XCC events organized by severity

FQXSPBR4000I

Management Controller [arg1]: Configuration restored from a file by user [arg2] from [arg3] at IP address [arg4].

FQXSPBR4002I

Management Controller [arg1] Reset was caused by restoring default values.

FQXSPBR4004I

Server timeouts set by user [arg1]: EnableOSWatchdog=[arg2], OSWatchdogTimout=[arg3], EnableLoaderWatchdog=[arg4], LoaderTimeout=[arg5].

FQXSPBR4005I

Management Controller [arg1]: Configuration saved to a file by user [arg2].

FQXSPBR4006I

Management Controller [arg1]: Configuration restoration from a file by user [arg2] completed from [arg3] at IP address [arg4].

FQXSPBR4009I

Management Controller [arg1]: cloning configuration from neighbor server [arg2] by group name [arg3].

FQXSPBR400AI

Management Controller [arg1]: cloning configuration from neighbor server [arg2] by group name [arg3] completed.

FQXSPBR400BI

Management Controller [arg1]: cloning configuration from neighbor server [arg2] by group name [arg3] failed to complete.

FQXSPBR400CI

Management Controller [arg1]: cloning configuration from neighbor server [arg2] by group name [arg3] failed to start.

FQXSPBR400DI

Neighbor group clone configuration was initiated by user [arg1].

FQXSPBR400EI

Neighbor group firmware update was initiated by user [arg1].

FQXSPBR400FI

The neighbor group management is [arg1] by user [arg2] from [arg3] at IP address [arg4].

FQXSPBT0007I

No bootable media available for system [ComputerSystemElementName].

FQXSPCA2002I

Numeric sensor [NumericSensorElementName] going low (lower critical) has deasserted.

FQXSPCA2007I

Numeric sensor [NumericSensorElementName] going high (upper non-critical) has deasserted.

FQXSPCA2009I

Numeric sensor [NumericSensorElementName] going high (upper critical) has deasserted.

FQXSPCA2011I

Numeric sensor [NumericSensorElementName] going high (upper non-recoverable) has deasserted.

FQXSPCA2017I

Sensor [SensorElementName] has transitioned to a less severe state from critical.

FQXSPCA2019I

Sensor [SensorElementName] has deasserted the transition to non-recoverable from a less severe state.

FQXSPCN4000I

Serial Redirection set by user [arg1]: Mode=[arg2], BaudRate=[arg3], StopBits=[arg4], Parity=[arg5], SessionTerminateSequence=[arg6].

FQXSPCN4001I

Remote Control session started by user [arg1] in [arg2] mode.

FQXSPCN4002I

User [arg1] has terminated an active CLI console session.

FQXSPCN4003I

Remote Control session started by user [arg1] in [arg2] mode has been closed.

FQXSPCN4004I

User [arg1] has created an active [arg2] console session.

FQXSPCN4005I

A [arg1] console session is timeout.

FQXSPCN4006I

User [arg1] has terminated an active IPMI console session.

FQXSPDM4000I

Inventory data changed for device [arg1], new device data hash=[arg2], new master data hash=[arg3] .

FQXSPDM4001I

Storage [arg1] has changed.

FQXSPDM4003I

TKLM servers set by user [arg1]: TKLMServer1=[arg2] Port=[arg3], TKLMServer2=[arg4] Port=[arg5], TKLMServer3=[arg6] Port=[arg7], TKLMServer4=[arg8] Port=[arg9].

FQXSPDM4004I

TKLM servers device group set by user [arg1]: TKLMServerDeviceGroup=[arg2] .

FQXSPDM4005I

User [arg1] has generated a new encryption key pair and installed a self-signed certificate for the TKLM client.

FQXSPDM4006I

User [arg1] has generated a new encryption key and certificate signing request for the TKLM client.

FQXSPDM4007I

User [arg1] has imported a signed certificate for the TKLM client from [arg2].

FQXSPDM4008I

User [arg1] has imported a server certificate for the TKLM server.

FQXSPDM4009I

User [arg1] has [arg2] file [arg3] from [arg4].

FQXSPDM4010I

Inventory data collecting and processing complete for [arg1], sequence number is [arg2].

FQXSPDM4011I

EKMS server protocol set by user [arg1]: TKLMServerProtocol=[arg2] .

FQXSPEA2001I

Sensor [SensorElementName] has deasserted the transition from normal to non-critical state.

FQXSPEA2002I

Sensor [SensorElementName] has transitioned to a less severe state from critical.

FQXSPEM0003I

The Log [RecordLogElementName] has been cleared.

FQXSPEM0004I

The Log [RecordLogElementName] is full.

FQXSPEM0005I

The Log [RecordLogElementName] is almost full.

FQXSPEM0009I

The System [ComputerSystemElementName] has generated an auxiliary Log Entry in Log [RecordLogElement].

FQXSPEM4000I

The [arg1] on system [arg2] cleared by user [arg3].

FQXSPEM4001I

The [arg1] on system [arg2] is 75% full.

FQXSPEM4002I

The [arg1] on system [arg2] is 100% full.

FQXSPEM4003I

LED [arg1] state changed to [arg2] by [arg3].

FQXSPEM4004I

SNMP [arg1] enabled by user [arg2] .

FQXSPEM4005I

SNMP [arg1] disabled by user [arg2] .

FQXSPEM4006I

Alert Configuration Global Event Notification set by user [arg1]: RetryLimit=[arg2], RetryInterval=[arg3], EntryInterval=[arg4].

FQXSPEM4007I

Alert Recipient Number [arg1] updated: Name=[arg2], DeliveryMethod=[arg3], Address=[arg4], IncludeLog=[arg5], Enabled=[arg6], EnabledAlerts=[arg7], AllowedFilters=[arg8] by user [arg9] from [arg10] at IP address [arg11].

FQXSPEM4008I

SNMP Traps enabled by user [arg1]: EnabledAlerts=[arg2], AllowedFilters=[arg3] .

FQXSPEM4009I

The UEFI Definitions have been changed.

FQXSPEM4010I

UEFI Reported: [arg1].

FQXSPEM4011I

XCC failed to log previous event [arg1].

FQXSPEM4012I

User [arg1] made system [arg2] Encapsulation lite Mode.

