Skip to main content

Replacing an adapter

Use this information to replace an adapter.

The following notes describe the types of adapters that the server supports and other information that you must consider when you install an adapter:
  • To confirm that the server supports the adapter that you are installing, see the Lenovo ServerProven website.
  • Locate the documentation that comes with the adapter and follow those instructions in addition to the instructions in this section.
  • The adapter slots are on the PCI riser-card assembly. You must first remove the PCI riser-card assembly to access the adapter slots.
  • The expansion slots on the PCI riser-card assembly accommodate the various form factors of the non-hot-plug adapters as follows:
    • Expansion slot 1: Low-profile with 2U bracket (this slot is dedicated for ServeRAID-10il v2 SAS/SATA controller)
    • Expansion slot 2: Full-height, half-length
      Figure 1. PCI riser-card assembly
      PCI riser-card assembly
  • The optional ServeRAID-BR10il v2 controller must be installed in expansion slot 1 on the PCI riser-card assembly.

Read the safety information in Safety and Installation guidelines.

If you are replacing a server component in the server, you need to turn off the server and peripheral devices, and disconnect the power cords and all external cables.

The following notes describe the types of adapters that the server supports and other information that you must consider when you install an adapter:
  • Locate the documentation that comes with the adapter and follow those instructions in addition to the instructions in this section. If you have to change switch settings or jumper settings on the adapter, follow the instructions that come with the adapter.
  • The adapter slots are on the PCI riser-card assembly. You must first remove the PCI riser-card assembly to access the adapter slots.
  • The expansion slots on the PCI riser-card assembly accommodate the various form factors of the non-hot-plug adapters as follows:
    • Expansion slot 1: Low-profile with 2U bracket (this slot is dedicated for ServeRAID-10il v2 SAS/SATA controller)
    • Expansion slot 2: Full-height, half-length


  • The optional ServeRAID-BR10il v2 controller must be installed in expansion slot 1 on the PCI riser-card assembly.
Attention
Some cluster solutions require specific code levels or coordinated code updates. If the device is part of a cluster solution, verify that the latest level of code is supported for the cluster solution before you update the code.
To replace an adapter, complete the following steps.
Note
  • If your adapter was previously configured, backup or record its configuration information, if possible, before replacing the adapter. See the documentation for your adapter for information and instructions.

  • If you are replacing a ServeRAID adapter, import your RAID configuration to the replacement adapter as a foreign configuration after you finish the replacement. See the ServeRAID-M Software User Guide for instructions.

  1. Remove the cover (see Removing the cover).
  2. Remove the PCI riser-card assembly (see Removing the PCI riser-card assembly).
  3. Touch the static-protective package that contains the adapter to any unpainted metal surface on the server; then, remove the adapter from the package.
  4. Place the adapter, component side up, on a flat, static-protective surface and set any jumpers or switches as described by the adapter manufacturer, if necessary.
  5. Follow the cabling instructions, if any come with the adapter. Route the adapter cables before you install the adapter.
  6. Remove the expansion-slot cover from the PCI riser-card assembly and save for future use.
  7. Align the connector on the adapter with the connector on the PCI riser-card assembly, then, insert the adapter into the PCI riser-card assembly. Press the edge of the connector firmly into the PCI riser-card assembly. Make sure that the adapter is securely installed in the PCI riser-card assembly.
    Important
    Make sure that the U-shaped opening in the metal adapter bracket engages the tab on the expansion-slot bracket.
    Figure 2. Adapter installation
    Adapter installation
  8. Install the PCI riser-card assembly (see Replacing the PCI riser-card assembly).
    Attention
    When you install an adapter, make sure that the adapter is correctly seated in the PCI riser-card assembly and that the PCI riser-card assembly is securely seated in the riser-card connector on the system board before you turn on the server. An incorrectly seated adapter might cause damage to the system board, the PCI riser-card assembly, or the adapter.
  9. Reinstall the cover (see Replacing the cover).

If you have replaced a server component or installed an optional device in the server, you need to reconnect the power cords and all external cables, and turn on the server and peripheral devices.

Note
To support Windows 2011 SBS on Brocade adapters need to use at least 3.0.0.0 driver package or later version.