Skip to main content

2.5-inch drive bay chassis

Use the parts list in this section to identify each of the components that are available for server models with 2.5-inch front drive bays.

For more information about ordering the parts shown in Figure 1:

Parts list

It is highly recommended that you check the power summary data for your server using Lenovo Capacity Planner before purchasing any new parts.

Note
Depending on the model, your server might look slightly different from the illustration. Some parts are available only on some models.
Figure 1. Server components (2.5-inch drive bay chassis)
Server components (2.5-inch drive bay chassis)
The parts listed in the following table are identified as one of the following:

  • T1: Tier 1 customer replaceable unit (CRU). Replacement of Tier 1 CRUs is your responsibility. If Lenovo installs a Tier 1 CRU at your request with no service agreement, you will be charged for the installation.

  • T2: Tier 2 customer replaceable unit (CRU). You may install a Tier 2 CRU yourself or request Lenovo to install it, at no additional charge, under the type of warranty service that is designated for your server.

  • F: Field replaceable unit (FRU). FRUs must be installed only by trained service technicians.

  • C: Consumable and Structural parts. Purchase and replacement of consumable and structural parts (components, such as a filler or bezel) is your responsibility. If Lenovo acquires or installs a structural component at your request, you will be charged for the service.

DescriptionTypeDescriptionType
1 Top coverT12 Rear 4 x 2.5-inch drive cageT1
3 Rear 8 x 2.5-inch drive cageT14 Riser cages:

  • Riser 1 or riser 2 cage (3FH)

  • Riser 3 cage (2FH)

  • 1U riser cage (LP)

T1
5 Riser cards:

  • Riser 1

  • Riser 2

  • Riser 3

  • T1

  • T1

  • T2

6 PCIe adapterT1
7 Power supplyT18 Serial port moduleT1
9 ProcessorF10 Memory moduleT1
11 Heat sinks

  • 2U entry heat sink

  • 2U standard heat sink

  • High performance T-shape heat sink

  • 1U heat sink

F12 Heat sink PEEK nutT2
13 Rear wall bracketsC14 7mm driveT1
15 7mm drive bay fillerC16 7mm drive cage (2FH + 7mm)T1
17 7mm drive cage (1U)T118 7mm drive backplanesT2
19 OCP 3.0 Ethernet adapterT120 OCP Enablement Kit for vSphere DSET1
21 CFF RAID adapter/expanderT222 M.2 drive backplaneT1
23 M.2 driveT124 M.2 retainer clipT1
25 CMOS battery (CR2032)C26 RAID flash power module holderC
27 RAID flash power moduleT128 TPM adapter (for Chinese Mainland only)F
29 Left rack latch with VGA and external diagnostic connectorT130 Right rack latch with front I/O assemblyT1
31 Standard right rack latchC32 Standard left rack latch with external diagnostic connectorT1
33 External diagnostic handsetT134 Intrusion switchT1
35 Security bezelT136 Integrated diagnostics panelT1
37 Front I/O assembly with integrated diagnostics panelT138 4 x 2.5-inch drive fillerC
39 8 x 2.5-inch drive fillerC40 2.5-inch driveT1
41 2.5-inch drive fillerC42 ChassisF
43 Rear 8 x 2.5-inch drive backplaneT144 Middle/Rear 4 x 2.5-inch drive backplaneT1
45 Front 8 x 2.5-inch drive backplaneT146 Fan cageT1
47 Fan module

  • Standard fan

  • Performance fan

T148 System boardF
49 Middle 8 x 2.5-inch drive cageT150 Air baffle filler (for standard air baffle)C
51 Add-on air baffle (for GPU air baffle)T152 Air baffle filler (for GPU air baffle)C
53 Standard air baffleT154 GPU air baffleT1