Skip to main content

Remove a processor and heat sink

This task has instructions for removing an assembled processor and heat sink, known as a processor-heat-sink module (PHM), a processor, and a heat sink. All of these tasks require a Torx T30 driver.

Read the installation GuidelinesPower off the server for this taskATTENTION: Static Sensitive Device Ground package before opening
Attention

  • Intel® Xeon® SP Gen 2 processors are supported on the system board with part number 01PE845. If you use the system board with part number 00MX680, update your system firmware to the latest level before installing an Intel® Xeon® SP Gen 2 processor. Otherwise, the system cannot be powered on.

  • Each processor socket must always contain a cover or a PHM. When removing or installing a PHM, protect empty processor sockets with a cover.

  • Do not touch the processor socket or processor contacts. Processor-socket contacts are very fragile and easily damaged. Contaminants on the processor contacts, such as oil from your skin, can cause connection failures.

  • Remove and install only one PHM at a time. If the system board supports multiple processors, install the PHMs starting with the first processor socket.

  • Do not allow the thermal grease on the processor or heat sink to come in contact with anything. Contact with any surface can compromise the thermal grease, rendering it ineffective. Thermal grease can damage components, such as electrical connectors in the processor socket. Do not remove the grease cover from a heat sink until you are instructed to do so.

  • To ensure the best performance, check the manufacturing date on the new heat sink and make sure it does not exceed 2 years. Otherwise, wipe off the existing thermal grease and apply the new grease onto it for optimal thermal performance.

Before removing a PHM:
Note
The heat sink, processor, and processor retainer for your system might be different than those shown in the illustrations.

  1. Remove the top cover. See Remove the top cover.

  2. Remove the air baffle. See Remove the air baffle.

  3. Remove any parts and disconnect any cables that might impede your access to the PHM.

To remove a PHM, complete the following steps:

Watch the procedure

A video of this procedure is available at YouTube.

Remove the PHM from the system board.
Figure 1. Removing a PHM
PHM removal

Attention
To prevent damage to components, make sure that you follow the indicated loosening sequence.
  1. Fully loosen the Torx T30 captive fasteners on the processor-heat-sink module in the removal sequence shown on the heat-sink label.
  2. Lift the processor-heat-sink module from the processor socket.

After removing a PHM:

  • If you are removing the PHM as part of a system board replacement, set the PHM aside.

  • If you are removing the PHM, remove the fan 4 after you remove the PHM. Then, install a fan filler to cover the place.

  • If you are replacing the processor or heat sink, separate the processor and its retainer from the heat sink.

    Figure 2. Separating a heat sink from a processor
    Remove processor from heat sink

    1. Press the retaining clip at the corner of the processor retainer closest to the pry point; then, gently pry this corner of the retainer away from the heat sink with a flat-bladed screwdriver, using a twisting motion to break the processor-to-heat-sink seal.

    2. Release the remaining retaining clips and lift the processor and retainer from the heat sink.

    3. After separating the processor and retainer from the heat sink, hold the processor and retainer with the thermal-grease side down and the processor-contact side up to prevent the processor from falling out of the retainer.

      Note
      The processor retainer will be removed and discarded in a later step and replaced with a new one.

  • If you are replacing the processor, you will be reusing the heat sink. Wipe the thermal grease from the bottom of the heat sink using an alcohol cleaning pad.

  • If you are replacing the heat sink, you will be reusing the processor. Wipe the thermal grease from the top of the processor using an alcohol cleaning pad.

If you are instructed to return the old processor or heat sink, follow all packaging instructions and use any packaging materials that are provided.