FQXSPEM4013I

Battery error was detected by RAID controller. The battery unit needs replacement.([arg1],[arg2],[arg3],[arg4],[arg5])

FQXSPEM4014I

The RAID controller has problem with the battery. Please contact technical support to resolve this issue.([arg1],[arg2],[arg3],[arg4],[arg5])

FQXSPEM4015I

The RAID controller detected unrecoverable error. The controller needs replacement.([arg1],[arg2],[arg3],[arg4],[arg5])

FQXSPEM4016I

The RAID controller detected one or more problems. Please contact technical support for additional assistance.([arg1],[arg2],[arg3],[arg4],[arg5])

FQXSPEM4017I

The RAID controller detected one or more possible configuration changes within the subsystem. Please check the drive LED status. If necessary, contact technical support for additional assistance.([arg1],[arg2],[arg3],[arg4],[arg5])

FQXSPEM4018I

Enclosure/Chassis issue detected with one or more units. Please check the enclosure/chassis units to repair the problem.([arg1],[arg2],[arg3],[arg4],[arg5])

FQXSPEM4019I

Connectivity issue detected with the enclosure/chassis. Please check your cable configurations to repair the problem.([arg1],[arg2],[arg3],[arg4],[arg5])

FQXSPEM4020I

Fan problem detected with the enclosure/chassis. Please check the enclosure/chassis unit fan for correct operation.([arg1],[arg2],[arg3],[arg4],[arg5])

FQXSPEM4022I

Enclosure/Chassis power supply has problem. Please check the enclosure/chassis unit power supply for correct operation.([arg1],[arg2],[arg3],[arg4],[arg5])

FQXSPEM4023I

One or more virtual drive are in abnormal status that may cause unavailable virtual drive. Please check the event logs and if events are targeted to the same disk then replace the drive. If necessary, contact technical support for additional assistance.([arg1],[arg2],[arg3],[arg4],[arg5])

FQXSPEM4024I

The RAID controller detected one or more possible configuration problem within the subsystem. Please check the event logs and if events are targeted to the same disk then replace the drive. If necessary, contact technical support for additional assistance.([arg1],[arg2],[arg3],[arg4],[arg5])

FQXSPEM4025I

One or more virtual drive have problem. Please contact technical support to resolve this issue.([arg1],[arg2],[arg3],[arg4],[arg5])

FQXSPEM4026I

Drive error was detected by RAID controller. Please contact technical support to resolve this issue.([arg1],[arg2],[arg3],[arg4],[arg5])

FQXSPEM4027I

Drive error was detected by RAID controller. Please check the event logs and if events are targeted to the same disk then replace the drive. If necessary, contact technical support for additional assistance.([arg1],[arg2],[arg3],[arg4],[arg5])

FQXSPEM4028I

The port [arg1] of PCIe device [arg2] at [arg3] has link [arg4].

FQXSPEM4029I

All PCIe slots on [arg1] may not be functional based upon your current CPU population.

FQXSPEM4030I

A scheduled operation on the RAID controller has encountered an issue. Refer to RAID Logs under Server Management, Local Storage, for details.([arg1],[arg2],[arg3],[arg4],[arg5])

FQXSPEM4031I

SSD wear threshold setting is changed from [arg1] to [arg2] by user [arg3] from [arg4] at IP address [arg5].

FQXSPEM4032I

Acoustic Mode [arg1] has been engaged. Fan speed limits are in place.

FQXSPEM4033I

Acoustic Mode [arg1] has been disengaged to allow adequate cooling.

FQXSPEM4036I

Dust filter measurement schedule is configured on server [arg1] by user [arg2] from [arg3] at IP address [arg4].

FQXSPEM4037I

Attempting to perform scheduled dust filter measurement on server [arg1].

FQXSPEM4038I

Dust filter measurement schedule is disabled on server [arg1] by user [arg2] from [arg3] at IP address [arg4].

FQXSPEM4039I

Attempting to perform an immediate dust filter measurement on server [arg1] by user [arg2] from [arg3] at IP address [arg4].

FQXSPEM4041I

The SmartNIC in slot [arg1] encountered boot timeout.

FQXSPEM4042I

The SmartNIC in slot [arg1] went through a crash dump.

FQXSPEM4044I

Dust filter measurement was successfully completed, no action is needed.

FQXSPFC4000I

The bare metal connection process has been started.

FQXSPFC4001I

The bare metal update application reports a status of [arg1].

FQXSPFC4002I

System running in setup.

FQXSPFC4003I

UEFI deployment boot mode is enabled for NextBoot.

FQXSPFC4004I

UEFI deployment boot mode is enabled for NextAc.

FQXSPFC4005I

UEFI deployment boot mode has been disabled.

FQXSPFW0003I

The System [ComputerSystemElementName] encountered firmware progress.

FQXSPIO0010I

A Correctable Bus Error has occurred on bus [SensorElementName].

FQXSPIO2003I

System [ComputerSystemElementName] has recovered from a diagnostic interrupt.

FQXSPIO2004I

Bus [SensorElementName] has recovered from a bus timeout.

FQXSPIO2006I

System [ComputerSystemElementName] has recovered from an NMI.

FQXSPIO2007I

A PCI PERR recovery has occurred on system [ComputerSystemElementName].

FQXSPIO2008I

A PCI SERR on system [ComputerSystemElementName] has deasserted.

FQXSPIO2010I

Bus [SensorElementName] has recovered from a Correctable Bus Error.

FQXSPIO4002I

GPU Board Status was recovered by [arg1] of [arg1].

FQXSPMA0022I

Post Package Repair Success for [PhysicalMemoryElementName] on Subsystem [MemoryElementName].

FQXSPMA2007I

Scrub Failure for [PhysicalMemoryElementName] on Subsystem [MemoryElementName] has recovered.

FQXSPMA2010I

[PhysicalMemoryElementName] on Subsystem [MemoryElementName] is no longer Throttled.

FQXSPMA2012I

An Over-Temperature Condition has been removed on the [PhysicalMemoryElementName] on Subsystem [MemoryElementName].

FQXSPMA2024I

Sensor [SensorElementName] has deasserted.

FQXSPNM4000I

Management Controller [arg1] Network Initialization Complete.

FQXSPNM4001I

Ethernet Data Rate modified from [arg1] to [arg2] by user [arg3].

FQXSPNM4002I

Ethernet Duplex setting modified from [arg1] to [arg2] by user [arg3].

FQXSPNM4003I

Ethernet MTU setting modified from [arg1] to [arg2] by user [arg3].

