Skip to main content

Parts list

Use the parts list to identify each of the components that are available for your server.

Note
Depending on the model, your server might look slightly different from the illustration.
Figure 1. Server components
Graphic showing all parts associated with the server
The parts listed in the following table are identified as one of the following:

  • Tier 1 customer replaceable unit (CRU): Replacement of Tier 1 CRUs is your responsibility. If Lenovo installs a Tier 1 CRU at your request with no service agreement, you will be charged for the installation.

  • Tier 2 customer replaceable unit (CRU): You may install a Tier 2 CRU yourself or request Lenovo to install it, at no additional charge, under the type of warranty service that is designated for your server.

  • Field replaceable unit (FRU): FRUs must be installed only by trained service technicians.

  • Consumable and Structural parts: Purchase and replacement of consumable and structural parts is your responsibility. If Lenovo acquires or installs a structural component at your request, you will be charged for the service.

Table 1. Parts listing
IndexDescriptionTier 1 CRUTier 2 CRUFRUConsumable and Structural parts

For more information about ordering the parts shown in Figure 1:

Parts list

It is highly recommended that you check the power summary data for your server using Lenovo Capacity Planner before purchasing any new parts.

1Power distribution board  √ 
2Power distribution board cover   √
3Expansion drive cage√   
4Optical drive cage and 5.25-inch drive bay adapter√   
5Front panel board assembly √  
6EIA brackets√   
7Security door√   
8Tape/Optical drive filler cover and tape drive filler   √
95.25-inch optical disk drive√   
105.25-inch LTO/RDX tape drive√   
11Slim optical drive√   
122.5-inch drive√   
133.5-inch drive tray with 2.5-inch to 3.5-inch drive adapter√   
143.5-inch simple-swap drive√   
153.5-inch hot-swap drive√   
16Filler, 3.5-inch storage drive (single bay)   √
17Filler, 3.5-inch storage drive (four bay)   √
182.5-inch hot-swap drive√   
19Filler, 2.5-inch storage drive (single bay)   √
20Filler, 2.5-inch storage drive (eight bay)   √
21Bracket kit (drive retainer and PCIe bracket)   √
223.5-inch simple-swap drive backplate√   
233.5-inch hot-swap drive backplane√   
242.5-inch hot-swap drive backplane√   
25Front bezel√   
26Foot stand   √
27Chassis  √ 
28System board  √ 
29M.2 boot adapter√   
30M.2 retainer clip√   
31M.2 drive√   
32Internal CFF RAID adapter√   
33TPM card (for Chinese Mainland only)  √ 
34CMOS battery (CR2032)   √
35DIMM√   
36PHM module (heatsink, carrier, processor)  √ 
37Heat sink Torx T30 nut √  
38Flash power module√   
39Server cover√   
40Air baffle   √
41T4 filler√   
42Full-length GPU filler   √
43Screw kit   √
44Cables√   
45Suction cup (for NVLink bridge)   √
46NVLink bridge√   
47Full-length GPU adapter√   
48PCIe adapter√   
49Fan module√   
50Fan filler   √
51Intrusion switch√   
52External LCD diagnostics handset√   
53A2/L4 GPU air ducts√   
54Full-length PCIe adapter holders   √
55Fan cage   √
56Power supply unit√   
57PSU filler√   
  • Power cords
    Several power cords are available, depending on the country and region where the server is installed.