LCD display panel messages

This section provides descriptions and actions for the messages that might display in the LCD system information display panel on the server.

The LCD system information display panel on the server provides messages about the server progress during POST and the actions plan to follow and correct the problem. Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. For more information about the LCD display panel, see LCD system information display panel.

The following table lists the messages that might display in the LCD display panel on the server.

Table 1. LCD display panel messages.

Three-column table with the LCD display messages and actions to correct the problem

Message	Description	Amount of time before the system timeout if no activity	Action
SYS OFF/BLK PWR	The system is off; no power permissions granted by IMM.	-	Normal. No action is required.
SYSTEM OFF	The system is off.	-	Normal. No action is required.
UEFI: AUTH USER	Authenticating the user.	-	Normal. No action is required.
UEFI: F1 SETUP	Waiting at F1 menu.	-	Normal. No action is required.
UEFI: BOOT DIAGS	The system is booting to pDSA	-	Normal. No action is required.
UEFI: BOOT UEFI	Control has been passed to the operating system bootloader.	-	Normal. No action is required.
OPERATING SYS.	UEFI has passed control to the operating system.	-	Normal. No action is required.
UEFI: CSM INIT	Preparing for legacy boot.	-	Normal. No action is required.
UEFI: CSM DONE	Ready to boot legacy.	-	Normal. No action is required.
IMM: READY	IMM is done loading.	-	Normal. No action is required.
Power Fault XXh	A system power fault has occurred.	Immediately	Identify the FRU associated with the VRD. Check the IMM log.
SYSTEM ON	The system is on. The microprocessor has not attempted to fetch from UEFI ROM.	After 1 minute	Inspect the microprocessor (s).
WAITING ON UEFI	UEFI has not fetched code.	After 1 minute	Restart the server. Flash the UEFI firmware. Clear CMOS.
UEFI: MEASUR.IMG	UEFI is running.	After 2 minutes	Restart the server. Flash the UEFI firmware. Clear CMOS.
UEFI: SIG.CHK.PR	Verifying the signature of the primary bank.	After 2 minutes	Flash the UEFI primary bank.
UEFI: SIG.CHK.BK	Verifying the signature of the backup bank.	After 2 minutes	Flash the UEFI backup bank.
UEFI: UPDATE PRI	UEFI is updating the primary bank.	After 2 minutes	Restart the server. Flash the UEFI firmware. Clear CMOS.
UEFI: UPDATE BKP	UEFI is updating the backup bank.	After 2 minutes	Restart the server. Flash the UEFI firmware. Clear CMOS.
UEFI: END SEC	UEFI is running.	After 2 minutes	Restart the server. Flash the UEFI firmware. Clear CMOS.
UEFI: START PEI	UEFI is running.	After 2 minutes	Restart the server. Flash the UEFI firmware. Clear CMOS.
UEFI: MEM INIT	MRC is running.	After 2 minutes	Inspect the memory in the compute books. Check the IMM log.
UEFI: DXE INIT	DXE is running.	After 2 minutes	Restart the server. Flash the UEFI firmware. Clear CMOS.
UEFI: PECI INIT	The PECI data is ready to be read by IMM.	After 2 minutes	Restart the server. Flash the UEFI firmware. Clear CMOS.
UEFI: USB INIT	The USB bus is being initialized.	After 2 minutes	Inspect the USB subsystem. Restart the server.
UEFI: PCI INIT	PCIe initialization is running.	After 10 minutes	Inspect the PCIe subsystem.
UEFI: VIDEO INIT	Video initialization is running.	After 2 minutes	Restart the server. Flash the UEFI firmware. Clear CMOS.
UEFI: SMBIOS RDY	The SMBIOS tables are ready to be sent to IMM.	After 2 minutes	Restart the server. Flash the UEFI firmware. Clear CMOS.
UEFI: SMI INS	UEFI is running.	After 2 minutes	Restart the server. Flash the UEFI firmware. Clear CMOS.
UEFI: BOOTLEG	Booting legacy.	After 2 minutes	Make sure that the boot operating system is installed correctly.
UEFI: UNMAP DSA	UEFI is running.	After 2 minutes	Restart the server. Flash the UEFI firmware. Clear CMOS.
IMM: UBOOT	IMM is loading UBOOT.	After 15 minutes of no activity or 10 IMM reboot cycles	Disconnect the power from the server. Reset IMM, see Setup utility menu choices. Replace the standard I/O book.
IMM: LOADING	IMM is loading the kernel.	After 15 minutes of no activity or 10 IMM reboot cycles	Disconnect the power from the server. Perform a web or inband flash of the IMM firmware using TFTP burn.
IMM: SECURE BOOT	IMM is loading the kernel.	After 15 minutes of no activity or 10 IMM reboot cycles	Disconnect the power from the server. Reset IMM, see Setup utility menu choices. Replace the standard I/O book.
IMM: KERNEL BOOT	IMM is loading the kernel.	After 15 minutes of no activity or 10 IMM reboot cycles	Disconnect the power from the server. Reset IMM, see Setup utility menu choices. Replace the standard I/O book.
IMM: NETWORK	IMM is loading the kernel.	After 15 minutes of no activity or 10 IMM reboot cycles	Disconnect the power from the server. Perform a web or inband flash of the IMM firmware using TFTP burn.
IMM: BOOTING	IMM is loading the kernel.	After 15 minutes of no activity or 10 IMM reboot cycles	Disconnect the power from the server. Perform a web or inband flash of the IMM firmware using TFTP burn.
IMM: PWR ACTIONS	IMM is loading the kernel.	After 15 minutes of no activity or 10 IMM reboot cycles	Disconnect the power from the server. Perform a web or inband flash of the IMM firmware using TFTP burn.
IMM: THERMAL	IMM is loading the kernel.	After 15 minutes of no activity or 10 IMM reboot cycles	Disconnect the power from the server. Perform a web or inband flash of the IMM firmware using TFTP burn.
IMM: FLASH MNGR	IMM is loading the kernel.	After 15 minutes of no activity or 10 IMM reboot cycles	Disconnect the power from the server. Perform a web or inband flash of the IMM firmware using TFTP burn.
IMM: UEFI SYNC	IMM is loading the kernel.	After 15 minutes of no activity or 10 IMM reboot cycles	Disconnect the power from the server. Perform a web or inband flash of the IMM firmware using TFTP burn.