UEFI events
UEFI error messages can be generated when the server starts up (POST) or while the server is running. UEFI error messages are logged in the Lenovo XClarity Controller event log in the server.
For each event code, the following fields are displayed:
Event identifier
An identifier that uniquely identifies an event.
Event description
The logged message string that appears for an event.
Explanation
Provides additional information to explain why the event occurred.
Severity
An indication of the level of concern for the condition. The severity is abbreviated in the event log to the first character. The following severities can be displayed:
Informational. The event was recorded for audit purposes, usually a user action or a change of states that is normal behavior.
Warning. The event is not as severe as an error, but if possible, the condition should be corrected before it becomes an error. It might also be a condition that requires additional monitoring or maintenance.
Error. The event is a failure or critical condition that impairs service or an expected function.
User Action
Indicates what actions you should perform to solve the event. Perform the steps listed in this section in the order shown until the problem is solved. If you cannot solve the problem after performing all steps, contact Lenovo Support.
UEFI events organized by severity
The following table lists all UEFI events, organized by severity (Information, Error, and Warning).FQXSFDD0001G : DRIVER HEALTH PROTOCOL: Missing Configuration. Requires Change Settings From F1.
DRIVER HEALTH PROTOCOL: Missing Configuration. Requires Change Settings From F1.FQXSFDD0002M : DRIVER HEALTH PROTOCOL: Reports 'Failed' Status Controller.
DRIVER HEALTH PROTOCOL: Reports 'Failed' Status Controller.FQXSFDD0003I : DRIVER HEALTH PROTOCOL: Reports 'Reboot' Required Controller.
DRIVER HEALTH PROTOCOL: Reports 'Reboot' Required Controller.FQXSFDD0004M : DRIVER HEALTH PROTOCOL: Reports 'System Shutdown' Required Controller.
DRIVER HEALTH PROTOCOL: Reports 'System Shutdown' Required Controller.FQXSFDD0005M : DRIVER HEALTH PROTOCOL: Disconnect Controller Failed. Requires 'Reboot'.
DRIVER HEALTH PROTOCOL: Disconnect Controller Failed. Requires 'Reboot'.FQXSFDD0006M : DRIVER HEALTH PROTOCOL: Reports Invalid Health Status Driver.
DRIVER HEALTH PROTOCOL: Reports Invalid Health Status Driver.FQXSFDD0007G : Security Key Lifecycle Manager (SKLM) IPMI Error.
Security Key Lifecycle Manager (SKLM) IPMI Error.FQXSFDD0012I : SATA Hard Drive Error: [arg1] was recovered.
SATA Hard Drive Error: [arg1] was recovered.FQXSFDD0012K : SATA Hard Drive Error: [arg1].
SATA Hard Drive Error: [arg1].FQXSFIO0005I : An intra-board UPI has been disabled on the link between processor [arg1] port [arg2] and processor [arg3]port [arg4] because of UPI topology downgrade.
An intra-board UPI has been disabled on the link between processor [arg1] port [arg2] and processor [arg3]port [arg4] because of UPI topology downgrade.FQXSFIO0005M : An intra-board UPI failure has been detected on the link between processor [arg1] port [arg2] and processor [arg3] port [arg4].
An intra-board UPI failure has been detected on the link between processor [arg1] port [arg2] and processor [arg3] port [arg4].FQXSFIO0006I : An inter-board UPI has been disabled on the link between processor [arg1] port [arg2] and processor [arg3]port [arg4] because of UPI topology downgrade.
An inter-board UPI has been disabled on the link between processor [arg1] port [arg2] and processor [arg3]port [arg4] because of UPI topology downgrade.FQXSFIO0006M : An inter-board UPI failure has been detected on the link between processor [arg1] port [arg2] and processor [arg3] port [arg4].
An inter-board UPI failure has been detected on the link between processor [arg1] port [arg2] and processor [arg3] port [arg4].FQXSFIO0007M : An error has been detected by the IIO on Bus [arg1]. The value of Global Fatal Error Status register is [arg2]. The value of Global Non-Fatal Error Status register is [arg3]. Please check error logs for additional downstream device error data.
An error has been detected by the IIO on Bus [arg1]. The value of Global Fatal Error Status register is [arg2]. The value of Global Non-Fatal Error Status register is [arg3]. Please check error logs for additional downstream device error data.FQXSFIO0008M : An intra-board UPI dynamic link width reduction has been detected on the link between processor [arg1] port [arg2] and processor [arg3] port [arg4].
An intra-board UPI dynamic link width reduction has been detected on the link between processor [arg1] port [arg2] and processor [arg3] port [arg4].FQXSFIO0009M : An inter-board UPI dynamic link width reduction has been detected on the link between processor [arg1] port [arg2] and processor [arg3] port [arg4].
