Skip to main content

XCC events organized by severity

The following table lists all XCC events, organized by severity (Information, Error, and Warning).

Table 1. Events organized by severity
Event IDMessage StringSeverity
FQXSPBR4000IManagement Controller [arg1]: Configuration restored from a file by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPBR4002IManagement Controller [arg1] Reset was caused by restoring default values.Informational
FQXSPBR4004IServer timeouts set by user [arg1]: EnableOSWatchdog=[arg2], OSWatchdogTimout=[arg3], EnableLoaderWatchdog=[arg4], LoaderTimeout=[arg5].Informational
FQXSPBR4005IManagement Controller [arg1]: Configuration saved to a file by user [arg2].Informational
FQXSPBR4006IManagement Controller [arg1]: Configuration restoration from a file by user [arg2] completed from [arg3] at IP address [arg4].Informational
FQXSPBR4009IManagement Controller [arg1]: cloning configuration from neighbor server [arg2] by group name [arg3].Informational
FQXSPBR400AIManagement Controller [arg1]: cloning configuration from neighbor server [arg2] by group name [arg3] completed.Informational
FQXSPBR400BIManagement Controller [arg1]: cloning configuration from neighbor server [arg2] by group name [arg3] failed to complete.Informational
FQXSPBR400CIManagement Controller [arg1]: cloning configuration from neighbor server [arg2] by group name [arg3] failed to start.Informational
FQXSPBR400DINeighbor group clone configuration was initiated by user [arg1].Informational
FQXSPBR400EINeighbor group firmware update was initiated by user [arg1].Informational
FQXSPBR400FIThe neighbor group management is [arg1] by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPBT0007INo bootable media available for system [ComputerSystemElementName].Informational
FQXSPCA2007INumeric sensor [NumericSensorElementName] going high (upper non-critical) has deasserted.Informational
FQXSPCA2009INumeric sensor [NumericSensorElementName] going high (upper critical) has deasserted.Informational
FQXSPCA2011INumeric sensor [NumericSensorElementName] going high (upper non-recoverable) has deasserted.Informational
FQXSPCA2015ISensor [SensorElementName] has deasserted the transition from normal to non-critical state.Informational
FQXSPCA2017ISensor [SensorElementName] has transitioned to a less severe state from critical.Informational
FQXSPCA2019ISensor [SensorElementName] has deasserted the transition to non-recoverable from a less severe state.Informational
FQXSPCN4000ISerial Redirection set by user [arg1]: Mode=[arg2], BaudRate=[arg3], StopBits=[arg4], Parity=[arg5], SessionTerminateSequence=[arg6].Informational
FQXSPCN4001IRemote Control session started by user [arg1] in [arg2] mode.Informational
FQXSPCN4002IUser [arg1] has terminated an active CLI console session.Informational
FQXSPCN4003IRemote Control session started by user [arg1] in [arg2] mode has been closed.Informational
FQXSPCN4004IUser [arg1] has created an active [arg2] console session.Informational
FQXSPCN4005IA [arg1] console session is timeout.Informational
FQXSPCN4006IUser [arg1] has terminated an active IPMI console session.Informational
FQXSPDM4000IInventory data changed for device [arg1], new device data hash=[arg2], new master data hash=[arg3] .Informational
FQXSPDM4001IStorage [arg1] has changed.Informational
FQXSPDM4003ITKLM servers set by user [arg1]: TKLMServer1=[arg2] Port=[arg3], TKLMServer2=[arg4] Port=[arg5], TKLMServer3=[arg6] Port=[arg7], TKLMServer4=[arg8] Port=[arg9].Informational
FQXSPDM4004ITKLM servers device group set by user [arg1]: TKLMServerDeviceGroup=[arg2] .Informational
FQXSPDM4005IUser [arg1] has generated a new encryption key pair and installed a self-signed certificate for the TKLM client.Informational
FQXSPDM4006IUser [arg1] has generated a new encryption key and certificate signing request for the TKLM client.Informational
