Hardware replacement procedures
This section provides installation and removal procedures for all serviceable system components. Each component replacement procedure references any tasks that need to be performed to gain access to the component being replaced.
Attention
Two people and one lifting device on site that can support up to 400 lb (181 kg) are required to perform the replacement procedure of certain parts. If you do not already have a lifting device available, Lenovo offers the Genie Lift GL-8 material lift that can be purchased at Data Center Solution Configurator. Make sure to include the Foot-release brake and the Load Platform when ordering the Genie Lift GL-8 material lift.
- Installation Guidelines
Before installing components in your server, read the installation guidelines. - Memory module installation rules and order
Memory modules must be installed in a specific order based on the memory configuration that you implement and the number of processors and memory modules installed in the server. - Power on and power off the server
Follow the instructions in this section to power on and power off the server. - Chassis replacement
Follow instructions in this section to remove and install the chassis. - 2.5-inch hot-swap drive replacement
Follow instructions in this section to remove and install a 2.5-inch hot-swap drive. - 2.5-inch drive backplane replacement (trained technician only)
Follow instructions in this section to remove and install a 2.5-inch drive backplane. - 2U compute shuttle replacement (trained technician only)
Follow instructions in this section to remove and install the 2U compute shuttle. - 8U GPU shuttle replacement (trained technician only)
Follow instructions in this section to remove and install the 8U GPU shuttle. - Cable cover replacement (trained technician only)
Follow instructions in this section to remove and install the cable cover. - CMOS battery (CR2032) replacement
Follow instructions in this section to remove and install the CMOS battery (CR2032). - Fan replacement
Follow instructions in this section to remove or install a fan. - Fan control board assembly replacement (trained technician only)
Follow instructions in this section to remove or install a fan control board assembly. - GPU air baffle replacement (trained technician only)
Follow instructions in this section to remove and install the GPU air baffle. - GPU air duct replacement (trained technician only)
Follow instructions in this section to remove and install a GPU air duct. - GPU baseboard replacement (trained technician only)
Follow instructions in this section to remove or install the GPU baseboard. - GPU complex replacement (trained technician only)
Follow instructions in this section to remove or install the GPU complex. - GPU complex adapter plate replacement (trained technician only)
Follow instructions in this section to remove or install the GPU complex adapter plate. - GPU and heat sink module replacement (trained technician only)
Follow instructions in this section to remove or install a GPU and heat sink module. - HMC card replacement (trained technician only)
Follow instructions in this section to remove or install the HMC card. - Integrated diagnostics panel replacement
Follow instructions in this section to remove or install the integrated diagnostics panel. - I/O cover replacement (trained technician only)
Follow instructions in this section to remove and install the I/O cover. - M.2 backplane and M.2 drive replacement (trained technician only)
Follow instructions in this section to remove and install the M.2 backplane and an M.2 drive. - Memory module replacement (trained technician only)
Use the following procedures to remove and install a memory module. - MicroSD card replacement (trained technician only)
Follow instructions in this section to remove and install the MicroSD card. - OCP module replacement
Follow instructions in this section to remove and install the OCP module. - PCIe adapter replacement (trained technician only)
Follow instructions in this section to remove and install a PCIe adapter. - PCIe riser air baffle replacement (trained technician only)
Follow instructions in this section to remove and install a PCIe riser air baffle. - PCIe riser assembly replacement (trained technician only)
Follow instructions in this section to remove and install a PCIe riser assembly. - PCIe switch board and heat sink replacement (trained technician only)
Follow instructions in this section to remove and install the PCIe switch board and a PCIe switch board heat sink. - PCIe switch cable harness replacement (trained technician only)
Follow instructions in this section to remove and install a PCIe switch cable harness. - PCIe switch shuttle replacement (trained technician only)
Follow instructions in this section to remove and install the PCIe switch shuttle. - Power complex replacement (trained technician only)
Follow instructions in this section to remove and install the power complex. - Power distribution board replacement (trained technician only)
Follow instructions in this section to remove and install the power distribution board. - Power interface board replacement (trained technician only)
Follow instructions in this section to remove and install the power interface board. - Power supply unit replacement
Follow instructions in this section to remove or install a power supply unit. - Processor air baffle replacement (trained technician only)
Follow instructions in this section to remove and install the processor air baffle. - Processor and heat sink replacement (trained technician only)
Follow instructions in this section to remove and install a processor and a heat sink. - PSU cage replacement (trained technician only)
Follow instructions in this section to remove and install the PSU cage. - PSU interposer replacement (trained technician only)
Follow instructions in this section to remove and install the PSU interposer. - System board assembly replacement (trained technician only)
Follow instructions in this section to remove and install the system board assembly. - Complete the parts replacement
Go through the checklist to complete parts replacement
Give documentation feedback