An inter-board UPI dynamic link width reduction has been detected on the link between processor [arg1] port [arg2] and processor [arg3] port [arg4].FQXSFIO0010M : An Uncorrectable PCIe Error has Occurred at Bus [arg1] Device [arg2] Function [arg3]. The Vendor ID for the device is [arg4] and the Device ID is [arg5]. The physical [arg6] number is [arg7].
An Uncorrectable PCIe Error has Occurred at Bus [arg1] Device [arg2] Function [arg3]. The Vendor ID for the device is [arg4] and the Device ID is [arg5]. The physical [arg6] number is [arg7].FQXSFIO0011M : A PCIe parity error has occurred on Bus [arg1] Device [arg2] Function [arg3]. The Vendor ID for the device is [arg4] and the Device ID is [arg5]. The Physical slot number is [arg6].
A PCIe parity error has occurred on Bus [arg1] Device [arg2] Function [arg3]. The Vendor ID for the device is [arg4] and the Device ID is [arg5]. The Physical slot number is [arg6].FQXSFIO0012M : A PCIe system error has occurred on Bus [arg1] Device [arg2] Function [arg3]. The Vendor ID for the device is [arg4] and the Device ID is [arg5]. The Physical slot number is [arg6].
A PCIe system error has occurred on Bus [arg1] Device [arg2] Function [arg3]. The Vendor ID for the device is [arg4] and the Device ID is [arg5]. The Physical slot number is [arg6].FQXSFIO0013I : The device found at Bus [arg1] Device [arg2] Function [arg3] could not be configured due to resource constraints. The Vendor ID for the device is [arg4] and the Device ID is [arg5]. The physical slot number is [arg6].
The device found at Bus [arg1] Device [arg2] Function [arg3] could not be configured due to resource constraints. The Vendor ID for the device is [arg4] and the Device ID is [arg5]. The physical slot number is [arg6].FQXSFIO0014J : A bad option ROM checksum was detected for the device found at Bus [arg1] Device [arg2] Function [arg3]. The Vendor ID for the device is [arg4] and the Device ID is [arg5]. The physical slot number is [arg6].
A bad option ROM checksum was detected for the device found at Bus [arg1] Device [arg2] Function [arg3]. The Vendor ID for the device is [arg4] and the Device ID is [arg5]. The physical slot number is [arg6].FQXSFIO0015I : IFM: System reset performed to reset adapters.
IFM: System reset performed to reset adapters.FQXSFIO0016M : IFM: Reset loop avoided - Multiple resets not allowed.
IFM: Reset loop avoided - Multiple resets not allowed.FQXSFIO0017M : IFM: Error communicating with the XCC - IFM may not be deployed correctly.
IFM: Error communicating with the XCC - IFM may not be deployed correctly.FQXSFIO0018I : IFM: Configuration too large for compatibility mode.
IFM: Configuration too large for compatibility mode.FQXSFIO0019J : PCIe Resource Conflict.
PCIe Resource Conflict.FQXSFIO0020J : PCIe Isolation has occurred in PCIe slot [arg1]. The adapter may not operate correctly.
PCIe Isolation has occurred in PCIe slot [arg1]. The adapter may not operate correctly.FQXSFIO0021I : PCIe DPC software triggering occurred in physical [arg1] number [arg2].
PCIe DPC software triggering occurred in physical [arg1] number [arg2].FQXSFIO0021J : PCIe Error Recovery has occurred in physical [arg1] number [arg2]. The [arg3] may not operate correctly.
PCIe Error Recovery has occurred in physical [arg1] number [arg2]. The [arg3] may not operate correctly.FQXSFIO0022J : PCIe Link Width has degraded from [arg1] to [arg2] in physical [arg3] number [arg4].
PCIe Link Width has degraded from [arg1] to [arg2] in physical [arg3] number [arg4].FQXSFIO0023J : PCIe Link Speed has degraded from [arg1] to [arg2] in physical [arg3] number [arg4].
PCIe Link Speed has degraded from [arg1] to [arg2] in physical [arg3] number [arg4].FQXSFIO0024I : An error has been detected by the IEH on processor [arg1]. The type of IEH is [arg2]. The index of the IEH is [arg3]. The value of IehErrorStatus register is [arg4]. Please check error logs for additional downstream device error data.
An error has been detected by the IEH on processor [arg1]. The type of IEH is [arg2]. The index of the IEH is [arg3]. The value of IehErrorStatus register is [arg4]. Please check error logs for additional downstream device error data.FQXSFIO0024M : An error has been detected by the IEH on processor [arg1]. The type of IEH is [arg2]. The index of the IEH is [arg3]. The value of IehErrorStatus register is [arg4]. Please check error logs for additional downstream device error data.