FQXSPNM4004I

Ethernet locally administered MAC address modified from [arg1] to [arg2] by user [arg3].

FQXSPNM4005I

Ethernet interface [arg1] by user [arg2].

FQXSPNM4006I

Hostname set to [arg1] by user [arg2].

FQXSPNM4007I

IP address of network interface modified from [arg1] to [arg2] by user [arg3].

FQXSPNM4008I

IP subnet mask of network interface modified from [arg1] to [arg2] by user [arg3].

FQXSPNM4009I

IP address of default gateway modified from [arg1] to [arg2] by user [arg3].

FQXSPNM4011I

ENET[[arg1]] DHCP-HSTN=[arg2], DN=[arg3], IP@=[arg4], SN=[arg5], GW@=[arg6], DNS1@=[arg7] .

FQXSPNM4012I

ENET[[arg1]] IP-Cfg:HstName=[arg2], IP@=[arg3] ,NetMsk=[arg4], GW@=[arg5] .

FQXSPNM4013I

LAN: Ethernet[[arg1]] interface is no longer active.

FQXSPNM4014I

LAN: Ethernet[[arg1]] interface is now active.

FQXSPNM4015I

DHCP setting changed to [arg1] by user [arg2].

FQXSPNM4016I

Domain name set to [arg1] by user [arg2].

FQXSPNM4017I

Domain Source changed to [arg1] by user [arg2].

FQXSPNM4018I

DDNS setting changed to [arg1] by user [arg2].

FQXSPNM4019I

DDNS registration successful. The domain name is [arg1].

FQXSPNM4020I

IPv6 enabled by user [arg1] .

FQXSPNM4021I

IPv6 disabled by user [arg1] .

FQXSPNM4022I

IPv6 static IP configuration enabled by user [arg1].

FQXSPNM4023I

IPv6 DHCP enabled by user [arg1].

FQXSPNM4024I

IPv6 stateless auto-configuration enabled by user [arg1].

FQXSPNM4025I

IPv6 static IP configuration disabled by user [arg1].

FQXSPNM4026I

IPv6 DHCP disabled by user [arg1].

FQXSPNM4027I

IPv6 stateless auto-configuration disabled by user [arg1].

FQXSPNM4028I

ENET[[arg1]] IPv6-LinkLocal:HstName=[arg2], IP@=[arg3] ,Pref=[arg4].

FQXSPNM4029I

ENET[[arg1]] IPv6-Static:HstName=[arg2], IP@=[arg3] ,Pref=[arg4], GW@=[arg5] .

FQXSPNM4030I

ENET[[arg1]] DHCPv6-HSTN=[arg2], DN=[arg3], IP@=[arg4], Pref=[arg5], DNS1@=[arg5].

FQXSPNM4031I

IPv6 static address of network interface modified from [arg1] to [arg2] by user [arg3].

FQXSPNM4033I

Telnet port number changed from [arg1] to [arg2] by user [arg3].

FQXSPNM4034I

SSH port number changed from [arg1] to [arg2] by user [arg3].

FQXSPNM4035I

Web-HTTP port number changed from [arg1] to [arg2] by user [arg3].

FQXSPNM4036I

Web-HTTPS port number changed from [arg1] to [arg2] by user [arg3].

FQXSPNM4037I

CIM/XML HTTP port number changed from [arg1] to [arg2] by user [arg3].

FQXSPNM4038I

CIM/XML HTTPS port number changed from [arg1] to [arg2] by user [arg3].

FQXSPNM4039I

SNMP Agent port number changed from [arg1] to [arg2] by user [arg3].

FQXSPNM4040I

SNMP Traps port number changed from [arg1] to [arg2] by user [arg3].

FQXSPNM4041I

Syslog port number changed from [arg1] to [arg2] by user [arg3].

FQXSPNM4042I

Remote Presence port number changed from [arg1] to [arg2] by user [arg3].

FQXSPNM4043I

SMTP Server set by user [arg1] to [arg2]:[arg3].

FQXSPNM4044I

Telnet [arg1] by user [arg2].

FQXSPNM4045I

DNS servers set by user [arg1]: UseAdditionalServers=[arg2], PreferredDNStype=[arg3], IPv4Server1=[arg4], IPv4Server2=[arg5], IPv4Server3=[arg6], IPv6Server1=[arg7], IPv6Server2=[arg8], IPv6Server3=[arg9].

FQXSPNM4046I

LAN over USB [arg1] by user [arg2].

FQXSPNM4047I

LAN over USB Port Forwarding set by user [arg1]: ExternalPort=[arg2], USB-LAN port=[arg3].

FQXSPNM4048I

PXE boot requested by user [arg1].

FQXSPNM4049I

User [arg1] has initiated a TKLM Server Connection Test to check connectivity to server [arg2].

FQXSPNM4050I

User [arg1] has initiated an SMTP Server Connection Test.

FQXSPNM4051I

User [arg1] has set the SMTP Server reverse-path to [arg2].

FQXSPNM4052I

DHCP specified hostname is set to [arg1] by user [arg2].

FQXSPNM4053I

DNS discovery of Lenovo XClarity Administrator has been [arg1] by user [arg2].

FQXSPNM4054I

The hostname from DHCP is [arg1] by user [arg2].

FQXSPNM4055I

The hostname from DHCP is invalid.

FQXSPNM4056I

The NTP server address [arg1] is invalid.

FQXSPNM4057I

Security: IP address: [arg1] had [arg2] login failures, it will be blocked to access for [arg3] minutes.

FQXSPNM4058I

IP address of network interface [arg1] is modified from [arg2] to [arg3] by user [arg4].

FQXSPNM4059I

IP subnet mask of network interface [arg1] is modified from [arg2] to [arg3] by user [arg4].

FQXSPNM4060I

IP address of default gateway of network interface [arg1] is modified from [arg2] to [arg3] by user [arg4].

FQXSPOS4000I

OS Watchdog response [arg1] by [arg2] .

FQXSPOS4001I

Watchdog [arg1] Screen Capture Occurred .

FQXSPOS4004I

Operating System status has changed to [arg1].

FQXSPOS4005I

Host Power-On password changed by user [arg1] from [arg2] at IP address [arg3].

FQXSPOS4006I

Host Power-On password cleared by user [arg1] from [arg2] at IP address [arg3].

FQXSPOS4007I

Host Admin password changed by user [arg1] from [arg2] at IP address [arg3].

