Network Boot Settings
Item | Description |
---|---|
MAC:XX:XX:XX:XX:XX:XX SlotXXX PCI X:XX:X:X | Set boot configuration parameters on MAC XX:XX:XX:XX:XX:XX PCI function address: Bus XX:Dev XX:Func XX See Table 2 below for more details. |
VLAN Configuration List: Slot X: VLAN Configuration Note For onboard devices, there is no “Slot X:” string. | Configure VLAN parameters. (MAC:XXXXXXXXXXXX) See Table 3 below for more details. |
IPv4 Configuration List: Slot X: IPv4 Network Configuration Note For onboard devices, there is no “Slot X:” string. | Configures IPv4 network parameters. (MAC:XXXXXXXXXXXX) See Table 4 below for more details. |
IPv6 Configuration List: Slot X: IPv6 Network Configuration Note For onboard devices, there is no “Slot X:” string. | Configure IPv6 network parameters. (MAC:XXXXXXXXXXXX) See Table 5 below for more details. |
MAC:Onboard PCI
Item | Options | Description |
---|---|---|
UEFI PXE Mode |
| Enable or disable NIC to include or skip boot attempt during generic PXE network boot. |
VLAN Configuration
On Enter Configuration Menu, press ENTER to enter the VLAN configuration menu.
Item | Options | Description |
---|---|---|
Create new VLAN | ||
VLAN ID | 0–4094 | Set the VLAN ID of a new VLAN or an existing VLAN. The valid value is 0–4094. |
Priority | 0–7 | Set 802.1Q priority. The valid value is 0–7. |
Add VLAN | N/A | Create a new VLAN or updates an existing VLAN. |
Configured VLAN list | ||
Lists of the configured VLANs. Only appears when VLANs are configured. Example: VLAN ID: X, Priority:X | Check box:
| Select a VLAN from the list to remove it. |
Remove VLAN | N/A | Remove selected VLANs. |
IPv4 Network Configuration
Item | Options | Description |
---|---|---|
Configured | Check box:
| Indicates whether the network address is configured successfully or not. |
Save Changes and Exit | N/A | Save changes and exit. |
IPv6 Network Configuration
On Enter Configuration Menu, press ENTER to enter the IPv6 network configuration menu.
Item | Options | Description |
---|---|---|
Interface Name | N/A | Name of the network interface |
Interface Type | N/A | Interface type of the network interface, defined in RFC1700 |
MAC address | XX-XX-XX-XX-XX-XX | Hardware address of the network interface |
Host address | XXXX::XXXX:XXXX:XXXX:XXXX/XX | List of host addresses, which contains the local IPv6 addresses and the corresponding prefix length information |
Route Table | XXXX::/64>>:: | Route table of the IPv6 network stack runs on this interface |
Gateway addresses | N/A | List of current gateway IPv6 addresses |
DNS addresses | N/A | List of current gateway DNS addresses |
Interface ID | N/A | The 64 bit alternative interface ID for the device. The string is colon separated. e.g. ff:dd:88:66:cc:1:2:3 |
DAD Transmit Count | N/A | Number of consecutive neighbor solicitation messages sent while performing duplicate address detection (DAD) on a tentative address. A value of “0” (zero) indicates that duplicate address detection is not performed. |
Policy |
| Specifies the network configuration policy. |
Advanced Configuration | N/A | Configures network settings for the interface manually, including IP addresses, gateway address, and DNS server address. |
Save Changes and Exit | N/A | Save changes and exit. |
Item | Options | Description |
---|---|---|
New IPv6 address | N/A | This item can be configured only when the Policy is set to manual. Separate the IP address with blank space to configure more than one address. e.g. 2002::1/64 2002::2/64 |
New Gateway addresses | N/A | This item can be configured only when the Policy is set to manual. Separate the IP address with blank space to configure more than one address. |
New DNS addresses | N/A | This item can be configured only when the Policy is set to manual. Separate the IP address with blank space to configure more than one address. |
Commit Changes and Exit | N/A | Commit changes and exit. |
Discard Changes and Exit | N/A | Discard changes and exit. |