Skip to main content

UEFI events organized by severity

The following table lists all UEFI events, organized by severity (Information, Error, and Warning).

Table 1. Events organized by severity
Event IDMessage StringSeverity
FQXSFDD0012ISATA Hard Drive Error: [arg1] was recovered.Informational
FQXSFIO0005IAn intra-board UPI has been disabled on the link between processor [arg1] port [arg2] and processor [arg3]port [arg4] because of UPI topology downgrade.Informational
FQXSFIO0006IAn inter-board UPI has been disabled on the link between processor [arg1] port [arg2] and processor [arg3]port [arg4] because of UPI topology downgrade.Informational
FQXSFIO0015IIFM: System reset performed to reset adapters.Informational
FQXSFIO0018IIFM: Configuration too large for compatibility mode.Informational
FQXSFIO0020JPCIe Isolation has occurred in PCIe slot [arg1]. The adapter may not operate correctly.Informational
FQXSFIO0021IPCIe DPC software triggering occurred in physical [arg1] number [arg2].Informational
FQXSFMA0001IDIMM [arg1] Disable has been recovered. [arg2]Informational
FQXSFMA0002IThe uncorrectable memory error state has been cleared.Informational
FQXSFMA0006I[arg1] DIMM [arg2] has been detected, the DIMM serial number is [arg3].Informational
FQXSFMA0007I[arg1] DIMM number [arg2] has been replaced. [arg3]Informational
FQXSFMA0008IDIMM [arg1] POST memory test failure has been recovered. [arg2]Informational
FQXSFMA0009IInvalid memory configuration for Mirror Mode has been recovered. [arg1]Informational
FQXSFMA0010IInvalid memory configuration for Sparing Mode has been recovered. [arg1]Informational
FQXSFMA0011IMemory population change detected. [arg1]Informational
FQXSFMA0012IThe PFA of DIMM [arg1] has been deasserted.Informational
FQXSFMA0014IMemory spare copy initiated. [arg1]Informational
FQXSFMA0015IMemory spare copy has completed successfully. [arg1]Informational
FQXSFMA0026IDIMM [arg1] Self-healing, attempt post package repair (PPR) succeeded at Rank [arg2] Sub Rank [arg3] Bank [arg4] Row [arg5] on Device [arg6]. [arg7]Informational
FQXSFMA0027IInvalid memory configuration (unsupported DIMM Population) recovered.Informational
FQXSFMA0029IThe PFA of DIMM [arg1] has been deasserted after applying PPR for this DIMM. [arg2]Informational
FQXSFMA0052IDIMM [arg1] has been disabled due to the error on DIMM [arg2].[arg3]Informational
FQXSFMA0053IDIMM [arg1] re-enabled due to memory module combination updating.Informational
FQXSFMA0063IA correctable memory error handled by ADDDC on DIMM [arg1]. DIMM identifier is [arg2].Informational
FQXSFMA0065IMulti-bit CE of DIMM [arg1] has been deasserted after performing post package repair. DIMM identifier is [arg2].Informational
FQXSFPU0020IThe UEFI firmware image capsule signature is invalid.Informational
FQXSFPU0021IThe TPM physical presence state has been cleared.Informational
FQXSFPU0023ISecure Boot Image Verification Failure has been cleared as no failure in this round boot.Informational
FQXSFPU0025IThe default system settings have been restored.Informational
FQXSFPU4034ITPM Firmware recovery is finished, rebooting system to take effect.Informational
FQXSFPU4038ITPM Firmware recovery successful.Informational
FQXSFPU4041ITPM Firmware update is in progress. Please DO NOT power off or reset system.Informational
FQXSFPU4042ITPM Firmware update is finished, rebooting system to take effect.Informational
FQXSFPU4044IThe current TPM firmware version could not support TPM version toggling.Informational
FQXSFPU4046ITPM Firmware will be updated from TPM1.2 to TPM2.0.Informational
FQXSFPU4047ITPM Firmware will be updated from TPM2.0 to TPM1.2.Informational
FQXSFPU4049ITPM Firmware update successful.Informational
FQXSFPU4059IUser requested to skip freezing lock of AHCI-attached SATA drives. System UEFI accepted the request and will execute priot to OS boot.Informational
FQXSFPU4060ISkipped freezing lock of AHCI-attached SATA drives.Informational
FQXSFPU4061IRestored default locking behavior of AHCI-attached SATA drives.Informational
FQXSFPU4062ICPU debugging is deactivated for DCI interface.Informational
FQXSFPU4080IHost Power-On password has been changed.Informational
