Removing a microprocessor and heat sink

Use this information to remove a microprocessor and heat sink.

The following notes describe information that you must consider when you remove a microprocessor:

• Each microprocessor socket must always contain a socket cover and heat-sink filler or a microprocessor and heat sink. If the compute node has only one microprocessor, it must be installed in microprocessor socket 1.
• The microprocessor installation tool might become worn after several uses. Make sure that the tool can hold the microprocessor securely if you are reusing an existing microprocessor installation tool. Do not return the tool with other parts that you are returning.
• If you are installing a second microprocessor, the option kit comes with a microprocessor installation tool that you must use when you install a microprocessor. The microprocessor installation tool comes with the replacement microprocessor installed on it and a cover over the microprocessor.
• If you are replacing a defective microprocessor, the CRU kit comes with one installation tool with the replacement microprocessor installed on it and a cover over the microprocessor, and one empty installation tool without a cover.
• If you are replacing a defective microprocessor, you must obtain the following for use during the replacement procedure (see Parts listing, Types 7162 and 2588).
  • Alcohol wipes
  • Thermal grease

Attention

• Remove and install only one microprocessor at a time. When removing or installing a microprocessor, protect the other microprocessor socket with a microprocessor heat sink filler.
• Always use the microprocessor installation tool to remove or install a microprocessor. Failure to use the microprocessor installation tool can damage the microprocessor sockets on the system board. Any damage to the microprocessor sockets might require replacing the system board.

Note

Be sure to use the installation tool that comes with your microprocessor. The installation tool has two settings for installing two different sizes of microprocessors. The settings that are marked on the tool are L for smaller low core microprocessors, and H for larger high core microprocessors. The tool automatically adjusts during use to the correct setting for your microprocessor.

To remove a microprocessor and heat sink, complete the following steps.

1. Remove the cover (see Removing the compute node cover).
2. Locate the microprocessor that is to be removed (see System-board connectors).
3. Remove the heat sink.
   Attention

   Do not touch the thermal material on the bottom of the heat sink. Touching the thermal material will contaminate it.
   1. Use a screwdriver to loosen the screw on one side of the heat sink to break the seal with the microprocessor.
   2. Use a screwdriver to loosen the screws on the heat sink, rotating each screw two full turns until each screw is loose.
   3. Gently pull the heat sink from the microprocessor.
   Attention

   Do not use any tools or sharp objects to lift the release levers on the microprocessor socket. Doing so might result in permanent damage to the system board.
4. Open the microprocessor socket release levers and retainer.
   
   
   
   1. Identify which release lever is labeled as the first release lever to open, and open it.
   2. Open the second release lever on the microprocessor socket.
   3. Open the microprocessor retainer.
   Attention

   Do not touch the connectors on the microprocessor and the microprocessor socket.
5. Remove the microprocessor from the socket.
   1. Select the empty installation tool and ensure that the handle is in the open position. If the installation tool handle is not in the open position, 1) lift the interlock latch and hold it up while you 2) twist the microprocessor installation tool handle counterclockwise to the open position, and then release the interlock latch. The following illustration of the installation tool shows the location of the interlock latch and counterclockwise rotation of the handle before loading the microprocessor.
      
      
      
   2. Align the installation tool with the screws, as shown in the following graphic, and lower the installation tool on the microprocessor. The installation tool rests flush on the socket only when it is aligned correctly.
      
      
      
   3. Remove the microprocessor using the installation tool. Gently twist the handle of the installation tool clockwise until it locks in the H or L position, depending on the size of microprocessor, and then lift the microprocessor out of the socket.