Parts list
Identify each of the components that is available for your system with the parts list.
For more information about ordering parts:
Go to Lenovo Data Center Support and navigate to the support page for your node or chassis.
Click .
Enter the serial number to view a listing of parts for your system.
It is highly recommended that you check the power summary data for your server using Lenovo Capacity Planner before purchasing any new parts.
Note
Depending on the model, your server components might look slightly different from the illustration.
The parts listed in the following tables are identified as one of the following:
- T1: Tier 1 customer replaceable unit (CRU). Replacement of Tier 1 CRUs is your responsibility. If Lenovo installs a Tier 1 CRU at your request with no service agreement, you will be charged for the installation.
- T2: Tier 2 customer replaceable unit (CRU). You may install a Tier 2 CRU yourself or request Lenovo to install it, at no additional charge, under the type of warranty service that is designated for your server.
- F: Field replaceable unit (FRU). FRUs must be installed only by trained service technicians.
- C: Consumable and Structural parts. Purchase and replacement of consumable and structural parts is your responsibility. If Lenovo acquires or installs a structural component at your request, you will be charged for the service.
Chassis components
Figure 1. Chassis components
| Description | Type |
|---|---|
| 1 Chassis | T2 |
| 2 Node tray rear filler | T1 |
| 3 Chassis midplane | T2 |
| 4 PSU cage | T1 |
| 5 CRPS power supply unit | T2 |
| 6 PSU filler | T1 |
| 7 Chassis rear shipping brackets (left and right) | T1 |
| 8 Node tray front filler | T1 |
| 9 Chassis front EIA brackets (left and right) | T1 |
Node components
Figure 2. Node components
| Description | Type | Description | Type |
|---|---|---|---|
| 1 Top cover | T1 | 20 MicroSD card | T1 |
2
| T1 | 21 Firmware and RoT security module | F |
| 3 Rear I/O module | T1 | 22 2.5-inch drive filler | T1 |
| 4 PCIe riser filler | T1 | 23 15 mm 2.5-inch drive | T1 |
| 5 PCIe filler | T1 | 24 7 mm 2.5-inch drive | T1 |
| 6 PCIe riser | T2 | 25 System board | F |
| 7 PCIe adapter | T1 | 26 2.5-inch drive backplane | T1 |
| 8 GPU air duct | T1 | 27 Front I/O board | T1 |
| 9 Flash power module | T1 | 28 Node tray | F |
| 10 Fan | T1 | 29 Screws | T1 |
| 11 Power distribution board | T2 | 30 Cables | T1 |
| 12 Internal CFF RAID adapter | T1 | 31 Heat sink | F |
| 13 M.2 boot adapter | T1 | 32 Power bus bar | T1 |
| 14 M.2 heat sink | T2 | 33 Cable walls | T1 |
| 15 M.2 drive | T1 | 34 Flash power module holder | T1 |
| 16 M.2 drive retainer | T1 | 35 Processor Neptune® Core Module | F |
| 17 Memory module | T1 | 36 Rubber heat sink | C |
| 18 CMOS battery (CR2032) | C | 37 Rear I/O module (for water loop) | F |
| 19 Processor | F | 38 Hoses | F |
Give documentation feedback