UEFI events organized by severity
The following table lists all UEFI events, organized by severity (Information, Error, and Warning).
| Event ID | Message String | Severity |
|---|---|---|
| FQXSFIO0005I | An intra-board UPI has been disabled on the link between processor [arg1] port [arg2] and processor [arg3]port [arg4] because of UPI topology downgrade. | Informational |
| FQXSFIO0006I | An inter-board UPI has been disabled on the link between processor [arg1] port [arg2] and processor [arg3]port [arg4] because of UPI topology downgrade. | Informational |
| FQXSFIO0021I | PCIe DPC software triggering occurred in physical [arg1] number [arg2]. | Informational |
| FQXSFMA0001I | DIMM [arg1] Disable has been recovered. [arg2] | Informational |
| FQXSFMA0002I | The uncorrectable memory error state has been cleared. | Informational |
| FQXSFMA0006I | [arg1] DIMM [arg2] has been detected, the DIMM serial number is [arg3]. | Informational |
| FQXSFMA0008I | DIMM [arg1] POST memory test failure has been recovered. [arg2] | Informational |
| FQXSFMA0009I | Invalid memory configuration for Mirror Mode has been recovered. | Informational |
| FQXSFMA0026I | DIMM [arg1] Self-healing, attempt post package repair (PPR) succeeded. [arg2] | Informational |
| FQXSFMA0027I | Invalid memory configuration (unsupported DIMM Population) recovered. | Informational |
| FQXSFMA0029I | The PFA of DIMM [arg1] has been deasserted after applying PPR for this DIMM. [arg2] | Informational |
| FQXSFMA0052I | DIMM [arg1] has been disabled due to the error on DIMM [arg2].[arg3] | Informational |
| FQXSFMA0053I | DIMM [arg1] re-enabled due to memory module combination updating. | Informational |
| FQXSFMA0056I | Uncorrected memory error occurred on DIMM [arg1] has been deasserted after performing post package repair. DIMM identifier is [arg2]. | Informational |
| FQXSFMA0063I | A correctable memory error handled by ADDDC on DIMM [arg1]. DIMM identifier is [arg2]. | Informational |
| FQXSFMA0065I | Multi-bit CE of DIMM [arg1] has been deasserted after performing post package repair. DIMM identifier is [arg2]. | Informational |
| FQXSFMA0067I | Errors per row counter threshold limit exceeded on DIMM [arg1] has been deasserted after performing post package repair. DIMM identifier is [arg2]. | Informational |
| FQXSFMA0079I | NVRAM [arg1] corruption detected and recovered. | Informational |
| FQXSFPU4034I | TPM Firmware recovery is finished, rebooting system to take effect. | Informational |
| FQXSFPU4038I | TPM Firmware recovery successful. | Informational |
| FQXSFPU4041I | TPM Firmware update is in progress. Please DO NOT power off or reset system. | Informational |
| FQXSFPU4042I | TPM Firmware update is finished, rebooting system to take effect. | Informational |
| FQXSFPU4044I | The current TPM firmware version could not support TPM version toggling. | Informational |
| FQXSFPU4059I | User requested to skip freezing lock of AHCI-attached SATA drives. System UEFI accepted the request and will execute prior to OS boot. | Informational |
| FQXSFPU4060I | Skipped freezing lock of AHCI-attached SATA drives. | Informational |
| FQXSFPU4061I | Restored default locking behavior of AHCI-attached SATA drives. | Informational |
| FQXSFPU4062I | CPU debugging is deactivated. | Informational |
| FQXSFPU4080I | Host Power-On password has been changed. | Informational |
| FQXSFPU4081I | Host Power-On password has been cleared. | Informational |
| FQXSFPU4082I | Host Admin password has been changed. | Informational |
| FQXSFPU4083I | Host Admin password has been cleared. | Informational |
| FQXSFSR0002I | [arg1] GPT corruption recovered, DiskGUID: [arg2] | Informational |
| FQXSFSR0003I | Boot OS successfully. | Informational |
| FQXSFIO0008M | An intra-board UPI dynamic link width reduction has been detected on the link between processor [arg1] port [arg2] and processor [arg3] port [arg4]. | Warning |
| FQXSFIO0009M | An inter-board UPI dynamic link width reduction has been detected on the link between processor [arg1] port [arg2] and processor [arg3] port [arg4]. | Warning |