FQXSPDM4007IUser [arg1] has imported a signed certificate for the TKLM client from [arg2].Informational
FQXSPDM4008IUser [arg1] has imported a server certificate for the TKLM server.Informational
FQXSPDM4009IUser [arg1] has [arg2] file [arg3] from [arg4].Informational
FQXSPDM4010IInventory data collecting and processing complete for [arg1], sequence number is [arg2].Informational
FQXSPDM4011IEKMS server protocol set by user [arg1]: TKLMServerProtocol=[arg2] .Informational
FQXSPDM4012IUser [arg1] has changed the polling configuration for the key management server.: Polling enabled=[arg2] Interval=[arg3]Informational
FQXSPDM4013IUser [arg1] has changed the caching configuration for the key management server: Caching enabled=[arg2] Interval=[arg3]Informational
FQXSPEM0003IThe Log [RecordLogElementName] has been cleared.Informational
FQXSPEM0004IThe Log [RecordLogElementName] is full.Informational
FQXSPEM0005IThe Log [RecordLogElementName] is almost full.Informational
FQXSPEM0009IThe System [ComputerSystemElementName] has generated an auxiliary Log Entry in Log [RecordLogElement].Informational
FQXSPEM4000IThe [arg1] on system [arg2] cleared by user [arg3].Informational
FQXSPEM4001IThe [arg1] on system [arg2] is 75% full.Informational
FQXSPEM4002IThe [arg1] on system [arg2] is 100% full.Informational
FQXSPEM4003ILED [arg1] state changed to [arg2] by [arg3].Informational
FQXSPEM4004ISNMP [arg1] enabled by user [arg2] .Informational
FQXSPEM4005ISNMP [arg1] disabled by user [arg2] .Informational
FQXSPEM4006IAlert Configuration Global Event Notification set by user [arg1]: RetryLimit=[arg2], RetryInterval=[arg3], EntryInterval=[arg4].Informational
FQXSPEM4007IAlert Recipient Number [arg1] updated: Name=[arg2], DeliveryMethod=[arg3], Address=[arg4], IncludeLog=[arg5], Enabled=[arg6], EnabledAlerts=[arg7], AllowedFilters=[arg8] by user [arg9] from [arg10] at IP address [arg11].Informational
FQXSPEM4008ISNMP Traps enabled by user [arg1]: EnabledAlerts=[arg2], AllowedFilters=[arg3] .Informational
FQXSPEM4009IThe UEFI Definitions have been changed.Informational
FQXSPEM4010IUEFI Reported: [arg1].Informational
FQXSPEM4011IXCC failed to log previous event [arg1].Informational
FQXSPEM4012IUser [arg1] made system [arg2] Encapsulation lite Mode.Informational
FQXSPEM4013IBattery error was detected by RAID controller. The battery unit needs replacement.([arg1],[arg2],[arg3],[arg4],[arg5])Informational
FQXSPEM4014IThe RAID controller has problem with the battery. Please contact technical support to resolve this issue.([arg1],[arg2],[arg3],[arg4],[arg5])Informational
FQXSPEM4015IThe RAID controller detected unrecoverable error. The controller needs replacement.([arg1],[arg2],[arg3],[arg4],[arg5])Informational
FQXSPEM4016IThe RAID controller detected one or more problems. Please contact technical support for additional assistance.([arg1],[arg2],[arg3],[arg4],[arg5])Informational
FQXSPEM4017IThe RAID controller detected one or more possible configuration changes within the subsystem. Please check the drive LED status. If necessary, contact technical support for additional assistance.([arg1],[arg2],[arg3],[arg4],[arg5])Informational
FQXSPEM4018IEnclosure/Chassis issue detected with one or more units. Please check the enclosure/chassis units to repair the problem.([arg1],[arg2],[arg3],[arg4],[arg5])Informational
FQXSPEM4019IConnectivity issue detected with the enclosure/chassis. Please check your cable configurations to repair the problem.([arg1],[arg2],[arg3],[arg4],[arg5])Informational
FQXSPEM4020IFan problem detected with the enclosure/chassis. Please check the enclosure/chassis unit fan for correct operation.([arg1],[arg2],[arg3],[arg4],[arg5])Informational
FQXSPEM4022IEnclosure/Chassis power supply has problem. Please check the enclosure/chassis unit power supply for correct operation.([arg1],[arg2],[arg3],[arg4],[arg5])Informational
