Rear view

• Rear view with eight PCIe slots

• Rear view with ten PCIe slots

• Rear view with four 2.5-inch rear drive bays and six PCIe slots

• Rear view with eight 2.5-inch rear drive bays and four PCIe slots

• Rear view with two 3.5-inch rear drive bays and four PCIe slots

• Rear view with four 3.5-inch rear drive bays and two PCIe slots

• Rear view with seven PCIe slots and a DWCM

• Rear view with nine PCIe slots and a DWCM

• Rear view with four 2.5-inch rear drive bays, five PCIe slots, and a DWCM

• Rear view with eight 2.5-inch rear drive bays, three PCIe slots, and a DWCM

• Rear view with two 3.5-inch rear drive bays, three PCIe slots, and a DWCM

• Rear view with four 3.5-inch rear drive bays, one PCIe slot, and a DWCM

Rear view with eight PCIe slots​

Rear view with ten PCIe slots​

Rear view with four 2.5-inch rear drive bays and six PCIe slots​

Rear view with eight 2.5-inch rear drive bays and four PCIe slots​

Rear view with two 3.5-inch rear drive bays and four PCIe slots​

Rear view with four 3.5-inch rear drive bays and two PCIe slots​

Rear view with seven PCIe slots and a DWCM​

Rear view with nine PCIe slots and a DWCM​

Rear view with four 2.5-inch rear drive bays, five PCIe slots, and a DWCM​

Rear view with eight 2.5-inch rear drive bays, three PCIe slots, and a DWCM​

Rear view with two 3.5-inch rear drive bays, three PCIe slots, and a DWCM​

Rear view with four 3.5-inch rear drive bays, one PCIe slot, and a DWCM​

Rear components overview​

PCIe slots​

The PCIe slots are on the rear or front of the server, and your server supports up to 12 PCIe slots. For more information, see PCIe slots and PCIe adapters.

Hot-swap drives and drive bays​

The drive bays on the front and rear of your server are designed for hot-swap drives. The number of the installed drives in your server varies by model. When you install drives, follow the order of the drive bay numbers.

The EMI integrity and cooling of the server are protected by having all drive bays occupied. Vacant drive bays must be occupied by drive fillers.

Power supplies​

The hot-swap redundant power supply helps you avoid significant interruption to the operation of the system when a power supply fails. You can purchase a power supply option from Lenovo and install the power supply to provide power redundancy without turning off the server.

On each power supply, there are three status LEDs near the power cord connector. For information about the LEDs, see Power supply LEDs.

NMI button​

Use this button only when you are directed to do so by Lenovo Support. Press this button to force a nonmaskable interrupt (NMI) to the processor. By this way, you can make the operating system halt (such as Windows Blue Screen of Death) and take a memory dump. You might have to use a pen or the end of a straightened paper clip to press the button.

USB 3 (5 Gbps) connectors​

The USB 3.2 Gen 1 (5 Gbps) connectors are direct connect interfaces (DCIs) for debugging, which can be used to attach a USB-compatible device, such as a USB keyboard, USB mouse, or USB storage device.

VGA connector​

The VGA connectors on the front and rear of the server can be used to attach a high-performance monitor, a direct-drive monitor, or other devices that use a VGA connector.

XCC system management port​

The server has a 1 Gb RJ-45 connector dedicated to Lenovo XClarity Controller (XCC) functions. Through the system management port, you can access the Lenovo XClarity Controller directly by connecting your laptop to the management port using an Ethernet cable. Make sure that you modify the IP settings on the laptop so that it is on the same network as the server default settings. A dedicated management network provides additional security by physically separating the management network traffic from the production network.

Ethernet connectors​

Figure 1. OCP module (two connectors)

Figure 2. OCP module (four connectors)

The OCP module provides two or four extra Ethernet connectors for network connections.

By default, one of the Ethernet connectors on the OCP module can also function as a management connector using the shared management capacity.

Inlet and outlet hoses​

The Direct Water Cooling Module (DWCM) spreads two hoses out to connect to the manifolds. The inlet hose conveys warm water from the facility to the cold plates to cool down the processors, and the outlet hose conducts hot water out of the DWCM to realize system cooling.