Parts list
Use the parts list to identify each of the components that are available for your server.
For more information about ordering the parts shown in Figure 1:
Tier 1 customer replaceable unit (CRU): Replacement of Tier 1 CRUs is your responsibility. If Lenovo installs a Tier 1 CRU at your request with no service agreement, you will be charged for the installation.
Tier 2 customer replaceable unit (CRU): You may install a Tier 2 CRU yourself or request Lenovo to install it, at no additional charge, under the type of warranty service that is designated for your server.
Field replaceable unit (FRU): FRUs must be installed only by trained service technicians.
Consumable and Structural parts: Purchase and replacement of consumable and structural parts is your responsibility. If Lenovo acquires or installs a structural component at your request, you will be charged for the service.
Index | Description | Tier 1 CRU | Tier 2 CRU | FRU | Consumable and Structural parts |
---|---|---|---|---|---|
For more information about ordering the parts shown in Figure 1: It is highly recommended that you check the power summary data for your server using Lenovo Capacity Planner before purchasing any new parts. | |||||
1 | Top cover | √ | |||
2 | RAID adapter | √ | |||
3 | LOM-adapter air baffle | √ | |||
4 | LOM adapter | √ | |||
5 | Memory module (DCPMM might look slightly different from the illustration) | √ | |||
6 | Heat sink | √ | |||
7 | Processor | √ | |||
8 | TCM/TPM adapter (for Chinese Mainland only) | √ | |||
9 | System board | √ | |||
10 | P4 GPU air baffle | √ | |||
11 | FHHL V100 GPU air baffle | √ | |||
12 | Fan | √ | |||
13 | Fan cage | √ | |||
14 | RAID super capacitor module | √ | |||
15 | Standard air baffle | √ | |||
16 | Serial port module | √ | |||
17 | Backplane, eight 2.5-inch hot-swap drives | √ | |||
18 | Backplane, twelve 3.5-inch hot-swap drives | √ | |||
19 | Backplane, eight 3.5-inch hot-swap drives | √ | |||
20 | Right rack latch, with front I/O assembly | √ | |||
21 | Left rack latch, with VGA connector | √ | |||
22 | Right rack latch, without front I/O assembly | √ | |||
23 | Left rack latch, without VGA connector | √ | |||
24 | Chassis | √ | |||
25 | Security bezel | √ | |||
26 | Front I/O assembly, server models with eight 3.5-inch drive bays | √ | |||
27 | Front I/O assembly, server models with eight or sixteen 2.5-inch drive bays | √ | |||
28 | Filler, 3.5-inch drive | √ | |||
29 | Storage drive, 3.5-inch, hot-swap | √ | |||
30 | Filler, 2.5-inch drive | √ | |||
31 | Storage drive, 2.5-inch, hot-swap | √ | |||
32 | Large-size air baffle | √ | |||
33 | Riser 2 bracket | √ | |||
34 | Riser card | √ | |||
35 | Riser 1 bracket | √ | |||
36 | PCIe adapter | √ | |||
37 | Rear hot-swap drive assembly | √ | |||
38 | Power supply | √ | |||
39 | CMOS battery (CR2032) | √ | |||
40 | M.2 drive | √ | |||
41 | M.2 retainer | √ | |||
42 | M.2 backplane | √ | |||
43 | 480 GB M.2 drive air baffle | √ |