| FQXSFIO0021J | PCIe Error Recovery has occurred in physical [arg1] number [arg2]. The [arg3] may not operate correctly. | Warning |
| FQXSFIO0022J | PCIe Link Width has degraded from [arg1] to [arg2] in physical [arg3] number [arg4]. | Warning |
| FQXSFIO0023J | PCIe Link Speed has degraded from [arg1] to [arg2] in physical [arg3] number [arg4]. | Warning |
| FQXSFIO0024I | An error has been detected by the IEH on processor [arg1]. The type of IEH is [arg2]. The index of the IEH is [arg3]. The value of IehErrorStatus register is [arg4]. Please check error logs for additional downstream device error data. | Warning |
| FQXSFIO0025I | An error has been detected by the IIO on processor [arg1]. The index of the IIO stack is [arg2]. The type of IIO Internal Error is [arg3]. Please check error logs for additional downstream device error data. | Warning |
| FQXSFIO0036G | PCIe Correctable Error Threshold limit has been exceeded at Segment 0x[arg1] Bus 0x[arg2] Device 0x[arg3] Function 0x[arg4]. The Vendor ID for the device is 0x[arg5] and the Device ID is 0x[arg6]. The physical [arg7] number is [arg8]. | Warning |
| FQXSFIO0041J | PCIe Leaky Bucket Event : [arg1] occurred at Segment [arg2] Bus [arg3] Device [arg4] Function [arg5]. The physical [arg6] number is [arg7]. | Warning |
| FQXSFMA0026G | Multi-bit CE occurred on DIMM [arg1], need to restart the system for DIMM Self-healing to attempt post package repair (PPR).[arg2] | Warning |
| FQXSFMA0027G | Multi-bit CE occurred on DIMM [arg1] different rows.[arg2] | Warning |
| FQXSFMA0027M | DIMM [arg1] Self-healing, attempt post package repair (PPR) failed. [arg2] | Warning |
| FQXSFMA0028M | DIMM [arg1] Self-healing, attempt post package repair (PPR) exceeded DIMM level threshold. [arg2] | Warning |
| FQXSFMA0029G | DIMM [arg1] Self-healing, attempt post package repair (PPR) failed: Insufficient rows available for repair. [arg2] | Warning |
| FQXSFMA0047M | SPD CRC checking failed on DIMM [arg1]. [arg2] | Warning |
| FQXSFMA0048M | DIMM [arg1] disabled due to PMIC failure during POST, DIMM identifier is [arg2]. | Warning |
| FQXSFMA0049M | DIMM [arg1] disabled due to memory module power failure. DIMM [arg2] detected and good, DIMM [arg3] not detected. | Warning |
| FQXSFMA0050G | DRAM PFA threshold limit exceeded on DIMM [arg1] sub-channel [arg2] Rank [arg3] DRAM [arg4], DIMM identifier is [arg5]. | Warning |
| FQXSFMA0053G | An uncorrected memory error has been recovered by mirror on DIMM [arg1] at address [arg2].[arg3] | Warning |
| FQXSFMA0053M | DIMM [arg1] not defective but disabled due to unsupported memory module combination on CPU [arg2]. | Warning |
| FQXSFMA0054G | Mirror failover operation was successful. DIMM [arg1] has failed over to the mirrored DIMM [arg2].[arg3] | Warning |
| FQXSFMA0055G | Mirror failover operation is skipped and page retire for uncorrectable error (at [arg1]) on DIMM [arg2] is reported to OS. [arg3] | Warning |
| FQXSFMA0057G | Page Retire PFA Threshold limit exceeded on DIMM [arg1] at address [arg2].[arg3] [arg4] | Warning |
| FQXSFMA0064M | DIMM [arg1] disabled due to memory module power failure. DIMM [arg2] detected and good. | Warning |
| FQXSFMA0067G | Errors per row counter threshold limit exceeded on DIMM [arg1] sub-channel [arg2] Rank [arg3] DRAM [arg4], need to restart the system for DIMM Self-healing to attempt post package repair (PPR), DIMM identifier is [arg5]. | Warning |
| FQXSFMA0076M | DIMM [arg1] is not supported, DIMM identifier is [arg2]. | Warning |
| FQXSFPU0023G | Secure Boot Image Verification Failure Warning. | Warning |
| FQXSFPU0039G | 3rd party option rom of PCIe physical [arg1] number [arg2] failed secure boot verification. | Warning |
| FQXSFPU0040G | Secure boot keys were reset to factory default. | Warning |
| FQXSFPU0062F | System uncorrected recoverable error happened in Processor [arg1] Core [arg2] MC bank [arg3] with MC Status [arg4], MC Address [arg5], and MC Misc [arg6]. | Warning |