FQXSPOS4008I

Host Admin password cleared by user [arg1] from [arg2] at IP address [arg3].

FQXSPOS4009I

OS Crash Video Captured.

FQXSPOS4011I

OS failure screen capture with hardware error is [arg1] by user [arg2] from [arg3] at IP address [arg4].

FQXSPOS4012I

POST watchdog Screen Capture Occurred.

FQXSPPP4000I

Attempting to [arg1] server [arg2] by user [arg3].

FQXSPPP4001I

Server Power Off Delay set to [arg1] by user [arg2].

FQXSPPP4002I

Server [arg1] scheduled for [arg2] at [arg3] by user [arg4].

FQXSPPP4003I

Server [arg1] scheduled for every [arg2] at [arg3] by user [arg4].

FQXSPPP4004I

Server [arg1] [arg2] cleared by user [arg3].

FQXSPPP4005I

The power cap value changed from [arg1] watts to [arg2] watts by user [arg3].

FQXSPPP4006I

The minimum power cap value changed from [arg1] watts to [arg2] watts.

FQXSPPP4007I

The maximum power cap value changed from [arg1] watts to [arg2] watts.

FQXSPPP4008I

The soft minimum power cap value changed from [arg1] watts to [arg2] watts.

FQXSPPP4011I

Power capping was activated by user [arg1].

FQXSPPP4012I

Power capping was deactivated by user [arg1].

FQXSPPP4013I

Static Power Savings mode has been turned on by user [arg1].

FQXSPPP4014I

Static Power Savings mode has been turned off by user [arg1].

FQXSPPP4015I

Dynamic Power Savings mode has been turned on by user [arg1].

FQXSPPP4016I

Dynamic Power Savings mode has been turned off by user [arg1].

FQXSPPP4017I

Power cap and external throttling occurred.

FQXSPPP4018I

External throttling occurred .

FQXSPPP4019I

Power cap throttling occurred.

FQXSPPP4020I

The measured power value has returned below the power cap value.

FQXSPPP4021I

The new minimum power cap value has returned below the power cap value.

FQXSPPP4022I

The server was restarted for an unknown reason.

FQXSPPP4023I

The server is restarted by chassis control command.

FQXSPPP4024I

The server was reset via push button.

FQXSPPP4025I

The server was powered-up via power push button.

FQXSPPP4026I

The server was restarted when the watchdog expired..

FQXSPPP4027I

The server was restarted for OEM reason.

FQXSPPP4028I

The server was automatically powered on because the power restore policy is set to always on.

FQXSPPP4029I

The server was automatically powered on because the power restore policy is set to restore previous power state..

FQXSPPP4030I

The server was reset via Platform Event Filter.

FQXSPPP4031I

The server was power-cycled via Platform Event Filter.

FQXSPPP4032I

The server was soft reset.

FQXSPPP4033I

The server was powered up via Real Time Clock (scheduled power on).

FQXSPPP4034I

The server was powered off for an unknown reason.

FQXSPPP4035I

The server was powered off by chassis control command.

FQXSPPP4036I

The server was powered off via push button.

FQXSPPP4037I

The server was powered off when the watchdog expired.

FQXSPPP4038I

The server stayed powered off because the power restore policy is set to always off.

FQXSPPP4039I

The server stayed powered off because the power restore policy is set to restore previous power state..

FQXSPPP4040I

The server was powered off via Platform Event Filter.

FQXSPPP4041I

The server was powered off via Real Time Clock (scheduled power off).

FQXSPPP4042I

Management Controller [arg1] reset was initiated due to Power-On-Reset.

FQXSPPP4043I

Management Controller [arg1] reset was initiated by PRESET.

FQXSPPP4044I

Management Controller [arg1] reset was initiated by CMM.

FQXSPPP4045I

Management Controller [arg1] reset was initiated by XCC firmware.

FQXSPPP4046I

Remote power permission is [arg1].

FQXSPPP4047I

Management Controller [arg1] reset was initiated by user [arg2].

FQXSPPP4048I

Attempting to AC power cycle server [arg1] by user [arg2].

FQXSPPP4049I

Management Controller [arg1] reset was initiated by Front Panel.

FQXSPPP4050I

Management Controller [arg1] reset was initiated to activate PFR Firmware.

FQXSPPP4051I

The progrmmable GPU total power capping value in slot [arg1] is changed to [arg2] watts by user [arg3] from [arg4] at IP address [arg5].

FQXSPPP4052I

The progrmmable GPU peak power capping value in slot [arg1] is changed to [arg2] watts by user [arg3] from [arg4] at IP address [arg5].

FQXSPPP4053I

This message is reserved.

FQXSPPP4054I

Unbalanced PSU config is detected, system is using less node PSU capacity.

FQXSPPU2001I

An Over-Temperature Condition has been removed on [ProcessorElementName].

FQXSPPU2002I

The Processor [ProcessorElementName] is no longer operating in a Degraded State.

FQXSPPW0001I

[PowerSupplyElementName] has been added to container [PhysicalPackageElementName].

FQXSPPW0005I

[PowerSupplyElementName] is operating in an Input State that is out of range.

FQXSPPW0008I

[SensorElementName] has been turned off.

FQXSPPW0009I

[PowerSupplyElementName] has been Power Cycled.

FQXSPPW2001I

[PowerSupplyElementName] has been removed from container [PhysicalPackageElementName].

FQXSPPW2002I

[PowerSupplyElementName] has returned to OK status.

FQXSPPW2003I

Failure no longer predicted on [PowerSupplyElementName].

FQXSPPW2006I

[PowerSupplyElementName] has returned to a Normal Input State.

FQXSPPW2007I

[PowerSupplyElementName] Configuration is OK.

FQXSPPW2008I

[PowerSupplyElementName] has been turned on.

FQXSPPW2031I

Numeric sensor [NumericSensorElementName] going low (lower non-critical) has deasserted.

FQXSPPW2035I

Numeric sensor [NumericSensorElementName] going low (lower critical) has deasserted.

FQXSPPW2057I

Sensor [SensorElementName] has deasserted the transition from normal to non-critical state.

FQXSPPW2061I

Sensor [SensorElementName] has transitioned to a less severe state from critical.

FQXSPPW2062I

Sensor [SensorElementName] has transitioned to a less severe state from critical.

FQXSPPW2063I

Sensor [SensorElementName] has transitioned to a less severe state from critical.