FQXSPEM4023IOne or more virtual drive are in abnormal status that may cause unavailable virtual drive. Please check the event logs and if events are targeted to the same disk then replace the drive. If necessary, contact technical support for additional assistance.([arg1],[arg2],[arg3],[arg4],[arg5])Informational
FQXSPEM4024IThe RAID controller detected one or more possible configuration problem within the subsystem. Please check the event logs and if events are targeted to the same disk then replace the drive. If necessary, contact technical support for additional assistance.([arg1],[arg2],[arg3],[arg4],[arg5])Informational
FQXSPEM4025IOne or more virtual drive have problem. Please contact technical support to resolve this issue.([arg1],[arg2],[arg3],[arg4],[arg5])Informational
FQXSPEM4026IDrive error was detected by RAID controller. Please contact technical support to resolve this issue.([arg1],[arg2],[arg3],[arg4],[arg5])Informational
FQXSPEM4027IDrive error was detected by RAID controller. Please check the event logs and if events are targeted to the same disk then replace the drive. If necessary, contact technical support for additional assistance.([arg1],[arg2],[arg3],[arg4],[arg5])Informational
FQXSPEM4028IThe port [arg1] of PCIe device [arg2] at [arg3] has link [arg4].Informational
FQXSPEM4029IAll PCIe slots on [arg1] may not be functional based upon your current CPU population.Informational
FQXSPEM4030IA scheduled operation on the RAID controller has encountered an issue. Refer to RAID Logs under Server Management, Local Storage, for details.([arg1],[arg2],[arg3],[arg4],[arg5])Informational
FQXSPEM4031ISSD wear threshold setting is changed from [arg1] to [arg2] by user [arg3] from [arg4] at IP address [arg5].Informational
FQXSPEM4032IAcoustic Mode [arg1] has been engaged. Fan speed limits are in place.Informational
FQXSPEM4033IAcoustic Mode [arg1] has been disengaged to allow adequate cooling.Informational
FQXSPEM4036IDust filter measurement schedule is configured on server [arg1] by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPEM4037IAttempting to perform scheduled dust filter measurement on server [arg1].Informational
FQXSPEM4038IDust filter measurement schedule is disabled on server [arg1] by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPEM4039IAttempting to perform an immediate dust filter measurement on server [arg1] by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPEM4041IThe SmartNIC in slot [arg1] encountered boot timeout.Informational
FQXSPEM4042IThe SmartNIC in slot [arg1] went through a crash dump.Informational
FQXSPEM4044IDust filter measurement was successfully completed, no action is needed.Informational
FQXSPFC4000IThe bare metal connection process has been started.Informational
FQXSPFC4001IThe bare metal update application reports a status of [arg1].Informational
FQXSPFC4002ISystem running in setup.Informational
FQXSPFC4003IUEFI deployment boot mode is enabled for NextBoot.Informational
FQXSPFC4004IUEFI deployment boot mode is enabled for NextAc.Informational
FQXSPFC4005IUEFI deployment boot mode has been disabled.Informational
FQXSPFW0003IThe System [ComputerSystemElementName] encountered firmware progress.Informational
FQXSPFW2000IThe System [ComputerSystemElementName] has detected a POST Error deassertion.Informational
FQXSPFW2001IThe System [ComputerSystemElementName] has detected a POST Error deassertion.Informational
FQXSPFW2002IThe System [ComputerSystemElementName] has recovered from a firmware hang.Informational
FQXSPIO2003ISystem [ComputerSystemElementName] has recovered from a diagnostic interrupt.Informational
FQXSPIO2004IBus [SensorElementName] has recovered from a bus timeout.Informational
FQXSPIO2006ISystem [ComputerSystemElementName] has recovered from an NMI.Informational