| FQXSFPU4033F | TPM Firmware recovery is in progress. Please DO NOT power off or reset system. | Warning |
| FQXSFPU4035M | TPM Firmware recovery failed. TPM chip may be damaged. | Warning |
| FQXSFPU4040M | TPM selftest has failed. | Warning |
| FQXSFPU4050G | Failed to update TPM Firmware. | Warning |
| FQXSFPU4051G | Undefined TPM_POLICY found. | Warning |
| FQXSFPU4052G | TPM_POLICY is not locked. | Warning |
| FQXSFPU4053G | System TPM_POLICY does not match the planar. | Warning |
| FQXSFPU4062M | CPU debugging is activated. | Warning |
| FQXSFSR0001M | [arg1] GPT corruption detected, DiskGUID: [arg2] | Warning |
| FQXSFSR0003G | The number of boot attempts has been exceeded. No bootable device found. | Warning |
| FQXSFIO0005M | An intra-board UPI failure has been detected on the link between processor [arg1] port [arg2] and processor [arg3] port [arg4]. | Error |
| FQXSFIO0006M | An inter-board UPI failure has been detected on the link between processor [arg1] port [arg2] and processor [arg3] port [arg4]. | Error |
| FQXSFIO0013M | New added PCI device(s) at [arg1] triggered [arg2] out of resource. | Error |
| FQXSFIO0024M | An error has been detected by the IEH on processor [arg1]. The type of IEH is [arg2]. The index of the IEH is [arg3]. The value of IehErrorStatus register is [arg4]. Please check error logs for additional downstream device error data. | Error |
| FQXSFIO0025M | An error has been detected by the IIO on processor [arg1]. The index of the IIO stack is [arg2]. The type of IIO Internal Error is [arg3]. Please check error logs for additional downstream device error data. | Error |
| FQXSFIO0035M | An Uncorrectable PCIe Error has Occurred at Segment 0x[arg1] Bus 0x[arg2] Device 0x[arg3] Function 0x[arg4]. The Vendor ID for the device is 0x[arg5] and the Device ID is 0x[arg6]. The physical [arg7] number is [arg8]. | Error |
| FQXSFMA0001M | DIMM [arg1] has been disabled due to an error detected during POST. [arg2] | Error |
| FQXSFMA0002M | An uncorrectable memory error has been detected on DIMM [arg1] at address [arg2]. [arg3] | Error |
| FQXSFMA0004N | No system memory has been detected. | Error |
| FQXSFMA0008M | DIMM [arg1] has failed the POST memory test. [arg2] | Error |
| FQXSFMA0009K | Invalid memory configuration for Mirror Mode. Please correct memory configuration. | Error |
| FQXSFMA0027K | Invalid memory configuration (Unsupported DIMM Population) detected. Please verify memory configuration is valid. | Error |
| FQXSFMA0056M | An uncorrected recoverable memory error has been detected on DIMM [arg1] at address [arg2].[arg3] [arg4] | Error |
| FQXSFMA0066M | Memory address parity error occurred on CPU [arg1] channel [arg2] with DIMM [arg3]. | Error |
| FQXSFMA0077N | SMBus failure encountered when accessing to the SPD of DIMM [arg1]. | Error |
| FQXSFMA0078N | System encountered fatal error [arg1] during memory initialization. | Error |
| FQXSFMA0082M | An uncorrected recoverable memory error has been detected on DIMM [arg1] and post package repair (PPR) recorded. | Error |
| FQXSFMA0083M | An uncorrected recoverable memory error has been detected on DIMM [arg1] and post package repair (PPR) recording failed. | Error |
| FQXSFPU0016N | A processor within the system has failed the BIST. | Error |
| FQXSFPU0018N | CATERR(IERR) has asserted on processor [arg1]. | Error |
| FQXSFPU0019N | An uncorrectable error has been detected on processor [arg1]. | Error |
| FQXSFPU0027N | System uncorrectable error has occurred on Processor [arg1] Core [arg2] MC bank [arg3] with MC Status [arg4], MC Address [arg5], and MC Misc [arg6]. | Error |
| FQXSFPU0030N | A firmware fault has been detected in the UEFI image. | Error |
| FQXSFPU0035N | A 3-strike timeout has occurred on processor [arg1]. | Error |
| FQXSFPU4056M | TPM card is changed, need install back the original TPM card which shipped with the system. | Error |
| FQXSFSM0008M | Boot permission timeout detected. | Error |
Give documentation feedback