Skip to main content

Rear operator panel LEDs

The rear operator panel of the server provides controls and LEDs.

Figure 1. Rear operator panel LEDs

Table 1. Rear operator panel LEDs
1 x86 WLAN activity LED (green)8 System Error LED (yellow)
2 XCC WLAN activity LED (green)9 Security LED (green)
3 Security LED (green)10 XCC WLAN activity LED (green)
4 System Error LED (yellow)11 x86 WLAN activity LED (green)
5 Bluetooth LED (blue)12 Power button with power status LED (green)
6 System ID LED (blue)13 System ID button with system ID LED (blue)
7 Power status LED (green)14 Bluetooth button with LED (blue)

1 11 x86 WLAN activity LED (green)​

The WLAN activity LED helps you identify the status of WLAN connection.

StatusColorDescription
OnGreenThe x86 WLAN is operating properly.
OffNoneThe x86 WLAN RF is turned off, or the x86 WLAN is not operating properly, or the server does not come with wireless module.

2 10 XCC WLAN activity LED (green)​

The WLAN activity LED helps you identify the status of WLAN connection.

StatusColorDescription
OnGreenThere is XCC WLAN connection.
OffNoneThe is no XCC WLAN connection, or the server does not come with wireless module.

3 9 Security LED (green)​

The states of security LED are as following:
  • Solid on: The server is operating with security feature enabled.
  • Blinking: The server is in System Lockdown Mode. Activate or unlock the system for operation. See Activate or unlock the system.
  • Off: No security feature is enabled on the server.

4 8 System Error LED (yellow)​

The system error LED helps you to determine if there are any system errors.

StatusColorDescriptionAction
OnYellow
An error has been detected on the server. Causes might include one or more of the following errors:

  • The temperature of the server reached the non-critical temperature threshold.

  • The voltage of the server reached the non-critical voltage threshold.

  • A fan has been detected to be running at low speed.

  • The power supply has a critical error.

  • The power supply is not connected to the power.

Check the Event log to determine the exact cause of the error.

OffNoneThe server is off or the server is on and is working correctly.None.

5 Bluetooth LED (blue) 14 Bluetooth button with LED (blue)​

Press the Bluetooth button to enable Bluetooth. After the Bluetooth button is pressed, if SE360 V2 does not pair with any Bluetooth devices within 10 minutes, Bluetooth will be disabled automatically. Identify the status of Bluetooth with the Bluetooth LED.

StatusColorDescription
OnBlueBluetooth is enabled.
OffNoneBluetooth is disabled, or the server does not come with Bluetooth.

6 System ID LED (blue) 13 System ID button with system ID LED (blue)​

Use the system ID button and the blue system ID LED to visually locate the server. Each time you press the system ID button, the state of the system ID LED changes. The LED can be changed to on, blinking, or off. You can also use the Lenovo XClarity Controller or a remote management program to change the state of the system ID LED to assist in visually locating the server among other servers.

7 Power status LED (green) 12 Power button with power status LED (green)​

You can press the power button to power on the server when you finish setting up the server. You also can hold the power button for several seconds to power off the server if you cannot shut down the server from the operating system. The states of the power LED are as follows:

StatusColorDescription
OffNoneNo power supply is properly installed, or the LED itself has failed.
Flashing rapidly (four times per second)GreenThe server is turned off and is not ready to be turned on. The power button is disabled. This will last approximately 5 to 10 seconds.
Flashing slowly (once per second)GreenThe server is turned off and is ready to be turned on. You can press the power button to turn on the server.
LitGreenThe server is turned on.