FQXSPPW4001I

PCIe Power Brake for [arg1] has been [arg2].

FQXSPPW4003I

The customized total graphics power is within the pre-configured limit.

FQXSPSD0000I

The [StorageVolumeElementName] has been added.

FQXSPSD0001I

The [StorageVolumeElementName] Drive [arg1] in the enclosure/chassis(MTM-SN: [arg2]) has been added.

FQXSPSD0003I

Hot Spare enabled for [ComputerSystemElementName].

FQXSPSD0005I

Hot Spare enabled for drive [arg1] in the enclosure/chassis (MTM-SN: [arg2]).

FQXSPSD0007I

Rebuild in progress for Array in system [ComputerSystemElementName].

FQXSPSD0008I

Array rebuild in progress on drive [arg1] in the enclosure/chassis (MTM-S/N: [arg2]).

FQXSPSD2000I

The [StorageVolumeElementName] has been removed from unit [PhysicalPackageElementName].

FQXSPSD2001I

The [StorageVolumeElementName] has recovered from a fault.

FQXSPSD2002I

Failure no longer Predicted on [StorageVolumeElementName] for array [ComputerSystemElementName].

FQXSPSD2003I

Hot spare disabled for [ComputerSystemElementName].

FQXSPSD2005I

Critical Array [ComputerSystemElementName] has deasserted.

FQXSPSD2006I

Array in system [ComputerSystemElementName] has been restored.

FQXSPSD2007I

Rebuild completed for Array in system [ComputerSystemElementName].

FQXSPSD2008I

Drive [arg1] in the enclosure/chassis(MTM-SN: [arg2]) has recovered from a fault.

FQXSPSD2010I

Drive [arg1] in the enclosure/chassis(MTM-SN: [arg2]) has been removed.

FQXSPSD2011I

Failure no longer Predicted on drive [arg1] in the enclosure/chassis (MTM-S/N: [arg2]).

FQXSPSD2012I

Hot Spare disabled for drive [arg1] in the enclosure/chassis (MTM-SN: [arg2]).

FQXSPSD2013I

Array critical deasserted on drive [arg1] in the enclosure/chassis (MTM-S/N: [arg2]).

FQXSPSD2014I

Array restored on drive [arg1] in the enclosure/chassis (MTM-S/N: [arg2]).

FQXSPSD2015I

Array rebuild completed on drive [arg1] in the enclosure/chassis (MTM-S/N: [arg2]).

FQXSPSE4001I

Remote Login Successful. Login ID: [arg1] using [arg2] from [arg3] at IP address [arg4].

FQXSPSE4002I

Security: Userid: [arg1] using [arg2] had [arg3] login failures from WEB client at IP address [arg4].

FQXSPSE4003I

Security: Login ID: [arg1] had [arg2] login failures from CLI at [arg3].

FQXSPSE4004I

Remote access attempt failed. Invalid userid or password received. Userid is [arg1] from WEB browser at IP address [arg2].

FQXSPSE4005I

Remote access attempt failed. Invalid userid or password received. Userid is [arg1] from TELNET client at IP address [arg2].

FQXSPSE4007I

Security: Userid: [arg1] using [arg2] had [arg3] login failures from an SSH client at IP address [arg4].

FQXSPSE4008I

SNMPv1 [arg1] set by user [arg2]: Name=[arg3], AccessType=[arg4], Address=[arg5], .

FQXSPSE4009I

LDAP Server configuration set by user [arg1]: SelectionMethod=[arg2], DomainName=[arg3], Server1=[arg4], Server2=[arg5], Server3=[arg6], Server4=[arg7].

FQXSPSE4010I

LDAP set by user [arg1]: RootDN=[arg2], UIDSearchAttribute=[arg3], BindingMethod=[arg4], EnhancedRBS=[arg5], TargetName=[arg6], GroupFilter=[arg7], GroupAttribute=[arg8], LoginAttribute=[arg9].

FQXSPSE4011I

Secure Web services (HTTPS) [arg1] by user [arg2].

FQXSPSE4012I

Secure CIM/XML(HTTPS) [arg1] by user [arg2].

FQXSPSE4013I

Secure LDAP [arg1] by user [arg2].

FQXSPSE4014I

SSH [arg1] by user [arg2].

FQXSPSE4015I

Global Login General Settings set by user [arg1]: AuthenticationMethod=[arg2], LockoutPeriod=[arg3], SessionTimeout=[arg4].

FQXSPSE4016I

Global Login Account Security set by user [arg1]: PasswordRequired=[arg2], PasswordExpirationPeriod=[arg3], MinimumPasswordReuseCycle=[arg4], MinimumPasswordLength=[arg5], MinimumPasswordChangeInterval=[arg6], MaxmumLoginFailures=[arg7], LockoutAfterMaxFailures=[arg8].

FQXSPSE4017I

User [arg1] created.

FQXSPSE4018I

User [arg1] removed.

FQXSPSE4019I

User [arg1] password modified.

FQXSPSE4020I

User [arg1] role set to [arg2].

FQXSPSE4021I

User [arg1] custom privileges set: [arg2][arg3][arg4][arg5][arg6][arg7][arg8][arg9].

FQXSPSE4022I

User [arg1] for SNMPv3 set: AuthenticationProtocol=[arg2], PrivacyProtocol=[arg3], AccessType=[arg4], HostforTraps=[arg5] by user [arg6] from [arg7] at IP address [arg8].

FQXSPSE4023I

SSH Client key added for user [arg1] by user [arg2] from [arg3] at IP address [arg4].

FQXSPSE4024I

SSH Client key imported for user [arg1] from [arg2] by user [arg3] from [arg4] at IP address [arg5].

FQXSPSE4025I

SSH Client key removed from user [arg1] by user [arg2] from [arg3] at IP address [arg4].

FQXSPSE4026I

Security: Userid: [arg1] had [arg2] login failures from a CIM client at IP address [arg3].

FQXSPSE4027I

Remote access attempt failed. Invalid userid or password received. Userid is [arg1] from a CIM client at IP address [arg2].

FQXSPSE4028I

Security: Userid: [arg1] had [arg2] login failures from IPMI client at IP address [arg3].

FQXSPSE4029I

Security: Userid: [arg1] had [arg2] login failures from SNMP client at IP address [arg3].

FQXSPSE4030I

Security: Userid: [arg1] had [arg2] login failures from IPMI serial client.

