Skip to main content

Install the H100/H200 GPU baseboard

Follow instructions in this section to install the H100/H200 GPU baseboard. The procedure must be executed by a trained technician.

About this task

Attention
  • Read Installation Guidelines and Safety inspection checklist to ensure that you work safely.
  • Touch the static-protective package that contains the component to any unpainted metal surface on the server; then, remove it from the package and place it on a static-protective surface.
  • Two people and one lifting device on site that can support up to 400 lb (181 kg) are required to perform this procedure. If you do not already have a lifting device available, Lenovo offers the Genie Lift GL-8 material lift that can be purchased at Data Center Solution Configurator. Make sure to include the Foot-release brake and the Load Platform when ordering the Genie Lift GL-8 material lift.
  • Make sure to inspect the connectors and sockets on the GPU and the GPU baseboard. Do not use the GPU or the GPU baseboard if its connectors are damaged or missing, or if there are debris in the sockets. Replace the GPU or the GPU baseboard with a new one before continuing the installation procedure.
Note
Make sure you have the required tools listed below available to properly replace the component:
  • Torque screwdriver which can be set to 0.6 newton-meters, 5.3 inch-pounds
  • Torx T15 extended bit (6-inch long)
Firmware and driver download: You might need to update the firmware or driver after replacing a component.

Procedure

  1. (Optional) Remove the new GPU baseboard from the package box.
    1. Extend the two handles on both sides of the GPU baseboard.
    2. Hold the two handles, and remove the GPU baseboard out from the package box.
    Figure 1. Removing the GPU baseboard from the package box
    Removing the GPU baseboard from the package box
  2. Install the GPU baseboard.
    1. Hold the handles (1) on both sides of the GPU baseboard in the correct orientation as illustrated; then, align the GPU baseboard with the seventeen standoffs on the GPU complex adapter plate, and gently place it onto the adapter plate.
    2. Push the two handles (1) down.
    Figure 2. GPU baseboard installation
    GPU baseboard installation
  3. Follow the sequence shown in the illustration below to fasten the seventeen Torx T15 captive screws to secure the GPU baseboard.
    Important
    Do not overtighten the screws to avoid damage.
    Note
    Loosen or tighten the screws with a torque screwdriver set to the proper torque. For reference, the torque required for the screws to be fully loosen or tighten is 0.6 newton-meters, 5.3 inch-pounds.
    Figure 3. Screw installation
    Screw installation
  4. Flip over the front PCIe switch cable harness.
    1. Flip over the front PCIe switch cable harness, and make sure that it correctly engages the four guide pins on the 8U GPU shuttle.
    2. Locate the ten screw holes marked with C on both sides of the 8U GPU shuttle; then, fasten the ten screws to secure the front PCIe switch cable harness.
    Figure 4. Flipping over the front PCIe switch cable harness
    Flipping over the front PCIe switch cable harness
  5. Install the PCIe switch shuttle.
    1. Press the two blue release latches.
    2. Press the two lock latches on both sides of the PCIe switch shuttle.
    3. Push the PCIe switch shuttle into the 8U GPU shuttle until it stops.
    4. Rotate the two release levers until they lock into place.
      Figure 5. PCIe switch shuttle installation to 8U GPU shuttle
      PCIe switch shuttle installation to 8U GPU shuttle

After you finish

  1. Reinstall all the GPU and heat sink modules. See Install an H100/H200 GPU and heat sink module.
  2. Reconnect the cables to the GPU baseboard. See GPU baseboard cable routing for more information.
  3. Reinstall all the GPU air ducts. See Install an H100/H200 GPU air duct.
  4. Reinstall all the rear fan control board assemblies. See Install a rear fan control board assembly.
  5. If necessary, reinstall the rear support bracket.
    1. Hold the rear support bracket in the correct orientation as illustrated, and slide it into the 8U GPU shuttle.
    2. Locate the four screw holes marked with A on both sides of the 8U GPU shuttle; then, fasten the four screws to secure the rear support bracket.
    Figure 6. Rear support bracket installation
    Rear support bracket installation
  6. Reinstall the power complex. See Install the power complex.
  7. Reinstall the cable cover. See Install the cable cover.
  8. Reinstall the 8U GPU shuttle. See Install the 8U GPU shuttle.
  9. Reinstall all the 2.5-inch hot-swap drives or drive bay fillers (if any) into the drive bays. See Install a 2.5-inch hot-swap drive
  10. Reinstall all the front fans. See Install a hot-swap fan (front and rear).
  11. Reinstall all the power supply units. See Install a hot-swap power supply unit.
  12. Complete the parts replacement. See Complete the parts replacement.