Skip to main content

Observable problems

Use this information to solve observable problems.

The server immediately displays the POST Event Viewer when it is turned on​

Complete the following steps until the problem is solved.

  1. Correct any errors that are indicated by the system LEDs and diagnostics display.

  2. Make sure that the server supports all the processors and that the processors match in speed and cache size.

    You can view processor details from system setup.

    To determine if the processor is supported for the server, see Lenovo ServerProven website.

  3. (Trained technicians only) Make sure that processor 1 is seated correctly.

  4. (Trained technicians only) Remove processor 2 and restart the server.

  5. Replace the following components one at a time, in the order shown, restarting the server each time:

    1. (Trained technicians only) Processor

    2. (Trained technicians only) System board

Server is unresponsive (POST is complete and operating system is running)​

Complete the following steps until the problem is solved.

  • If you are in the same location as the compute node, complete the following steps:

    1. If you are using a KVM connection, make sure that the connection is operating correctly. Otherwise, make sure that the keyboard and mouse are operating correctly.

    2. If possible, log in to the compute node and verify that all applications are running (no applications are hung).

    3. Restart the compute node.

    4. If the problem remains, make sure that any new software has been installed and configured correctly.

    5. Contact your place of purchase of the software or your software provider.

  • If you are accessing the compute node from a remote location, complete the following steps:

    1. Make sure that all applications are running (no applications are hung).

    2. Attempt to log out of the system and log back in.

    3. Validate the network access by pinging or running a trace route to the compute node from a command line.

      1. If you are unable to get a response during a ping test, attempt to ping another compute node in the enclosure to determine whether it is a connection problem or compute node problem.

      2. Run a trace route to determine where the connection breaks down. Attempt to resolve a connection issue with either the VPN or the point at which the connection breaks down.

    4. Restart the compute node remotely through the management interface.

    5. If the problem remains, verify that any new software has been installed and configured correctly.

    6. Contact your place of purchase of the software or your software provider.

Server is unresponsive (POST failed and cannot start System Setup)​

Configuration changes, such as added devices or adapter firmware updates, and firmware or application code problems can cause the server to fail POST (the power-on self-test).

If this occurs, the server responds in either of the following ways:

  • The server restarts automatically and attempts POST again.

  • The server hangs, and you must manually restart the server for the server to attempt POST again.

After a specified number of consecutive attempts (automatic or manual), the server reverts to the default UEFI configuration and starts System Setup so that you can make the necessary corrections to the configuration and restart the server. If the server is unable to successfully complete POST with the default configuration, there might be a problem with the system board.

You can specify the number of consecutive restart attempts in System Setup. Restart the server and press the key according to the on-screen instructions to display the LXPM system setup interface. For more information, see the Startup section in the LXPM documentation compatible with your server at Lenovo XClarity Provisioning Manager portal page. Then, click System Settings > Recovery and RAS > POST Attempts > POST Attempts Limit. Available options are 3, 6, 9, and disable.

Voltage planar fault is displayed in the event log​

Complete the following steps until the problem is solved.

  1. Revert the system to the minimum configuration. See Specifications for the minimally required number of processors and DIMMs.

  2. Restart the system.

    • If the system restarts, add each of the removed items one at a time and restart the system each time until the error occurs. Replace the item for which the error occurs.

    • If the system does not restart, suspect the system board.

Unusual smell​

Complete the following steps until the problem is solved.

  1. An unusual smell might be coming from newly installed equipment.
  2. If the problem remains, contact Lenovo Support.

Server seems to be running hot​

Complete the following steps until the problem is solved.

Multiple compute nodes or chassis:

  1. Make sure that the room temperature is within the specified range (see Specifications).

  2. Make sure that the fans are installed correctly.

  3. Update the UEFI and XCC to the latest versions.

  4. Make sure that the fillers in the server are installed correctly (see Hardware replacement procedures for detailed installation procedures).

  5. Use the IPMI command to ramp up the fan speed to the full fan speed to see whether the issue can be resolved.

    Note
    The IPMI raw command should only be used by trained technicians and each system has its own specific IPMI raw command.
  6. Check the management processor event log for rising temperature events. If there are no events, the compute node is running within normal operating temperatures. Note that you can expect some variation in temperature.

Cracked parts or cracked chassis​

Contact Lenovo Support.