FQXSPSE4031I

Remote Login Successful. Login ID: [arg1] from [arg2] serial interface.

FQXSPSE4032I

Login ID: [arg1] from [arg2] at IP address [arg3] has logged off.

FQXSPSE4033I

Login ID: [arg1] from [arg2] at IP address [arg3] has been logged off.

FQXSPSE4034I

User [arg1] has removed a certificate.

FQXSPSE4035I

A certificate has been revoked .

FQXSPSE4036I

The [arg1] certificate is expired and has been removed.

FQXSPSE4037I

Crypto mode modified from [arg1] to [arg2] by user [arg3].

FQXSPSE4038I

Minimum TLS level modified from [arg1] to [arg2] by user [arg3].

FQXSPSE4039I

Temporary user account [arg1] is created by inband tool.

FQXSPSE4040I

Temporary user account [arg1] expires.

FQXSPSE4041I

Security: Userid: [arg1] had [arg2] login failures from a SFTP client at IP address [arg3].

FQXSPSE4042I

The third-party password function [arg1] by user [arg2] from [arg3] at IP address [arg4].

FQXSPSE4043I

Retrieving the third-party password [arg1] by user [arg2] from [arg3] at IP address [arg4].

FQXSPSE4044I

User [arg1] third-party hashed password has been [arg2] by user [arg3] from [arg4] at IP address [arg5].

FQXSPSE4045I

The Salt of user [arg1] third-party password has been [arg2] by user [arg3] from [arg4] at IP address [arg5].

FQXSPSE4046I

The third-party password of the user [arg1] has been retrieved by user [arg2] from [arg3] at IP address [arg4].

FQXSPSE4047I

Role [arg1] is [arg2] and assigned with custom privileges [arg3][arg4][arg5][arg6][arg7][arg8][arg9][arg10][arg11] by user [arg12] .

FQXSPSE4048I

Role [arg1] is removed by user [arg2].

FQXSPSE4049I

Role [arg1] is assigned to user [arg2] by user [arg3].

FQXSPSE4050I

[arg1] sent IPMI command from [arg2], raw data: [arg3][arg4][arg5].

FQXSPSE4051I

Management Controller [arg1] joined the neighbor group [arg2] by user [arg3] at IP address [arg4].

FQXSPSE4052I

The password of neighbor group [arg1] is modified by [arg2] [arg3] at IP address [arg4].

FQXSPSE4053I

Management Controller [arg1] left the neighbor group [arg2] by user [arg3] at IP address [arg4].

FQXSPSE4054I

IPMI SEL wrapping mode is [arg1] by user [arg2] at IP address [arg3].

FQXSPSE4055I

SED encryption is enabled by user [arg1] at IP address [arg2].

FQXSPSE4056I

SED AK is [arg1] by user [arg2] at IP address [arg3].

FQXSPSE4057I

User [arg1] created by user [arg2] from [arg3] at IP address [arg4].

FQXSPSE4058I

User [arg1] removed by user [arg2] from [arg3] at IP address [arg4].

FQXSPSE4059I

User [arg1] password modified by user [arg2] from [arg3] at IP address [arg4].

FQXSPSE4060I

User [arg1] role set to [arg2] by user [arg3] from [arg4] at IP address [arg5].

FQXSPSE4061I

User [arg1] custom privileges set: [arg2][arg3][arg4][arg5][arg6][arg7][arg8][arg9] by user [arg10] from [arg11] at IP address [arg12].

FQXSPSE4062I

The system guard snapshot is captured by user [arg1] from [arg2] at IP address [arg3].

FQXSPSE4063I

The system guard configuration is updated: status=[arg1], hardware inventory=[arg2] and action=[arg3] by user [arg4] from [arg5] at IP address [arg6].

FQXSPSE4064I

SNMPv3 engine ID is changed from [arg1] to [arg2] by user [arg3] from [arg4] at IP address [arg5].

FQXSPSE4065I

SFTP [arg1] by user [arg2] from [arg3] at IP address [arg4].

FQXSPSE4066I

Security mode is modified from [arg1] to [arg2] by user [arg3] from [arg4] at IP address [arg5].

FQXSPSE4067I

User [arg1] accessible interfaces is set to [arg2][arg3][arg4][arg5][arg6] by user [arg7] from [arg8] at IP address [arg9].

FQXSPSE4068I

Security: Userid: [arg1] using [arg2] had [arg3] login failures from Redfish client at IP address [arg4].

FQXSPSE4069I

LDAP set by user [arg1]: RootDN=[arg2], UIDSearchAttribute=[arg3], BindingMethod=[arg4], TargetName=[arg5], GroupFilter=[arg6], GroupAttribute=[arg7], LoginAttribute=[arg8].

FQXSPSE4070I

Lockdown mode is [arg1] by user [arg2] from [arg3] at IP address [arg4].

FQXSPSE4071I

Chassis Intrusion detection is [arg1] by user [arg2] from [arg3] at IP address [arg4].

FQXSPSE4072I

Random SED AK is regenerated by user [arg1] from [arg2] at IP address [arg3].

FQXSPSE4073I

Motion detection is [arg1] by user [arg2] from [arg3] at IP address [arg4].

FQXSPSE4074I

Security mode downgrades because the XCC2 Platinum Upgrade key is expired or deleted.

FQXSPSE4075I

[arg1] by KCS to allow secure boot to be enabled by user [arg2] from [arg3] at IP address [arg4].

FQXSPSE4076I

[arg1] by KCS to allow secure boot to be disabled by user [arg2] from [arg3] at IP address [arg4].

FQXSPSE4077I

Bluetooth button on front panel is [arg1] on server [arg2] by user [arg3] from [arg4] at IP address [arg5].

FQXSPSE4078I

Bluetooth is [arg1] by pressing bluetooth button on front pannel.

FQXSPSE4079I

The Operator role is [arg1] to contain Remote Console Access permission by user [arg2] from [arg3] at IP address [arg4].

FQXSPSE4080I

The user [arg1] attempts to clear CMOS from [arg2] at IP address [arg4].

FQXSPSE4081I

BMC returns the valid local cached key to UEFI for SED drives.

FQXSPSE4082I

Remote key management server is unaccessable.

FQXSPSE4083I

The local cached key has expired and destroyed it.

FQXSPSE4084I

Periodic connection to remote key management server succeeded.

FQXSPSE4085I

Periodic connection to remote key management server failed.