An error has been detected by the IEH on processor [arg1]. The type of IEH is [arg2]. The index of the IEH is [arg3]. The value of IehErrorStatus register is [arg4]. Please check error logs for additional downstream device error data.FQXSFIO0025I : An error has been detected by the IIO on processor [arg1]. The index of the IIO stack is [arg2]. The type of IIO Internal Error is [arg3]. Please check error logs for additional downstream device error data.
An error has been detected by the IIO on processor [arg1]. The index of the IIO stack is [arg2]. The type of IIO Internal Error is [arg3]. Please check error logs for additional downstream device error data.FQXSFIO0025M : An error has been detected by the IIO on processor [arg1]. The index of the IIO stack is [arg2]. The type of IIO Internal Error is [arg3]. Please check error logs for additional downstream device error data.
An error has been detected by the IIO on processor [arg1]. The index of the IIO stack is [arg2]. The type of IIO Internal Error is [arg3]. Please check error logs for additional downstream device error data.FQXSFIO0035M : An Uncorrectable PCIe Error has Occurred at Segment 0x[arg1] Bus 0x[arg2] Device 0x[arg3] Function 0x[arg4]. The Vendor ID for the device is 0x[arg5] and the Device ID is 0x[arg6]. The physical [arg7] number is [arg8].
An Uncorrectable PCIe Error has Occurred at Segment 0x[arg1] Bus 0x[arg2] Device 0x[arg3] Function 0x[arg4]. The Vendor ID for the device is 0x[arg5] and the Device ID is 0x[arg6]. The physical [arg7] number is [arg8].FQXSFIO0036G : PCIe Correctable Error Threshold limit has been exceeded at Segment 0x[arg1] Bus 0x[arg2] Device 0x[arg3] Function 0x[arg4]. The Vendor ID for the device is 0x[arg5] and the Device ID is 0x[arg6]. The physical [arg7] number is [arg8].
PCIe Correctable Error Threshold limit has been exceeded at Segment 0x[arg1] Bus 0x[arg2] Device 0x[arg3] Function 0x[arg4]. The Vendor ID for the device is 0x[arg5] and the Device ID is 0x[arg6]. The physical [arg7] number is [arg8].FQXSFIO0041J : PCIe Leaky Bucket Event : [arg1] occurred at Segment [arg2] Bus [arg3] Device [arg4] Function [arg5]. The physical [arg6] number is [arg7].
PCIe Leaky Bucket Event : [arg1] occurred at Segment [arg2] Bus [arg3] Device [arg4] Function [arg5]. The physical [arg6] number is [arg7].FQXSFMA0001I : DIMM [arg1] Disable has been recovered. [arg2]
DIMM [arg1] Disable has been recovered. [arg2]FQXSFMA0001M : DIMM [arg1] has been disabled due to an error detected during POST. [arg2]
DIMM [arg1] has been disabled due to an error detected during POST. [arg2]FQXSFMA0002I : The uncorrectable memory error state has been cleared.
The uncorrectable memory error state has been cleared.FQXSFMA0002M : An uncorrectable memory error has been detected on DIMM [arg1] at address [arg2]. [arg3]
An uncorrectable memory error has been detected on DIMM [arg1] at address [arg2]. [arg3]FQXSFMA0003K : A memory mismatch has been detected. Please verify that the memory configuration is valid. [arg1]
A memory mismatch has been detected. Please verify that the memory configuration is valid. [arg1]FQXSFMA0004N : No system memory has been detected. [arg1]
No system memory has been detected. [arg1]FQXSFMA0005N : Memory is present within the system but could not be configured. Please verify that the memory configuration is valid. [arg1]
Memory is present within the system but could not be configured. Please verify that the memory configuration is valid. [arg1]FQXSFMA0006I : [arg1] DIMM [arg2] has been detected, the DIMM serial number is [arg3].
[arg1] DIMM [arg2] has been detected, the DIMM serial number is [arg3].FQXSFMA0007I : [arg1] DIMM number [arg2] has been replaced. [arg3]
[arg1] DIMM number [arg2] has been replaced. [arg3]FQXSFMA0008I : DIMM [arg1] POST memory test failure has been recovered. [arg2]
DIMM [arg1] POST memory test failure has been recovered. [arg2]FQXSFMA0008M : DIMM [arg1] has failed the POST memory test. [arg2]
DIMM [arg1] has failed the POST memory test. [arg2]FQXSFMA0009I : Invalid memory configuration for Mirror Mode has been recovered. [arg1]
Invalid memory configuration for Mirror Mode has been recovered. [arg1]FQXSFMA0009K : Invalid memory configuration for Mirror Mode. Please correct memory configuration. [arg1]
Invalid memory configuration for Mirror Mode. Please correct memory configuration. [arg1]FQXSFMA0010I : Invalid memory configuration for Sparing Mode has been recovered. [arg1]
Invalid memory configuration for Sparing Mode has been recovered. [arg1]FQXSFMA0010K : Invalid memory configuration for Sparing Mode. Please correct memory configuration. [arg1]
Invalid memory configuration for Sparing Mode. Please correct memory configuration. [arg1]FQXSFMA0011I : Memory population change detected. [arg1]
Memory population change detected. [arg1]FQXSFMA0012I : The PFA of DIMM [arg1] has been deasserted.