FQXSPIO2010IBus [SensorElementName] has recovered from a Correctable Bus Error.Informational
FQXSPIO2011IBus [SensorElementName] has recovered from an Uncorrectable Error.Informational
FQXSPIO2013IBus [SensorElementName] has recovered from a Fatal Bus Error.Informational
FQXSPIO2015IFault condition removed on slot [PhysicalConnectorElementName] on system [ComputerSystemElementName].Informational
FQXSPIO4002IGPU Board Status was recovered by [arg1] of [arg1].Informational
FQXSPMA0004I[PhysicalMemoryElementName] Disabled on Subsystem [MemoryElementName].Informational
FQXSPMA2002IConfiguration error for [PhysicalMemoryElementName] on Subsystem [MemoryElementName] has deasserted.Informational
FQXSPMA2004I[PhysicalMemoryElementName] Enabled on Subsystem [MemoryElementName].Informational
FQXSPMA2005IThe System [ComputerSystemElementName] has detected a POST Error deassertion.Informational
FQXSPMA2007IScrub Failure for [PhysicalMemoryElementName] on Subsystem [MemoryElementName] has recovered.Informational
FQXSPMA2008IUncorrectable error recovery detected for [PhysicalMemoryElementName] on Subsystem [MemoryElementName].Informational
FQXSPMA2010I[PhysicalMemoryElementName] on Subsystem [MemoryElementName] is no longer Throttled.Informational
FQXSPMA2011IMemory Logging Limit Removed for [PhysicalMemoryElementName] on Subsystem [MemoryElementName].Informational
FQXSPMA2012IAn Over-Temperature Condition has been removed on the [PhysicalMemoryElementName] on Subsystem [MemoryElementName].Informational
FQXSPMA2013IThe System [ComputerSystemElementName] has detected a POST Error deassertion.Informational
FQXSPMA2015IRedundancy Lost for [RedundancySetElementName] has deasserted.Informational
FQXSPMA2017INon-redundant:Sufficient Resources from Redundancy Degraded or Fully Redundant for [RedundancySetElementName] has deasserted.Informational
FQXSPMA2019INon-redundant:Insufficient Resources for [RedundancySetElementName] has deasserted.Informational
FQXSPNM4000IManagement Controller [arg1] Network Initialization Complete.Informational
FQXSPNM4001IEthernet Data Rate modified from [arg1] to [arg2] by user [arg3].Informational
FQXSPNM4002IEthernet Duplex setting modified from [arg1] to [arg2] by user [arg3].Informational
FQXSPNM4003IEthernet MTU setting modified from [arg1] to [arg2] by user [arg3].Informational
FQXSPNM4004IEthernet locally administered MAC address modified from [arg1] to [arg2] by user [arg3].Informational
FQXSPNM4005IEthernet interface [arg1] by user [arg2].Informational
FQXSPNM4006IHostname set to [arg1] by user [arg2].Informational
FQXSPNM4007IIP address of network interface modified from [arg1] to [arg2] by user [arg3].Informational
FQXSPNM4008IIP subnet mask of network interface modified from [arg1] to [arg2] by user [arg3].Informational
FQXSPNM4009IIP address of default gateway modified from [arg1] to [arg2] by user [arg3].Informational
FQXSPNM4011IENET[[arg1]] DHCP-HSTN=[arg2], DN=[arg3], IP@=[arg4], SN=[arg5], GW@=[arg6], DNS1@=[arg7] .Informational
FQXSPNM4012IENET[[arg1]] IP-Cfg:HstName=[arg2], IP@=[arg3] ,NetMsk=[arg4], GW@=[arg5] .Informational
FQXSPNM4013ILAN: Ethernet[[arg1]] interface is no longer active.Informational
FQXSPNM4014ILAN: Ethernet[[arg1]] interface is now active.Informational
FQXSPNM4015IDHCP setting changed to [arg1] by user [arg2].Informational
FQXSPNM4016IDomain name set to [arg1] by user [arg2].Informational
FQXSPNM4017IDomain Source changed to [arg1] by user [arg2].Informational
FQXSPNM4018IDDNS setting changed to [arg1] by user [arg2].Informational
FQXSPNM4019IDDNS registration successful. The domain name is [arg1].Informational
FQXSPNM4020IIPv6 enabled by user [arg1] .Informational
FQXSPNM4021IIPv6 disabled by user [arg1] .Informational
FQXSPNM4022IIPv6 static IP configuration enabled by user [arg1].Informational
FQXSPNM4023IIPv6 DHCP enabled by user [arg1].Informational