FQXSPSE4088I

The chassis care-taker node ID is changed from [arg1] to [arg2].

FQXSPSE4089I

The chassis node with node ID [arg1] is inserted.

FQXSPSE4090I

The chassis node with node ID [arg1] is removed.

FQXSPSR2001I

Sensor [SensorElementName] has deasserted the transition to non-recoverable from a less severe state.

FQXSPSS4000I

Management Controller Test Alert Generated by [arg1].

FQXSPSS4001I

Server General Settings set by user [arg1]: Name=[arg2], Contact=[arg3], Location=[arg4], Room=[arg5], RackID=[arg6], Rack U-position=[arg7], Address=[arg8].

FQXSPSS4002I

License key for [arg1] added by user [arg2].

FQXSPSS4003I

License key for [arg1] removed by user [arg2].

FQXSPSS4004I

Test Call Home Generated by user [arg1].

FQXSPSS4005I

Manual Call Home by user [arg1]: [arg2].

FQXSPSS4006I

Call Home to [arg1] failed to complete: [arg2].

FQXSPSS4007I

The BMC functionality tier is changed from [arg1] to [arg2].

FQXSPSS4008I

The [arg1] setting has been changed to [arg2] by user [arg3].

FQXSPSS4009I

System enters LXPM maintenance mode.

FQXSPSS4010I

Test Audit Log generated by user [arg1].

FQXSPSS4011I

Fan speed boost setting is changed from [arg1] to [arg2].

FQXSPTR4000I

Management Controller [arg1] clock has been set from NTP server [arg2].

FQXSPTR4001I

Date and Time set by user [arg1]: Date=[arg2], Time-[arg3], DST Auto-adjust=[arg4], Timezone=[arg5].

FQXSPTR4002I

Synchronize time setting by user [arg1]: Mode=Sync with NTP Server, NTPServerHost1=[arg2]:[arg3],NTPServerHost2=[arg4]:[arg5],NTPServerHost3=[arg6]:[arg7],NTPServerHost4=[arg8]:[arg9],NTPUpdateFrequency=[arg10].

FQXSPTR4003I

Synchronize time setting by user [arg1]: Mode=Sync with server clock.

FQXSPUN0017I

Sensor [SensorElementName] has transitioned to normal state.

FQXSPUN0026I

Device [LogicalDeviceElementName] has been added.

FQXSPUN0048I

The RAID controller in PCI slot [arg1] in optimal status.

FQXSPUN2009I

Sensor [SensorElementName] has deasserted.

FQXSPUN2012I

Sensor [SensorElementName] has deasserted.

FQXSPUN2018I

Sensor [SensorElementName] has deasserted the transition from normal to non-critical state.

FQXSPUN2019I

Sensor [SensorElementName] has transitioned to a less severe state from critical.

FQXSPUN2023I

Sensor [SensorElementName] has deasserted the transition to non-recoverable.

FQXSPUN2050I

The RAID controller in PCI slot [arg1] is no longer in critical status.

FQXSPUP0002I

A firmware or software change occurred on system [ComputerSystemElementName].

FQXSPUP4001I

Flash of [arg1] from [arg2] succeeded for user [arg3] .

FQXSPUP4002I

Flash of [arg1] from [arg2] failed for user [arg3].

FQXSPUP4006I

Auto promote primary XCC to backup is [arg1] by user [arg2] from [arg3] at IP address [arg4].

FQXSPUP4007I

Violation access to XCC SPI flash is detected and isolated.

FQXSPUP4008I

Violation access to UEFI SPI flash is detected and isolated.

FQXSPUP4010I

Flash [arg1] of [arg2] from [arg3] succeeded for user [arg4] .

FQXSPUP4011I

Flash [arg1] of [arg2] from [arg3] failed for user [arg4].

FQXSPWD0000I

Watchdog Timer expired for [WatchdogElementName].

FQXSPWD0001I

Reboot of system [ComputerSystemElementName] initiated by watchdog [WatchdogElementName].

FQXSPWD0002I

Powering off system [ComputerSystemElementName] initiated by watchdog [WatchdogElementName].

FQXSPWD0003I

Power cycle of system [ComputerSystemElementName] initiated by watchdog [WatchdogElementName].

FQXSPWD0004I

Watchdog Timer interrupt occurred for [WatchdogElementName].

FQXSPBR4001I

Running the backup Management Controller [arg1] main application.

FQXSPCA0007J

Numeric sensor [NumericSensorElementName] going high (upper non-critical) has asserted.

FQXSPDM4002I

Device [arg1] VPD is not valid.

FQXSPEA0001J

Sensor [SensorElementName] has transitioned from normal to non-critical state.

FQXSPEM4040I

Dust filter measurement is completed. The airflow pathway is obstructed, check and replace the dust filter, or remove any obstructing object.

FQXSPEM4043I

A [arg1] failure has been detected and need [arg2] to recover.

FQXSPIO0014J

Bus [SensorElementName] is operating in a degraded state.

FQXSPIO4001I

GPU Board Status was changed by [arg1] of [arg1].

FQXSPMA0001I

Error Detected and Corrected for [PhysicalMemoryElementName] on Subsystem [MemoryElementName].

FQXSPMA0010J

[PhysicalMemoryElementName] on Subsystem [MemoryElementName] Throttled.

FQXSPMA0011G

Memory Logging Limit Reached for [PhysicalMemoryElementName] on Subsystem [MemoryElementName].

FQXSPMA0024G

Sensor [SensorElementName] has asserted.

FQXSPMA4034G

Health of DIMM [arg1] is in warning state and sub-state is [arg2].

FQXSPNM4010I

DHCP[[arg1]] failure, no IP address assigned.

FQXSPNM4032I

DHCPv6 failure, no IP address assigned.

FQXSPPP4009I

The measured power value exceeded the power cap value.

FQXSPPP4010I

The new minimum power cap value exceeded the power cap value.

FQXSPPU0010G

The Processor [ProcessorElementName] is operating in a Degraded State due to [ProcessorElementName].

FQXSPPU0013G

[ProcessorElementName] has correctable error.

FQXSPPW0003G

Failure predicted on [PowerSupplyElementName].

FQXSPPW0006I

[PowerSupplyElementName] has lost input.

FQXSPPW0031J

Numeric sensor [NumericSensorElementName] going low (lower non-critical) has asserted.

FQXSPPW0057J

Sensor [SensorElementName] has transitioned from normal to non-critical state.

