Parts list
Use the parts list to identify each of the components that are available for your server.
For more information about ordering parts:
Go to Lenovo Data Center Support and navigate to the support page for the specific server.
Click .
Enter the serial number to view a listing of parts for the specific server.
It is highly recommended that you check the power summary data for your server using Lenovo Capacity Planner before purchasing any new parts.
Note
Depending on the model, your server might look slightly different from the illustration.
The parts listed in the following table are identified as one of the following:
- T1: Tier 1 customer replaceable unit (CRU). Replacement of Tier 1 CRUs is your responsibility. If Lenovo installs a Tier 1 CRU at your request with no service agreement, you will be charged for the installation.
- T2: Tier 2 customer replaceable unit (CRU). You may install a Tier 2 CRU yourself or request Lenovo to install it, at no additional charge, under the type of warranty service that is designated for your server.
- F: Field replaceable unit (FRU). FRUs must be installed only by trained service technicians.
- C: Consumable and Structural parts. Purchase and replacement of consumable and structural parts is your responsibility. If Lenovo acquires or installs a structural component at your request, you will be charged for the service.
Enclosure components
Figure 1. Enclosure components
| Description | Type | Description | Type |
|---|---|---|---|
| 1 Power adapter support bracket | T1 | 4 Enclosure bracket dust filter set | T1 |
| 2 ThinkEdge SE350 V2 Enclosure | F | 5 Node filler | T1 |
| 3 Enclosure front shipping bracket | T1 |
Node components
Figure 2. Server components
| Description | Type | Description | Type |
|---|---|---|---|
| 1 ThinkEdge 300W 230V/115V external power adapter | T1 | 20 MicroSD card | T1 |
| 2 Cable wall | T1 | 21 25GbE/10GbE front I/O bezel | T1 |
| 3 12-48V DC power module board | F | 22 1GbE front I/O bezel | T1 |
| 4 Top cover | T1 | 23 I/O fillers | C |
| 5 Memory module | T2 | 24 CMOS battery (CR2032) | C |
| 6 Fan | T1 | 25 Node chassis | F |
| 7 System board with processor | F | 26 Front operator panel assembly | F |
| 8 Anti-tampering keylock switch bracket | T1 | 27 7mm 2.5-inch drive filler | C |
| 9 Anti-tampering keylock switch with cable | T2 | 28 7mm 2.5-inch hot-swap drive | T1 |
| 10 DC power input board module | F | 29 15mm 2.5-inch drive filler | C |
| 11 Processor heat sink | F | 30 15mm 2.5-inch hot-swap drive | T1 |
| 12 Air baffle | T1 | 31 7mm drive cage | T1 |
| 13 Bridge board | F | 32 Kensington lock (exterior) | T1 |
| 14 15mm/7mm Drive Backplane 1 (lower) | F | 33 Cables | T1 |
| 15 7mm Drive Backplane 2 (upper) | F | 34 15mm drive cage | T1 |
| 16 1GbE I/O module board | F | 35 AC power input board module | F |
| 17 10/25GbE I/O module board | F | 36 Internal power supply unit (AC power module board) | F |
| 18 M.2 heat sink | F | 37 Intrusion switch holder | T2 |
| 19 M.2 boot drive | T1 | 38 Intrusion switch with cable | T2 |
Give documentation feedback