Parts list
Use the parts list to identify each of the components that are available for your server.
Go to Lenovo Data Center Support and navigate to the support page for your server.
Click .
Enter the serial number to view a listing of parts for your server.
It is highly recommended that you check the power summary data for your server using Lenovo Capacity Planner before purchasing any new parts.
For more information about ordering the parts shown in the Figure 1 or Figure 2:
T1: Tier 1 customer replaceable unit (CRU). Replacement of Tier 1 CRUs is your responsibility. If Lenovo installs a Tier 1 CRU at your request with no service agreement, you will be charged for the installation.
T2: Tier 2 customer replaceable unit (CRU). You may install a Tier 2 CRU yourself or request Lenovo to install it, at no additional charge, under the type of warranty service that is designated for your server.
F: Field replaceable unit (FRU). FRUs must be installed only by trained service technicians.
C: Consumable and Structural parts. Purchase and replacement of consumable and structural parts (components, such as a filler or bezel) is your responsibility. If Lenovo acquires or installs a structural component at your request, you will be charged for the service.
2.5-inch drive model
| Index | Description | Type |
|---|---|---|
For more information about ordering parts:
| ||
| 1 | Top cover | T1 |
| 2 | M.2 retainer clip | T1 |
| 3 | PCIe riser assembly | T1 |
| 4 | PCIe adapter | T1 |
| 5 | M.2 boot adapter | T1 |
| 6 | PCIe adapter for M.2 boot adapter | T1 |
| 7 | Chassis for CRPS hot-swap power supply unit | F |
| 8 | CMOS battery (CR2032) | C |
| 9 | Air baffle | T1 |
| 10 | Fan | T1 |
| 11 | Power distribution board cover | T1 |
| 12 | Chassis for fixed power supply | F |
| 13 | CRPS hot-swap power supply unit | T2 |
| 14 | Fixed power supply unit | T2 |
| 15 | Intrusion switch | T1 |
| 16 | Rack latches | T1 |
| 17 | CRPS hot-swap power supply filler | C |
| 18 | Cables | T1 |
| 19 | Front I/O module | T2 |
| 20 | VGA cable | T1 |
| 21 | Security bezel | T1 |
| 22 | Flash power module | T1 |
| 23 | M.2 drive | T1 |
| 24 | Power distribution board | T2 |
| 25 | Firmware and RoT security module | F |
| 26 | Processor | F |
| 27 | System board | F |
| 28 | Heat sink | F |
| 29 | Memory module | T1 |
| 30 | 2.5-inch hot-swap drive | T1 |
| 31 | Drive filler | C |
| 32 | Backplane, eight 2.5-inch hot-swap drives | T1 |
| 33 | Backplane, ten 2.5-inch hot-swap drives | T1 |
3.5-inch drive model
| Index | Description | Type |
|---|---|---|
For more information about ordering parts:
| ||
| 1 | Top cover | T1 |
| 2 | M.2 retainer clip | T1 |
| 3 | PCIe riser assembly | T1 |
| 4 | PCIe adapter | T1 |
| 5 | M.2 boot adapter | T1 |
| 6 | PCIe adapter for M.2 boot adapter | T1 |
| 7 | Chassis for redundant power supply | F |
| 8 | CMOS battery (CR2032) | C |
| 9 | Air baffle | T1 |
| 10 | Fan | T1 |
| 11 | Power distribution board cover | T1 |
| 12 | Chassis for fixed power supply | F |
| 13 | Redundant power supply unit | T1 |
| 14 | Fixed power supply unit | T2 |
| 15 | Intrusion switch | T2 |
| 16 | Rack latches | T1 |
| 17 | CRPS hot-swap power supply filler | C |
| 18 | Cables | T1 |
| 19 | Front I/O module | T1 |
| 20 | VGA cable | T1 |
| 21 | Security bezel | T1 |
| 22 | Flash power module | T1 |
| 23 | M.2 drive | T1 |
| 24 | Power distribution board | T2 |
| 25 | Firmware and RoT security module | F |
| 26 | Processor | F |
| 27 | System board | F |
| 28 | Heat sink | F |
| 29 | Memory module | T1 |
| 30 | 3.5-inch hot-swap drive | T1 |
| 31 | 3.5-inch simple-swap drive | T1 |
| 32 | Drive filler | C |
| 33 | 2.5-inch simple-swap drive with 3.5-inch drive tray | T1 |
| 34 | Backplane, four 3.5-inch hot-swap drives | T1 |
| 35 | Backplate, four 3.5-inch simple-swap drives (connects to RAID card) | T1 |
| 36 | Backplate, four 3.5-inch simple-swap drives (connects to onboard connectors) | T1 |
| 37 | Backplate, two 3.5-inch simple-swap SATA drives and two NVMe drives (connects to onboard connectors) | T1 |