The PFA of DIMM [arg1] has been deasserted.FQXSFMA0014I : Memory spare copy initiated. [arg1]
Memory spare copy initiated. [arg1]FQXSFMA0015I : Memory spare copy has completed successfully. [arg1]
Memory spare copy has completed successfully. [arg1]FQXSFMA0016M : Memory spare copy failed. [arg1]
Memory spare copy failed. [arg1]FQXSFMA0023M : Error has occurred in NVDIMM flash. NVDIMM backup/restore may not operate correctly. [arg1]
Error has occurred in NVDIMM flash. NVDIMM backup/restore may not operate correctly. [arg1]FQXSFMA0024M : Error has occurred in NVDIMM Supercap. NVDIMM backup/restore may not operate correctly. [arg1]
Error has occurred in NVDIMM Supercap. NVDIMM backup/restore may not operate correctly. [arg1]FQXSFMA0025M : NVDIMM Supercap has been disconnected. NVDIMM will lose its backup ability until this is corrected. [arg1]
NVDIMM Supercap has been disconnected. NVDIMM will lose its backup ability until this is corrected. [arg1]FQXSFMA0026G : Multi-bit CE occurred on DIMM [arg1], need to restart the system for DIMM Self-healing to attempt post package repair (PPR).
Multi-bit CE occurred on DIMM [arg1], need to restart the system for DIMM Self-healing to attempt post package repair (PPR).FQXSFMA0026I : DIMM [arg1] Self-healing, attempt post package repair (PPR) succeeded. [arg2]
DIMM [arg1] Self-healing, attempt post package repair (PPR) succeeded. [arg2]FQXSFMA0027G : Multi-bit CE occurred on DIMM [arg1] different rows.[arg2]
Multi-bit CE occurred on DIMM [arg1] different rows.[arg2]FQXSFMA0027I : Invalid memory configuration (unsupported DIMM Population) recovered.
Invalid memory configuration (unsupported DIMM Population) recovered.FQXSFMA0027K : Invalid memory configuration (Unsupported DIMM Population) detected. Please verify memory configuration is valid.
Invalid memory configuration (Unsupported DIMM Population) detected. Please verify memory configuration is valid.FQXSFMA0027M : DIMM [arg1] Self-healing, attempt post package repair (PPR) failed at Rank [arg2] Sub Rank [arg3] Bank [arg4] Row [arg5] on Device [arg6]. [arg7]
DIMM [arg1] Self-healing, attempt post package repair (PPR) failed at Rank [arg2] Sub Rank [arg3] Bank [arg4] Row [arg5] on Device [arg6]. [arg7]FQXSFMA0028K : Memory Capacity exceeds CPU limit. [arg1]
Memory Capacity exceeds CPU limit. [arg1]FQXSFMA0028M : DIMM [arg1] Self-healing, attempt post package repair (PPR) exceeded DIMM level threshold [arg2] at Rank [arg3] Sub Rank [arg4] Bank [arg5] Row [arg6] on Device [arg7]. [arg8]
DIMM [arg1] Self-healing, attempt post package repair (PPR) exceeded DIMM level threshold [arg2] at Rank [arg3] Sub Rank [arg4] Bank [arg5] Row [arg6] on Device [arg7]. [arg8]FQXSFMA0029G : DIMM [arg1] Self-healing, attempt post package repair (PPR) failed with out of resource. [arg2]
DIMM [arg1] Self-healing, attempt post package repair (PPR) failed with out of resource. [arg2]FQXSFMA0029I : The PFA of DIMM [arg1] has been deasserted after applying PPR for this DIMM. [arg2]
The PFA of DIMM [arg1] has been deasserted after applying PPR for this DIMM. [arg2]FQXSFMA0047M : SPD CRC checking failed on DIMM [arg1]. [arg2]
SPD CRC checking failed on DIMM [arg1]. [arg2]FQXSFMA0048M : DIMM [arg1] disabled due to PMIC failure during POST, DIMM identifier is [arg2].
DIMM [arg1] disabled due to PMIC failure during POST, DIMM identifier is [arg2].FQXSFMA0049M : DIMM [arg1] disabled due to memory module power failure. DIMM [arg2] detected and good, DIMM [arg3] not detected.
DIMM [arg1] disabled due to memory module power failure. DIMM [arg2] detected and good, DIMM [arg3] not detected.FQXSFMA0050G : DRAM PFA threshold limit exceeded on DIMM [arg1] sub-channel [arg2] Rank [arg3] DRAM [arg4], DIMM identifier is [arg5].
