Skip to main content

Front view

This section contains information about the controls, LEDs, and connectors on the front of the server.

Front view of 2.5-inch drive configuration

Note
Depending on the configuration, your server might be slightly different from the image.
Figure 1. Front view of 2.5-inch drive configuration
Front view of 2.5-inch drive configuration
Table 1. Components on the front view
1 VGA connector8 Network activity LED (green)
2 External diagnostics connector9 System ID button/LED (blue)
3 2.5-inch drive bays (bay 0 to 23)10 System error LED (yellow)
4 Drive activity LED (green)11 USB 2.0 connector with Lenovo XClarity Controller management
5 Drive status LED (yellow)12 USB 3.2 Gen 1 (5 Gbps) connector
6 Pull-out information tab13 Rack release latches
7 Power button/LED (green)14 2.5-inch drive bays (bay 24 to 47)

1 VGA connector

Connect a monitor to this connector.

2 External diagnostics connector

Connect the external diagnostics handset to this connector. See External Diagnostics Handset for more details.

3 / 14 2.5-inch drive bays

Install 2.5-inch drives to these bays. See Install a 2.5-inch hot-swap drive.

4 Drive activity LED (green)

Each hot-swap drive comes with an activity LED. When this LED is flashing, it indicates that the drive is in use.

5 Drive status LED (yellow)

The drive status LED indicates the following status:
  • The LED is lit: the drive has failed.

  • The LED is flashing slowly (once per second): the drive is being rebuilt.

  • The LED is flashing rapidly (three times per second): the drive is being identified.

6 Pull-out information tab

This tab contains network information such as MAC address and XCC network access label.

7 Power button/LED (green)

Press this button to turn the server on and off manually. The states of the power LED are as follows:
StatusColorDescription
OffNonePower is not present, or the power supply has failed.
Fast blinking (about four flashes per second)Green
  • The server is off, but the XClarity Controller is initializing, and the server is not ready to be powered on.

  • System-board-assembly power has failed.

Slow blinking (about one flash per second)GreenThe server is off and is ready to be powered on (standby state).
Solid onGreenThe server is on and running.

8 Network Activity LED (green)

The network activity LED helps you identify the network connectivity and activity.
StatusColorDescription
OnGreenThe server is connected to a network.
BlinkingGreenThe network is connected and active.
OffNoneThe server is disconnected from the network.

9 System ID button/LED (blue)

Use this system ID button and the blue system ID LED to visually locate the server. Each time you press the system ID button, the state of the system ID LED changes. The LED can be changed to on, blinking, or off. You can also use the Lenovo XClarity Controller or a remote management program to change the state of the system ID LED to assist in visually locating the server among other servers.

10 System error LED (yellow)

The system error LED helps you to determine if there are any system errors.
StatusColorDescriptionAction
OnYellow
An error has been detected on the server. Causes might include one or more of the following errors:
  • The temperature of the server reached the non-critical temperature threshold.

  • The voltage of the server reached the non-critical voltage threshold.

  • A fan has been detected to be running at low speed.

  • The power supply has a critical error.

  • The power supply is not connected to the power.

Check system logs or internal error LEDs to identify the failed part.

OffNoneThe server is off or the server is on and is working correctly.None.

11 USB 2.0 connector with Lenovo XClarity Controller management

Connect a USB 2.0 device, such as a mouse, keyboard, or other devices, to this connector.
Note
This is the only USB port that supports USB automation update of the firmware and RoT security module.

Connection to Lenovo XClarity Controller is primarily intended for users with a mobile device running the Lenovo XClarity Controller mobile application. When a mobile device is connected to this USB port, an Ethernet over USB connection is established between the mobile application running on the device and the Lenovo XClarity Controller.

Select Network in BMC Configuration to view or modify settings.

Four types of settings are available:

  • Host only mode

    In this mode, the USB port is always solely connected to the server.

  • BMC only mode

    In this mode, the USB port is always solely connected to Lenovo XClarity Controller.

  • Shared mode: owned by BMC

    In this mode, connection to the USB port is shared by the server and Lenovo XClarity Controller, while the port is switched to Lenovo XClarity Controller.

  • Shared mode: owned by host

    In this mode, connection to the USB port is shared by the server and Lenovo XClarity Controller, while the port is switched to the server.

12 USB 3.2 Gen 1 (5 Gbps) connector

The USB 3.2 Gen 1 (5 Gbps) connector can be used to attach a USB-compatible device, such as a USB keyboard, USB mouse, or USB storage device.

13 Rack release latches

Press on the latch on both sides to disengage the server from the rack and slide it out.