Skip to main content

Storage drive problems

Use this information to resolve issues related to the storage drives.

Server cannot recognize a drive​

Complete the following steps until the problem is solved.

  1. Observe the associated yellow drive status LED. If the LED is lit, it indicates a drive fault.

  2. If the status LED is lit, remove the drive from the bay, wait 45 seconds, and reinsert the drive, making sure that the drive assembly connects to the drive backplane.

  3. Observe the associated green drive activity LED and the yellow status LED and perform corresponding operations in different situations:

    • If the green activity LED is flashing and the yellow status LED is not lit, the drive is recognized by the controller and is working correctly. Run the diagnostics tests for the drives. When you start a server and press the key according to the on-screen instructions, the LXPM is displayed by default. (For more information, see the “Startup” section in the LXPM documentation compatible with your server at Lenovo XClarity Provisioning Manager portal page.) You can perform drive diagnostics from this interface. From the Diagnostic page, click Run Diagnostic > Disk Drive Test.

    • If the green activity LED is flashing and the yellow status LED is flashing slowly, the drive is recognized by the controller and is rebuilding.

    • If neither LED is lit or flashing, check whether the drive backplane is correctly seated. For details, go to step 4.

    • If the green activity LED is flashing and the yellow status LED is lit, replace the drive.

  4. Make sure that the drive backplane is correctly seated. When it is correctly seated, the drive assemblies correctly connect to the backplane without bowing or causing movement of the backplane.

  5. Reseat the backplane power cable and repeat steps 1 through 3.

  6. Reseat the backplane signal cable and repeat steps 1 through 3.

  7. Suspect the backplane signal cable or the backplane:

    • Replace the affected backplane signal cable.

    • Replace the affected backplane.

  8. Run the diagnostics tests for the drives. When you start a server and press the key according to the on-screen instructions, the LXPM is displayed by default. (For more information, see the “Startup” section in the LXPM documentation compatible with your server at Lenovo XClarity Provisioning Manager portal page.) You can perform drive diagnostics from this interface. From the Diagnostic page, click Run Diagnostic > Disk Drive Test.

    Based on those tests:

    • If the backplane passes the test but the drives are not recognized, replace the backplane signal cable and run the tests again.

    • Replace the backplane.

    • If the adapter fails the test, disconnect the backplane signal cable from the adapter and run the tests again.

    • If the adapter fails the test, replace the adapter.

Multiple drives fail​

Complete the following steps until the problem is solved:

  • View the Lenovo XClarity Controller event log for events related to power supplies or vibration issues and resolve those events.

  • Make sure that the device drivers and firmware for the drive and server are at the latest level.

Important
Some cluster solutions require specific code levels or coordinated code updates. If the device is part of a cluster solution, verify that the latest level of code is supported for the cluster solution before you update the code.

Multiple drives are offline​

Complete the following steps until the problem is solved:

  • View the Lenovo XClarity Controller event log for events related to power supplies or vibration issues and resolve those events.

  • View the storage subsystem log for events related to the storage subsystem and resolve those events.

A replacement drive does not rebuild​

Complete the following steps until the problem is solved:

  1. Make sure that the drive is recognized by the adapter (the green drive activity LED is flashing).

  2. Review the SAS/SATA RAID adapter documentation to determine the correct configuration parameters and settings.

Green drive activity LED does not represent actual state of associated drive​

Complete the following steps until the problem is solved:

  1. If the green drive activity LED does not flash when the drive is in use, run the diagnostics tests for the drives. When you start a server and press the key according to the on-screen instructions, the LXPM is displayed by default. (For more information, see the “Startup” section in the LXPM documentation compatible with your server at Lenovo XClarity Provisioning Manager portal page.) You can perform drive diagnostics from this interface. From the Diagnostic page, click Run Diagnostic > Disk Drive Test

  2. If the drive passes the test, replace the backplane.

  3. If the drive fails the test, replace the drive.