DRAM PFA threshold limit exceeded on DIMM [arg1] sub-channel [arg2] Rank [arg3] DRAM [arg4], DIMM identifier is [arg5].FQXSFMA0052I : DIMM [arg1] has been disabled due to the error on DIMM [arg2].[arg3]
DIMM [arg1] has been disabled due to the error on DIMM [arg2].[arg3]FQXSFMA0053G : An uncorrected memory error has been recovered by mirror on DIMM [arg1] at address [arg2].[arg3]
An uncorrected memory error has been recovered by mirror on DIMM [arg1] at address [arg2].[arg3]FQXSFMA0053I : DIMM [arg1] re-enabled due to memory module combination updating.
DIMM [arg1] re-enabled due to memory module combination updating.FQXSFMA0053M : DIMM [arg1] not defective but disabled due to unsupported memory module combination on CPU [arg2].
DIMM [arg1] not defective but disabled due to unsupported memory module combination on CPU [arg2].FQXSFMA0054G : Mirror failover operation was successful. DIMM [arg1] has failed over to the mirrored DIMM [arg2].[arg3]
Mirror failover operation was successful. DIMM [arg1] has failed over to the mirrored DIMM [arg2].[arg3]FQXSFMA0055G : Mirror failover operation was unsuccessful. DIMM [arg1] cannot fail over again.[arg2]
Mirror failover operation was unsuccessful. DIMM [arg1] cannot fail over again.[arg2]FQXSFMA0056I : Uncorrected memory error occurred on DIMM [arg1] has been deasserted after performing post package repair. DIMM identifier is [arg2].
Uncorrected memory error occurred on DIMM [arg1] has been deasserted after performing post package repair. DIMM identifier is [arg2].FQXSFMA0056M : An uncorrected recoverable memory error has been detected on DIMM [arg1] at address [arg2].[arg3]
An uncorrected recoverable memory error has been detected on DIMM [arg1] at address [arg2].[arg3]FQXSFMA0057G : Page Retire PFA Threshold limit exceeded on DIMM [arg1] at address [arg2].[arg3] [arg4]
Page Retire PFA Threshold limit exceeded on DIMM [arg1] at address [arg2].[arg3] [arg4]FQXSFMA0058I : Memory mode is in flat mode, near memory/far memory ratio issue has recovered.
Memory mode is in flat mode, near memory/far memory ratio issue has recovered.FQXSFMA0058K : Near memory/far memory ratio (1:[arg1].[arg2]) for CPU high bandwidth memory cache mode configuration is not in recommended range (1:[arg3] - 1:[arg4]).
Near memory/far memory ratio (1:[arg1].[arg2]) for CPU high bandwidth memory cache mode configuration is not in recommended range (1:[arg3] - 1:[arg4]).FQXSFMA0059I : Bank sparing performed on CPU [arg1] high bandwidth memory channel [arg2] pseudo-channel [arg3].
Bank sparing performed on CPU [arg1] high bandwidth memory channel [arg2] pseudo-channel [arg3].FQXSFMA0060I : Partial cache line sparing performed on CPU [arg1] high bandwidth memory channel [arg2] pseudo-channel [arg3].
Partial cache line sparing performed on CPU [arg1] high bandwidth memory channel [arg2] pseudo-channel [arg3].FQXSFMA0061I : Uncorrected memory error occurred on CPU [arg1] high bandwidth memory has been deasserted after performing post package repair.
Uncorrected memory error occurred on CPU [arg1] high bandwidth memory has been deasserted after performing post package repair.FQXSFMA0061M : An uncorrected recoverable memory error occurred on CPU [arg1] high bandwidth memory channel [arg2] pseudo-channel [arg3].
An uncorrected recoverable memory error occurred on CPU [arg1] high bandwidth memory channel [arg2] pseudo-channel [arg3].FQXSFMA0062M : An uncorrectable memory error occurred on CPU [arg1] high bandwidth memory channel [arg2] pseudo-channel [arg3].
An uncorrectable memory error occurred on CPU [arg1] high bandwidth memory channel [arg2] pseudo-channel [arg3].FQXSFMA0063I : A correctable memory error handled by ADDDC on DIMM [arg1]. DIMM identifier is [arg2].
A correctable memory error handled by ADDDC on DIMM [arg1]. DIMM identifier is [arg2].FQXSFMA0064M : DIMM [arg1] disabled due to memory module power failure. DIMM [arg2] detected and good.
DIMM [arg1] disabled due to memory module power failure. DIMM [arg2] detected and good.FQXSFMA0065I : Multi-bit CE of DIMM [arg1] has been deasserted after performing post package repair. DIMM identifier is [arg2].
Multi-bit CE of DIMM [arg1] has been deasserted after performing post package repair. DIMM identifier is [arg2].FQXSFMA0065M : Memory address parity error occurred on CPU [arg1] high bandwidth memory channel [arg2] pseudo-channel [arg3].