FQXSPPW4002I

Total graphics power value has exceeded the pre-configured limit.

FQXSPSD0002G

Failure Predicted on [StorageVolumeElementName] for array [ComputerSystemElementName].

FQXSPSD0003G

Failure Predicted on drive [arg1] in the enclosure/chassis (MTM-SN: [arg2]).

FQXSPSE4006I

XCC detected an invalid SSL certificate in the Management Controller [arg1] .

FQXSPUN0009G

Sensor [SensorElementName] has asserted.

FQXSPUN0018J

Sensor [SensorElementName] has transitioned from normal to non-critical state.

FQXSPBR4003I

Platform Watchdog Timer expired for [arg1].

FQXSPBR4007I

Management Controller [arg1]: Configuration restoration from a file by user [arg2] failed to complete from [arg3] at IP address [arg4].

FQXSPBR4008I

Management Controller [arg1]: Configuration restoration from a file by user [arg2] failed to start from [arg3] at IP address [arg4].

FQXSPCA0002M

Numeric sensor [NumericSensorElementName] going low (lower critical) has asserted.

FQXSPCA0009M

Numeric sensor [NumericSensorElementName] going high (upper critical) has asserted.

FQXSPCA0011N

Numeric sensor [NumericSensorElementName] going high (upper non-recoverable) has asserted.

FQXSPCA0017M

Sensor [SensorElementName] has transitioned to critical from a less severe state.

FQXSPCA0019N

Sensor [SensorElementName] has transitioned to non-recoverable from a less severe state.

FQXSPEA0002M

Sensor [SensorElementName] has transitioned to critical from a less severe state.

FQXSPFW0000N

The System [ComputerSystemElementName] encountered a POST Error.

FQXSPFW0002N

The System [ComputerSystemElementName] encountered a firmware hang.

FQXSPIO0003N

A diagnostic interrupt has occurred on system [ComputerSystemElementName].

FQXSPIO0004L

A bus timeout has occurred on bus [SensorElementName].

FQXSPIO0006N

A software NMI has occurred on system [ComputerSystemElementName].

FQXSPIO0007N

A PCI PERR has occurred on system [ComputerSystemElementName].

FQXSPIO0008N

A PCI SERR has occurred on system [ComputerSystemElementName].

FQXSPIO0011N

An Uncorrectable Error has occurred on [SensorElementName].

FQXSPIO0013N

A Fatal Bus Error has occurred on bus [SensorElementName].

FQXSPIO0015M

Fault in slot [PhysicalConnectorSystemElementName] on system [ComputerSystemElementName].

FQXSPMA0002N

Configuration Error for [PhysicalMemoryElementName] on Subsystem [MemoryElementName].

FQXSPMA0006N

Parity Error for [PhysicalMemoryElementName] on Subsystem [MemoryElementName].

FQXSPMA0007L

Scrub Failure for [PhysicalMemoryElementName] on Subsystem [MemoryElementName].

FQXSPMA0008N

Uncorrectable error detected for [PhysicalMemoryElementName] on Subsystem [MemoryElementName].

FQXSPMA0012M

An Over-Temperature Condition has been detected on the [PhysicalMemoryElementName] on Subsystem [MemoryElementName].

FQXSPMA4035M

Health of DIMM [arg1] is in error state and sub-state is [arg2].

FQXSPOS4002I

Watchdog [arg1] Failed to Capture Screen.

FQXSPOS4003I

Platform Watchdog Timer expired for [arg1].

FQXSPOS4010I

OS Crash Video Capture Failed.

FQXSPPU0001N

An Over-Temperature Condition has been detected on [ProcessorElementName].

FQXSPPU0003N

[ProcessorElementName] has Failed with IERR.

FQXSPPU0004M

[ProcessorElementName] has Failed with FRB1/BIST condition.

FQXSPPU0009N

[ProcessorElementName] has a Configuration Mismatch.

FQXSPPU0011N

An SM BIOS Uncorrectable CPU complex error for [ProcessorElementName] has asserted.

FQXSPPU0012M

[ProcessorElementName] has machine check error.

FQXSPPW0002L

[PowerSupplyElementName] has Failed.

FQXSPPW0007L

[PowerSupplyElementName] has a Configuration Mismatch.

FQXSPPW0035M

Numeric sensor [NumericSensorElementName] going low (lower critical) has asserted.

FQXSPPW0061M

Sensor [SensorElementName] has transitioned to critical from a less severe state.

FQXSPPW0062M

Sensor [SensorElementName] has transitioned to critical from a less severe state.

FQXSPPW0063M

Sensor [SensorElementName] has transitioned to critical from a less severe state.

FQXSPSD0001L

The [StorageVolumeElementName] has a fault.

FQXSPSD0002L

Drive [arg1] in the enclosure/chassis(MTM-SN: [arg2]) has a fault.

FQXSPSD0005L

Array [ComputerSystemElementName] is in critical condition.

FQXSPSD0006L

Array [ComputerSystemElementName] has failed.

FQXSPSD0007L

Array critical asserted on drive [arg1] in the enclosure/chassis (MTM-S/N: [arg2]).

FQXSPSD0008L

Array failed on drive [arg1] in the enclosure/chassis (MTM-S/N: [arg2]).

FQXSPSE4000I

Certificate Authority [arg1] has detected a [arg2] Certificate Error.

FQXSPSR0001N

Sensor [SensorElementName] has transitioned to non-recoverable from a less severe state.

FQXSPUN0019M

Sensor [SensorElementName] has transitioned to critical from a less severe state.

FQXSPUN0023N

Sensor [SensorElementName] has transitioned to non-recoverable.

FQXSPUP0007L

Invalid or Unsupported firmware or software was detected on system [ComputerSystemElementName].

FQXSPUP4000I

Please ensure that the Management Controller [arg1] is flashed with the correct firmware. The Management Controller is unable to match its firmware to the server.

FQXSPUP4003I

[arg1] firmware mismatch internal to system [arg2]. Please attempt to flash the [arg3] firmware.

FQXSPUP4004I

XCC firmware mismatch between nodes/servers [arg1] and [arg2]. Please attempt to flash the XCC firmware to the same level on all nodes/servers.

FQXSPUP4005I

FPGA firmware mismatch between nodes/servers [arg1] and [arg2]. Please attempt to flash the FPGA firmware to the same level on all nodes/servers.