Step 6. Install and configure the Lenovo XClarity Administrator virtual appliance (Citrix)

Install and configure the XClarity Administrator virtual appliance on the Citrix host that was just installed.

Procedure

To install the XClarity Administrator virtual appliance, complete the following steps.

1. Download the XClarity Administrator virtual-appliance image from the XClarity Administrator download webpage to a client workstation. Log on to the Web site, and then use the access key that was given to you to download the image.

   For Citrix, download the image in VHD format.

   Note

   Ensure that the client workstation is on the same network as the host.
2. Install and configure the virtual appliance on the host.
   1. From the Citrix hypervisor, right-click the managed Citrix from the left navigation pane, and click Import. The Import dialog is displayed.
   2. Click Browse, select the XClarity Administrator VHD file. Then, click Next.
   3. On the Define Virtual Machine page, specify a name for the XClarity Administrator virtual machine, number of processors, and the amount of memory to initially allocate to the virtual machine. Then, click Next.
   4. On the Location page, select the Citrix where you want to place the virtual machine. Then, click Next.
   5. On the Storage page, select the Citrix disk drive to place the virtual-machine image. Then, click Next.
      Important

      Ensure that the disk drive has a minimum of 192 GB of free space.
   6. On the Networking page, select the virtual network switch to which the XClarity Administrator eth0 port is connected. Then, click Next.
   7. On the OS Fixup Settings page, use the default settings. Click Next.
   8. On the Transfer VM Settings page, select the Citrix network to use for the transfer of the virtual machine to the Citrix disk for installation. Then, click Next.
      Important

      Do not use the static IP settings in this page.
   9. Click Finish to start XClarity Administrator virtual machine installation in the Citrix.
   10. Wait for the import and installation to complete.
   11. Set up the second XClarity Administrator interface.

       1. Expand the virtual machine in the left navigation, and then click the Networking tab in the right content pane. The Virtual Network Interface page is displayed.

       2. Click Add interface to add the network interface to the virtual machine. The Add Virtual Interface dialog is displayed.

       3. Specify the network and MAC addresses for the virtual interface, and click Add.

   12. From the Citrix hypervisor, right-click the virtual machine, and then click Start.

       When the virtual machine is started, the IPv4 and IPv6 addresses are listed for each interface, as shown in the following example.

       The XClarity Administrator eth0 management port uses a DHCP IP address by default. At the end of the XClarity Administrator boot process, you can choose to set a static IP address for the eth0 management port by entering 1 when prompted, as shown in the example below. The prompt is available for 150 seconds, until the login prompt is displayed. To proceed to the login prompt without delay, enter x at the prompt.

       Important

       • When changing the static IP address settings, you have a maximum of 60 seconds to enter the new settings. Ensure that you have the required IP information before continuing.

         • For IPv4 settings, you must have the IP address, subnet mask, and gateway IP address

         • For IPv6 settings, you must have the IP address and prefix length

       • If you are not using a DHCP server, you can use a configuration file to specify the IP settings for the XClarity Administrator eth0 management port. that you want to use to access the XClarity Administrator. For more information, see the What to do next section below.

       • If you change the IP address settings from the console, XClarity Administrator is restarted to apply the new settings.

       • No action is required to log in. Ignore the console login message. The console interface is not for customer use.

       • You might see the message TCP: eth0: Driver has suspect GRO implementation, TCP performance may be compromised on the console. The performance of the virtual machine is not impacted, and you can ignore this warning.

       Attention

       Changing the IP address of the XClarity Administrator management port after managing devices might cause the devices to be placed in offline state in XClarity Administrator. If you choose to change the IP address after XClarity Administrator is up and running, ensure that all devices are unmanaged before changing the IP address.

       ------------------------------------------
       Lenovo XClarity Administrator  Version x.x.x
       ------------------------------------------
       
       eth0   flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500  metric 1
                inet 192.0.2.10  netmask 255.255.255.0  broadcast 192.0.2.55
                inet6 2001:db8:56ff:fe80:bea3  prefixlen 64   scopeid 0x20<link>
                ether 00:15:5d:0c:d1:92    txqueuelen 1000 (Ethernet)
                RX errors 0  dropped 0  overruns 0  frame 0
       
       eth1   flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500  metric 1
                inet 192.0.2.20  netmask 255.255.255.0  broadcast 192.0.2.130
                inet6 2001:db8:56ff:fe80:bea3  prefixlen 64  scopeid 0x20<link>
       
       ===========================================================================
       ===========================================================================
       
       You have 150 seconds to change IP settings. Enter one of the following:
         1. To set a static IP address for Lenovo XClarity virtual appliance eth0 port
         2. To use a DHCP address for Lenovo XClarity virtual appliance eth0 port
         x. To continue without changing IP settings
         ... ...