Memory address parity error occurred on CPU [arg1] high bandwidth memory channel [arg2] pseudo-channel [arg3].FQXSFMA0066I : High bandwidth memory attempt post package repair (PPR) succeeded at CPU [arg1] high bandwidth memory channel [arg2] pseudo-channel [arg3].
High bandwidth memory attempt post package repair (PPR) succeeded at CPU [arg1] high bandwidth memory channel [arg2] pseudo-channel [arg3].FQXSFMA0066M : Memory address parity error occurred on CPU [arg1] channel [arg2] with DIMM [arg3].
Memory address parity error occurred on CPU [arg1] channel [arg2] with DIMM [arg3].FQXSFMA0067G : Errors per row counter threshold limit exceeded on DIMM [arg1] sub-channel [arg2] Rank [arg3] DRAM [arg4], need to restart the system for DIMM Self-healing to attempt post package repair (PPR), DIMM identifier is [arg5].
Errors per row counter threshold limit exceeded on DIMM [arg1] sub-channel [arg2] Rank [arg3] DRAM [arg4], need to restart the system for DIMM Self-healing to attempt post package repair (PPR), DIMM identifier is [arg5].FQXSFMA0067I : Errors per row counter threshold limit exceeded on DIMM [arg1] has been deasserted after performing post package repair. DIMM identifier is [arg2].
Errors per row counter threshold limit exceeded on DIMM [arg1] has been deasserted after performing post package repair. DIMM identifier is [arg2].FQXSFMA0067M : High bandwidth memory attempt post package repair (PPR) failed at CPU [arg1] high bandwidth memory channel [arg2] pseudo-channel [arg3].
High bandwidth memory attempt post package repair (PPR) failed at CPU [arg1] high bandwidth memory channel [arg2] pseudo-channel [arg3].FQXSFMA0068G : Multi-bit CE occurred on CPU [arg1] high bandwidth memory channel [arg2] pseudo-channel [arg3] different rows.
Multi-bit CE occurred on CPU [arg1] high bandwidth memory channel [arg2] pseudo-channel [arg3] different rows.FQXSFMA0068M : High bandwidth memory attempt post package repair (PPR) exceeded threshold at CPU [arg1] high bandwidth memory channel [arg2] pseudo-channel [arg3].
High bandwidth memory attempt post package repair (PPR) exceeded threshold at CPU [arg1] high bandwidth memory channel [arg2] pseudo-channel [arg3].FQXSFMA0069G : Page retire PFA threshold limit exceeded on high bandwidth memory CPU[arg1] at address [arg2]. [arg3]
Page retire PFA threshold limit exceeded on high bandwidth memory CPU[arg1] at address [arg2]. [arg3]FQXSFMA0070G : Post package repair failure and Bank sparing occurred during POST on CPU [arg1] high bandwidth memory channel [arg2] pseudo-channel [arg3].
Post package repair failure and Bank sparing occurred during POST on CPU [arg1] high bandwidth memory channel [arg2] pseudo-channel [arg3].FQXSFMA0071M : Bank sparing failure occurred during POST on CPU [arg1] high bandwidth memory channel [arg2] pseudo-channel [arg3].
Bank sparing failure occurred during POST on CPU [arg1] high bandwidth memory channel [arg2] pseudo-channel [arg3].FQXSFMA0072M : CPU [arg1] high bandwidth memory channel [arg2] disabled due to population error.
CPU [arg1] high bandwidth memory channel [arg2] disabled due to population error.FQXSFMA0073M : High bandwidth memory built-in self-test failed on CPU [arg1].
High bandwidth memory built-in self-test failed on CPU [arg1].FQXSFMA0074M : High bandwidth memory training failed on CPU [arg1].
High bandwidth memory training failed on CPU [arg1].FQXSFMA0075G : Multi-bit CE occurred on CPU [arg1] high bandwidth memory channel [arg2] pseudo-channel [arg3], need to restart the system for high bandwidth memory self-healing to attempt post package repair (PPR).
Multi-bit CE occurred on CPU [arg1] high bandwidth memory channel [arg2] pseudo-channel [arg3], need to restart the system for high bandwidth memory self-healing to attempt post package repair (PPR).FQXSFMA0075I : Multi-bit CE occurred on CPU [arg1] high bandwidth memory has been deasserted after performing post package repair.
Multi-bit CE occurred on CPU [arg1] high bandwidth memory has been deasserted after performing post package repair.FQXSFMA0076M : DIMM [arg1] is not supported, DIMM identifier is [arg2].
DIMM [arg1] is not supported, DIMM identifier is [arg2].FQXSFMA0077N : SMBus failure encountered when accessing to the SPD of DIMM [arg1]. [arg2].