FQXSFPU4081IHost Power-On password has been cleared.Informational
FQXSFPU4082IHost Admin password has been changed.Informational
FQXSFPU4083IHost Admin password has been cleared.Informational
FQXSFPU4084IHost boot order has been changed.Informational
FQXSFPU4085IHost WOL boot order has been changed.Informational
FQXSFSM0007IThe XCC System Event log (SEL) is full.Informational
FQXSFSR0002I[arg1] GPT corruption recovered, DiskGUID: [arg2]Informational
FQXSFDD0001GDRIVER HEALTH PROTOCOL: Missing Configuration. Requires Change Settings From F1.Warning
FQXSFDD0002MDRIVER HEALTH PROTOCOL: Reports 'Failed' Status Controller.Warning
FQXSFDD0003IDRIVER HEALTH PROTOCOL: Reports 'Reboot' Required Controller.Warning
FQXSFDD0005MDRIVER HEALTH PROTOCOL: Disconnect Controller Failed. Requires 'Reboot'.Warning
FQXSFDD0006MDRIVER HEALTH PROTOCOL: Reports Invalid Health Status Driver.Warning
FQXSFDD0007GSecurity Key Lifecycle Manager (SKLM) IPMI Error.Warning
FQXSFIO0008MAn intra-board UPI dynamic link width reduction has been detected on the link between processor [arg1] port [arg2] and processor [arg3] port [arg4].Warning
FQXSFIO0009MAn inter-board UPI dynamic link width reduction has been detected on the link between processor [arg1] port [arg2] and processor [arg3] port [arg4].Warning
FQXSFIO0013IThe device found at Bus [arg1] Device [arg2] Function [arg3] could not be configured due to resource constraints. The Vendor ID for the device is [arg4] and the Device ID is [arg5]. The physical slot number is [arg6].Warning
FQXSFIO0016MIFM: Reset loop avoided - Multiple resets not allowed.Warning
FQXSFIO0021JPCIe Error Recovery has occurred in physical [arg1] number [arg2]. The [arg3] may not operate correctly.Warning
FQXSFIO0022JPCIe Link Width has degraded from [arg1] to [arg2] in physical [arg3] number [arg4].Warning
FQXSFIO0023JPCIe Link Speed has degraded from [arg1] to [arg2] in physical [arg3] number [arg4].Warning
FQXSFIO0024IAn error has been detected by the IEH on processor [arg1]. The type of IEH is [arg2]. The index of the IEH is [arg3]. The value of IehErrorStatus register is [arg4]. Please check error logs for additional downstream device error data.Warning
FQXSFIO0025IAn error has been detected by the IIO on processor [arg1]. The index of the IIO stack is [arg2]. The type of IIO Internal Error is [arg3]. Please check error logs for additional downstream device error data.Warning
FQXSFIO0036GPCIe Correctable Error Threshold limit has been exceeded at Segment 0x[arg1] Bus 0x[arg2] Device 0x[arg3] Function 0x[arg4]. The Vendor ID for the device is 0x[arg5] and the Device ID is 0x[arg6]. The physical [arg7] number is [arg8].Warning
FQXSFIO0041JPCIe Leaky Bucket Event : [arg1] occurred at Segment [arg2] Bus [arg3] Device [arg4] Function [arg5]. The physical [arg6] number is [arg7].Warning
FQXSFMA0016MMemory spare copy failed. [arg1]Warning
FQXSFMA0026GMulti-bit CE occurred on DIMM [arg1], need to restart the system for DIMM Self-healing to attempt post package repair (PPR)Warning
FQXSFMA0027GMulti-bit CE occurred on DIMM [arg1] different rows.[arg2]Warning
FQXSFMA0027MDIMM [arg1] Self-healing, attempt post package repair (PPR) failed at Rank [arg2] Sub Rank [arg3] Bank [arg4] Row [arg5] on Device [arg6]. [arg7]Warning
FQXSFMA0028MDIMM [arg1] Self-healing, attempt post package repair (PPR) exceeded DIMM level threshold [arg2] at Rank [arg3] Sub Rank [arg4] Bank [arg5] Row [arg6] on Device [arg7]. [arg8]Warning
FQXSFMA0047MSPD CRC checking failed on DIMM [arg1]. [arg2]Warning
FQXSFMA0048MDIMM [arg1] disabled due to PMIC failure during POST, DIMM identifier is [arg2].Warning
FQXSFMA0049MDIMM [arg1] disabled due to memory module power failure. DIMM [arg2] detected and good, DIMM [arg3] not detected.Warning
FQXSFMA0050GDRAM PFA threshold limit exceeded on DIMM [arg1] sub-channel [arg2] Rank [arg3] DRAM [arg4], DIMM identifier is [arg5].Warning
FQXSFMA0053GAn uncorrected memory error has been recovered by mirror on DIMM [arg1] at address [arg2].[arg3]Warning
FQXSFMA0053MDIMM [arg1] not defective but disabled due to unsupported memory module combination on CPU [arg2].Warning
FQXSFMA0054GMirror failover operation was successful. DIMM [arg1] has failed over to the mirrored DIMM [arg2].[arg3]Warning
