPU debugging is activated. | Warning |
| FQXSFPU4086G | UEFI extra setting [arg1] is not found in current UEFI [arg2]. | Warning |
| FQXSFPU4087G | UEFI extra setting [arg1] value [arg2] is invalid in current UEFI [arg3]. | Warning |
| FQXSFPU4088G | Custom default[arg1] is not present, unable to append custom default for UEFI extra setting [arg2]. | Warning |
| FQXSFPU4089G | UEFI extra setting [arg1] value [arg2] for custom default[arg3] is invalid in current UEFI [arg4]. | Warning |
| FQXSFPU4090G | UEFI extra setting [arg1] is not found after updating UEFI to [arg2]. | Warning |
| FQXSFPU4091G | UEFI extra setting [arg1] value is changed from [arg2] to [arg3] after updating UEFI to [arg4]. | Warning |
| FQXSFPU4093G | UEFI setting [arg1] value [arg2] of custom default[arg3] is invalid in current UEFI [arg4]. | Warning |
| FQXSFPU4095G | UEFI extra settings exposure config file import failed. | Warning |
| FQXSFPW0001L | CMOS has been cleared. | Warning |
| FQXSFSR0001M | [arg1] GPT corruption detected, DiskGUID: [arg2] | Warning |
| FQXSFSR0003G | The number of boot attempts has been exceeded. No bootable device found. | Warning |
| FQXSFTR0001L | An invalid date and time have been detected. | Warning |
| FQXSFIO0005M | An intra-board UPI failure has been detected on the link between processor [arg1] port [arg2] and processor [arg3] port [arg4]. | Error |
| FQXSFIO0006M | An inter-board UPI failure has been detected on the link between processor [arg1] port [arg2] and processor [arg3] port [arg4]. | Error |
| FQXSFIO0013M | New added PCI device(s) at [arg1] triggered [arg2] out of resource. | Error |
| FQXSFIO0024M | An error has been detected by the IEH on processor [arg1]. The type of IEH is [arg2]. The index of the IEH is [arg3]. The value of IehErrorStatus register is [arg4]. Please check error logs for additional downstream device error data. | Error |
| FQXSFIO0025M | An error has been detected by the IIO on processor [arg1]. The index of the IIO stack is [arg2]. The type of IIO Internal Error is [arg3]. Please check error logs for additional downstream device error data. | Error |
| FQXSFIO0035M | An Uncorrectable PCIe Error has Occurred at Segment 0x[arg1] Bus 0x[arg2] Device 0x[arg3] Function 0x[arg4]. The Vendor ID for the device is 0x[arg5] and the Device ID is 0x[arg6]. The physical [arg7] number is [arg8]. | Error |
| FQXSFMA0001M | DIMM [arg1] has been disabled due to an error detected during POST. [arg2] | Error |
| FQXSFMA0002M | An uncorrectable memory error has been detected on DIMM [arg1] at address [arg2]. [arg3] | Error |
| FQXSFMA0004N | No system memory has been detected. | Error |
| FQXSFMA0008M | DIMM [arg1] has failed the POST memory test. [arg2] | Error |
| FQXSFMA0009K | Invalid memory configuration for Mirror Mode. Please correct memory configuration. | Error |
| FQXSFMA0027K | Invalid memory configuration (Unsupported DIMM Population) detected. Please verify memory configuration is valid. | Error |
| FQXSFMA0056M | An uncorrected recoverable memory error has been detected on DIMM [arg1] at address [arg2].[arg3] [arg4] | Error |
| FQXSFMA0066M | Memory address parity error occurred on CPU [arg1] channel [arg2] with DIMM [arg3]. | Error |
| FQXSFMA0077N | SMBus failure encountered when accessing to the SPD of DIMM [arg1]. | Error |
| FQXSFMA0078N | System encountered fatal error [arg1] during memory initialization. | Error |
| FQXSFMA0082M | An uncorrected recoverable memory error has been detected on DIMM [arg1] and post package repair (PPR) recorded. | Error |
| FQXSFMA0083M | An uncorrected recoverable memory error has been detected on DIMM [arg1] and post package repair (PPR) recording failed. | Error |
| FQXSFMA0099M | An uncorrected recoverable memory error has been detected on CMM Bay [arg1] at [arg2]. | Error |
| FQXSFPU0016N | A processor within the system has failed the BIST. | Error |
| FQXSFPU0018N | CATERR(IERR) has asserted on processor [arg1]. | Error |
| FQXSFPU0019N | An uncorrectable error has been detected on processor [arg1]. | Error |
| FQXSFPU0027N | System uncorrectable error has occurred on Processor [arg1] Core [arg2] MC bank [arg3] with MC Status [arg4], MC Address [arg5], and MC Misc [arg6]. | Error |
| FQXSFPU0030N | A firmware fault has been detected in the UEFI image. | Error |
| FQXSFPU0031N | The number of POST attempts has reached the value configured in F1 setup.The system has booted with default UEFI settings. User specified settings have been preserved and will be used on subsequent boots unless modified before rebooting. | Error |
| FQXSFPU0035N | A 3-strike timeout has occurred on processor [arg1]. | Error |
| FQXSFPU4056M | TPM card is changed, need install back the original TPM card which shipped with the system. | Error |
| FQXSFSM0008M | Boot permission timeout detected. | Error |
Give documentation feedback