SMBus failure encountered when accessing to the SPD of DIMM [arg1]. [arg2].FQXSFMA0078N : System firmware encountered fatal error [arg1] during memory initialization.
System firmware encountered fatal error [arg1] during memory initialization.FQXSFPU0001N : An unsupported processor has been detected.
An unsupported processor has been detected.FQXSFPU0002N : An invalid processor type has been detected.
An invalid processor type has been detected.FQXSFPU0003K : A processor mismatch has been detected between one or more processors in the system.
A processor mismatch has been detected between one or more processors in the system.FQXSFPU0004K : A discrepancy has been detected in the number of cores reported by one or more processors within the system.
A discrepancy has been detected in the number of cores reported by one or more processors within the system.FQXSFPU0005K : A mismatch between the maximum allowed UPI link speed has been detected for one or more processors.
A mismatch between the maximum allowed UPI link speed has been detected for one or more processors.FQXSFPU0006K : A power segment mismatch has been detected for one or more processors.
A power segment mismatch has been detected for one or more processors.FQXSFPU0007K : Processors have mismatched Internal DDR Frequency
Processors have mismatched Internal DDR FrequencyFQXSFPU0008K : A core speed mismatch has been detected for one or more processors.
A core speed mismatch has been detected for one or more processors.FQXSFPU0009K : An external clock frequency mismatch has been detected for one or more processors.
An external clock frequency mismatch has been detected for one or more processors.FQXSFPU0010K : A cache size mismatch has been detected for one or more processors.
A cache size mismatch has been detected for one or more processors.FQXSFPU0011K : A cache type mismatch has been detected for one or more processors.
A cache type mismatch has been detected for one or more processors.FQXSFPU0012K : A cache associativity mismatch has been detected for one or more processors.
A cache associativity mismatch has been detected for one or more processors.FQXSFPU0013K : A processor model mismatch has been detected for one or more processors.
A processor model mismatch has been detected for one or more processors.FQXSFPU0014N : A processor family mismatch has been detected for one or more processors.
A processor family mismatch has been detected for one or more processors.FQXSFPU0015K : A processor stepping mismatch has been detected for one or more processors.
A processor stepping mismatch has been detected for one or more processors.FQXSFPU0016N : A processor within the system has failed the BIST.
A processor within the system has failed the BIST.FQXSFPU0017G : A processor microcode update failed.
A processor microcode update failed.FQXSFPU0018N : CATERR(IERR) has asserted on processor [arg1].
CATERR(IERR) has asserted on processor [arg1].FQXSFPU0019N : An uncorrectable error has been detected on processor [arg1].
An uncorrectable error has been detected on processor [arg1].FQXSFPU0020I : The UEFI firmware image capsule signature is invalid.
The UEFI firmware image capsule signature is invalid.FQXSFPU0021I : The TPM physical presence state has been cleared.
The TPM physical presence state has been cleared.FQXSFPU0022G : The TPM configuration is not locked.
The TPM configuration is not locked.FQXSFPU0023G : Secure Boot Image Verification Failure Warning.
Secure Boot Image Verification Failure Warning.FQXSFPU0023I : Secure Boot Image Verification Failure has been cleared as no failure in this round boot.
Secure Boot Image Verification Failure has been cleared as no failure in this round boot.FQXSFPU0025I : The default system settings have been restored.
The default system settings have been restored.FQXSFPU0027N : System uncorrectable error has occurred on Processor [arg1] Core [arg2] MC bank [arg3] with MC Status [arg4], MC Address [arg5], and MC Misc [arg6].
System uncorrectable error has occurred on Processor [arg1] Core [arg2] MC bank [arg3] with MC Status [arg4], MC Address [arg5], and MC Misc [arg6].FQXSFPU0030N : A firmware fault has been detected in the UEFI image.
A firmware fault has been detected in the UEFI image.FQXSFPU0031N : The number of POST attempts has reached the value configured in F1 setup.The system has booted with default UEFI settings. User specified settings have been preserved and will be used on subsequent boots unless modified before rebooting.
The number of POST attempts has reached the value configured in F1 setup.The system has booted with default UEFI settings. User specified settings have been preserved and will be used on subsequent boots unless modified before rebooting.FQXSFPU0033G : Processor has been disabled.
Processor has been disabled.FQXSFPU0034L : The TPM could not be initialized properly.
The TPM could not be initialized properly.FQXSFPU0035N : A 3-strike timeout has occurred on processor [arg1].
A 3-strike timeout has occurred on processor [arg1].FQXSFPU0062F : System uncorrected recoverable error happened in Processor [arg1] Core [arg2] MC bank [arg3] with MC Status [arg4], MC Address [arg5], and MC Misc [arg6].
System uncorrected recoverable error happened in Processor [arg1] Core [arg2] MC bank [arg3] with MC Status [arg4], MC Address [arg5], and MC Misc [arg6].FQXSFPU4033F : TPM Firmware recovery is in progress. Please DO NOT power off or reset system.