FQXSFMA0055GMirror failover operation was unsuccessful. DIMM [arg1] cannot fail over again.[arg2]Warning
FQXSFMA0057GPage Retire PFA Threshold limit exceeded on DIMM [arg1] at address [arg2].[arg3] [arg4]Warning
FQXSFMA0064MDIMM [arg1] disabled due to memory module power failure. DIMM [arg2] detected and good.Warning
FQXSFMA0067GErrors per row counter threshold limit exceeded on DIMM [arg1] sub-channel [arg2] Rank [arg3] DRAM [arg4], need to restart the system for DIMM Self-healing to attempt post package repair (PPR), DIMM identifier is [arg5].Warning
FQXSFPU0022GThe TPM configuration is not locked.Warning
FQXSFPU0023GSecure Boot Image Verification Failure Warning.Warning
FQXSFPU0033GProcessor has been disabled.Warning
FQXSFPU0062FSystem uncorrected recoverable error happened in Processor [arg1] Core [arg2] MC bank [arg3] with MC Status [arg4], MC Address [arg5], and MC Misc [arg6].Warning
FQXSFPU4033FTPM Firmware recovery is in progress. Please DO NOT power off or reset system.Warning
FQXSFPU4035MTPM Firmware recovery failed. TPM chip may be damaged.Warning
FQXSFPU4040MTPM selftest has failed.Warning
FQXSFPU4043GTPM Firmware update aborted. System is rebooting...Warning
FQXSFPU4050GFailed to update TPM Firmware.Warning
FQXSFPU4051GUndefined TPM_POLICY foundWarning
FQXSFPU4052GTPM_POLICY is not lockedWarning
FQXSFPU4053GSystem TPM_POLICY does not match the planar.Warning
FQXSFPU4054GTPM card logical binding has failed.Warning
FQXSFPU4062MCPU debugging is activated for DCI interface.Warning
FQXSFPW0001LCMOS has been cleared.Warning
FQXSFSM0002NBoot Permission denied by Management Module: System Halted.Warning
FQXSFSM0003NTimed Out waiting on boot permission from Management Module: System Halted.Warning
FQXSFSM0004MAn XCC communication failure has occurred.Warning
FQXSFSR0001M[arg1] GPT corruption detected, DiskGUID: [arg2]Warning
FQXSFSR0003GThe number of boot attempts has been exceeded. No bootable device found.Warning
FQXSFTR0001LAn invalid date and time have been detected.Warning
FQXSFDD0004MDRIVER HEALTH PROTOCOL: Reports 'System Shutdown' Required Controller.Error
FQXSFDD0012KSATA Hard Drive Error: [arg1].Error
FQXSFIO0005MAn intra-board UPI failure has been detected on the link between processor [arg1] port [arg2] and processor [arg3] port [arg4].Error
FQXSFIO0006MAn inter-board UPI failure has been detected on the link between processor [arg1] port [arg2] and processor [arg3] port [arg4].Error
FQXSFIO0007MAn error has been detected by the IIO on Bus [arg1]. The value of Global Fatal Error Status register is [arg2]. The value of Global Non-Fatal Error Status register is [arg3]. Please check error logs for additional downstream device error data.Error
FQXSFIO0010MAn Uncorrectable PCIe Error has Occurred at Bus [arg1] Device [arg2] Function [arg3]. The Vendor ID for the device is [arg4] and the Device ID is [arg5]. The physical [arg6] number is [arg7].Error
FQXSFIO0011MA PCIe parity error has occurred on Bus [arg1] Device [arg2] Function [arg3]. The Vendor ID for the device is [arg4] and the Device ID is [arg5]. The Physical slot number is [arg6].Error
FQXSFIO0012MA PCIe system error has occurred on Bus [arg1] Device [arg2] Function [arg3]. The Vendor ID for the device is [arg4] and the Device ID is [arg5]. The Physical slot number is [arg6].Error
FQXSFIO0014JA bad option ROM checksum was detected for the device found at Bus [arg1] Device [arg2] Function [arg3]. The Vendor ID for the device is [arg4] and the Device ID is [arg5]. The physical slot number is [arg6].Error
FQXSFIO0017MIFM: Error communicating with the XCC - IFM may not be deployed correctly.Error
FQXSFIO0019JPCIe Resource Conflict [arg1].Error
FQXSFIO0024MAn error has been detected by the IEH on processor [arg1]. The type of IEH is [arg2]. The index of the IEH is [arg3]. The value of IehErrorStatus register is [arg4]. Please check error logs for additional downstream device error data.Error
FQXSFIO0025MAn error has been detected by the IIO on processor [arg1]. The index of the IIO stack is [arg2]. The type of IIO Internal Error is [arg3]. Please check error logs for additional downstream device error data.Error
FQXSFIO0035MAn Uncorrectable PCIe Error has Occurred at Segment 0x[arg1] Bus 0x[arg2] Device 0x[arg3] Function 0x[arg4]. The Vendor ID for the device is 0x[arg5] and the Device ID is 0x[arg6]. The physical [arg7] number is [arg8].Error
FQXSFMA0001MDIMM [arg1] has been disabled due to an error detected during POST. [arg2]Error
FQXSFMA0002MAn uncorrectable memory error has been detected on DIMM [arg1] at address [arg2]. [arg3]Error
FQXSFMA0003KA memory mismatch has been detected. Please verify that the memory configuration is valid. [arg1]Error
FQXSFMA0004NNo system memory has been detected. [arg1]Error
FQXSFMA0005NMemory is present within the system but could not be configured. Please verify that the memory configuration is valid. [arg1]Error
FQXSFMA0008MDIMM [arg1] has failed the POST memory test. [arg2]Error
FQXSFMA0009KInvalid memory configuration for Mirror Mode. Please correct memory configuration. [arg1]Error
FQXSFMA0010KInvalid memory configuration for Sparing Mode. Please correct memory configuration. [arg1]Error
FQXSFMA0023MError has occurred in NVDIMM flash. NVDIMM backup/restore may not operate correctly. [arg1]Error
FQXSFMA0024MError has occurred in NVDIMM Supercap. NVDIMM backup/restore may not operate correctly. [arg1]Error
FQXSFMA0025MNVDIMM Supercap has been disconnected. NVDIMM will lose its backup ability until this is corrected. [arg1]Error
FQXSFMA0027KInvalid memory configuration (Unsupported DIMM Population) detected. Please verify memory configuration is valid.Error
FQXSFMA0028KMemory Capacity exceeds CPU limit. [arg1]Error
FQXSFMA0056MAn uncorrected recoverable memory error has been detected on DIMM [arg1] at address [arg2].[arg3]Error
FQXSFMA0066MMemory address parity error occurred on CPU [arg1] channel [arg2] with DIMM [arg3].Error
FQXSFPU0001NAn unsupported processor has been detected.Error
FQXSFPU0002NAn invalid processor type has been detected.Error
FQXSFPU0003KA processor mismatch has been detected between one or more processors in the system.Error
FQXSFPU0004KA discrepancy has been detected in the number of cores reported by one or more processors within the system.Error
FQXSFPU0005KA mismatch between the maximum allowed UPI link speed has been detected for one or more processors.Error
FQXSFPU0006KA power segment mismatch has been detected for one or more processors.Error
FQXSFPU0007KProcessors have mismatched Internal DDR FrequencyError
FQXSFPU0008KA core speed mismatch has been detected for one or more processors.Error
FQXSFPU0009KAn external clock frequency mismatch has been detected for one or more processors.Error
FQXSFPU0010KA cache size mismatch has been detected for one or more processors.Error
FQXSFPU0011KA cache type mismatch has been detected for one or more processors.Error
FQXSFPU0012KA cache associativity mismatch has been detected for one or more processors.Error
FQXSFPU0013KA processor model mismatch has been detected for one or more processors.Error
FQXSFPU0014NA processor family mismatch has been detected for one or more processors.Error
FQXSFPU0015KA processor stepping mismatch has been detected for one or more processors.Error
FQXSFPU0016NA processor within the system has failed the BIST.Error
FQXSFPU0017GA processor microcode update failed.Error
FQXSFPU0018NCATERR(IERR) has asserted on processor [arg1].Error
FQXSFPU0019NAn uncorrectable error has been detected on processor [arg1].Error
FQXSFPU0027NSystem uncorrectable error has occurred on Processor [arg1] Core [arg2] MC bank [arg3] with MC Status [arg4], MC Address [arg5], and MC Misc [arg6].Error
FQXSFPU0030NA firmware fault has been detected in the UEFI image.Error
FQXSFPU0031NThe number of POST attempts has reached the value configured in F1 setup.The system has booted with default UEFI settings. User specified settings have been preserved and will be used on subsequent boots unless modified before rebooting.Error
FQXSFPU0034LThe TPM could not be initialized properly.Error
FQXSFPU0035NA 3-strike timeout has occurred on processor [arg1].Error
FQXSFPU4056MTPM card is changed, need install back the original TPM card which shipped with the system.Error
FQXSFSM0008MBoot permission timeout detected.Error