TPM Firmware recovery is in progress. Please DO NOT power off or reset system.FQXSFPU4034I : TPM Firmware recovery is finished, rebooting system to take effect.
TPM Firmware recovery is finished, rebooting system to take effect.FQXSFPU4035M : TPM Firmware recovery failed. TPM chip may be damaged.
TPM Firmware recovery failed. TPM chip may be damaged.FQXSFPU4038I : TPM Firmware recovery successful.
TPM Firmware recovery successful.FQXSFPU4040M : TPM selftest has failed.
TPM selftest has failed.FQXSFPU4041I : TPM Firmware update is in progress. Please DO NOT power off or reset system.
TPM Firmware update is in progress. Please DO NOT power off or reset system.FQXSFPU4042I : TPM Firmware update is finished, rebooting system to take effect.
TPM Firmware update is finished, rebooting system to take effect.FQXSFPU4043G : TPM Firmware update aborted. System is rebooting...
TPM Firmware update aborted. System is rebooting...FQXSFPU4044I : The current TPM firmware version could not support TPM version toggling.
The current TPM firmware version could not support TPM version toggling.FQXSFPU4046I : TPM Firmware will be updated from TPM1.2 to TPM2.0.
TPM Firmware will be updated from TPM1.2 to TPM2.0.FQXSFPU4047I : TPM Firmware will be updated from TPM2.0 to TPM1.2.
TPM Firmware will be updated from TPM2.0 to TPM1.2.FQXSFPU4049I : TPM Firmware update successful.
TPM Firmware update successful.FQXSFPU4050G : Failed to update TPM Firmware.
Failed to update TPM Firmware.FQXSFPU4051G : Undefined TPM_POLICY found
Undefined TPM_POLICY foundFQXSFPU4052G : TPM_POLICY is not locked
TPM_POLICY is not lockedFQXSFPU4053G : System TPM_POLICY does not match the planar.
System TPM_POLICY does not match the planar.FQXSFPU4054G : TPM card logical binding has failed.
TPM card logical binding has failed.FQXSFPU4056M : TPM card is changed, need install back the original TPM card which shipped with the system.
TPM card is changed, need install back the original TPM card which shipped with the system.FQXSFPU4059I : User requested to skip freezing lock of AHCI-attached SATA drives. System UEFI accepted the request and will execute priot to OS boot.
User requested to skip freezing lock of AHCI-attached SATA drives. System UEFI accepted the request and will execute priot to OS boot.FQXSFPU4060I : Skipped freezing lock of AHCI-attached SATA drives.
Skipped freezing lock of AHCI-attached SATA drives.FQXSFPU4061I : Restored default locking behavior of AHCI-attached SATA drives.
Restored default locking behavior of AHCI-attached SATA drives.FQXSFPU4062I : CPU debugging is deactivated for DCI interface.
CPU debugging is deactivated for DCI interface.FQXSFPU4062M : CPU debugging is activated for DCI interface.
CPU debugging is activated for DCI interface.FQXSFPU4080I : Host Power-On password has been changed.
Host Power-On password has been changed.FQXSFPU4081I : Host Power-On password has been cleared.
Host Power-On password has been cleared.FQXSFPU4082I : Host Admin password has been changed.
Host Admin password has been changed.FQXSFPU4083I : Host Admin password has been cleared.
Host Admin password has been cleared.FQXSFPU4084I : Host boot order has been changed.
Host boot order has been changed.FQXSFPU4085I : Host WOL boot order has been changed.
Host WOL boot order has been changed.FQXSFPW0001L : CMOS has been cleared.
CMOS has been cleared.FQXSFSM0002N : Boot Permission denied by Management Module: System Halted.
Boot Permission denied by Management Module: System Halted.FQXSFSM0003N : Timed Out waiting on boot permission from Management Module: System Halted.
Timed Out waiting on boot permission from Management Module: System Halted.FQXSFSM0004M : An XCC communication failure has occurred.
An XCC communication failure has occurred.FQXSFSM0007I : The XCC System Event log (SEL) is full.
The XCC System Event log (SEL) is full.FQXSFSM0008M : Boot permission timeout detected.
Boot permission timeout detected.FQXSFSR0001M : [arg1] GPT corruption detected, DiskGUID: [arg2]
[arg1] GPT corruption detected, DiskGUID: [arg2]FQXSFSR0002I : [arg1] GPT corruption recovered, DiskGUID: [arg2]
[arg1] GPT corruption recovered, DiskGUID: [arg2]FQXSFSR0003G : The number of boot attempts has been exceeded. No bootable device found.
The number of boot attempts has been exceeded. No bootable device found.FQXSFTR0001L : An invalid date and time have been detected.
An invalid date and time have been detected.