FQXSPNM4024IIPv6 stateless auto-configuration enabled by user [arg1].Informational
FQXSPNM4025IIPv6 static IP configuration disabled by user [arg1].Informational
FQXSPNM4026IIPv6 DHCP disabled by user [arg1].Informational
FQXSPNM4027IIPv6 stateless auto-configuration disabled by user [arg1].Informational
FQXSPNM4028IENET[[arg1]] IPv6-LinkLocal:HstName=[arg2], IP@=[arg3] ,Pref=[arg4].Informational
FQXSPNM4029IENET[[arg1]] IPv6-Static:HstName=[arg2], IP@=[arg3] ,Pref=[arg4], GW@=[arg5] .Informational
FQXSPNM4030IENET[[arg1]] DHCPv6-HSTN=[arg2], DN=[arg3], IP@=[arg4], Pref=[arg5], DNS1@=[arg5].Informational
FQXSPNM4031IIPv6 static address of network interface modified from [arg1] to [arg2] by user [arg3].Informational
FQXSPNM4033ITelnet port number changed from [arg1] to [arg2] by user [arg3].Informational
FQXSPNM4034ISSH port number changed from [arg1] to [arg2] by user [arg3].Informational
FQXSPNM4035IWeb-HTTP port number changed from [arg1] to [arg2] by user [arg3].Informational
FQXSPNM4036IWeb-HTTPS port number changed from [arg1] to [arg2] by user [arg3].Informational
FQXSPNM4037ICIM/XML HTTP port number changed from [arg1] to [arg2] by user [arg3].Informational
FQXSPNM4038ICIM/XML HTTPS port number changed from [arg1] to [arg2] by user [arg3].Informational
FQXSPNM4039ISNMP Agent port number changed from [arg1] to [arg2] by user [arg3].Informational
FQXSPNM4040ISNMP Traps port number changed from [arg1] to [arg2] by user [arg3].Informational
FQXSPNM4041ISyslog port number changed from [arg1] to [arg2] by user [arg3].Informational
FQXSPNM4042IRemote Presence port number changed from [arg1] to [arg2] by user [arg3].Informational
FQXSPNM4043ISMTP Server set by user [arg1] to [arg2]:[arg3].Informational
FQXSPNM4044ITelnet [arg1] by user [arg2].Informational
FQXSPNM4045IDNS servers set by user [arg1]: UseAdditionalServers=[arg2], PreferredDNStype=[arg3], IPv4Server1=[arg4], IPv4Server2=[arg5], IPv4Server3=[arg6], IPv6Server1=[arg7], IPv6Server2=[arg8], IPv6Server3=[arg9].Informational
FQXSPNM4046ILAN over USB [arg1] by user [arg2].Informational
FQXSPNM4047ILAN over USB Port Forwarding set by user [arg1]: ExternalPort=[arg2], USB-LAN port=[arg3].Informational
FQXSPNM4048IPXE boot requested by user [arg1].Informational
FQXSPNM4049IUser [arg1] has initiated a TKLM Server Connection Test to check connectivity to server [arg2].Informational
FQXSPNM4050IUser [arg1] has initiated an SMTP Server Connection Test.Informational
FQXSPNM4051IUser [arg1] has set the SMTP Server reverse-path to [arg2].Informational
FQXSPNM4052IDHCP specified hostname is set to [arg1] by user [arg2].Informational
FQXSPNM4053IDNS discovery of Lenovo XClarity Administrator has been [arg1] by user [arg2].Informational
FQXSPNM4054IThe hostname from DHCP is [arg1] by user [arg2].Informational
FQXSPNM4055IThe hostname from DHCP is invalid.Informational
FQXSPNM4056IThe NTP server address [arg1] is invalid.Informational
FQXSPNM4057ISecurity: IP address: [arg1] had [arg2] login failures, it will be blocked to access for [arg3] minutes.Informational
FQXSPNM4058IIP address of network interface [arg1] is modified from [arg2] to [arg3] by user [arg4].Informational
FQXSPNM4059IIP subnet mask of network interface [arg1] is modified from [arg2] to [arg3] by user [arg4].Informational
FQXSPNM4060IIP address of default gateway of network interface [arg1] is modified from [arg2] to [arg3] by user [arg4].Informational
FQXSPOS4000IOS Watchdog response [arg1] by [arg2] .Informational
FQXSPOS4001IWatchdog [arg1] Screen Capture Occurred .Informational
FQXSPOS4004IOperating System status has changed to [arg1].Informational
FQXSPOS4005IHost Power-On password changed by user [arg1] from [arg2] at IP address [arg3].Informational
FQXSPOS4006IHost Power-On password cleared by user [arg1] from [arg2] at IP address [arg3].Informational
FQXSPOS4007IHost Admin password changed by user [arg1] from [arg2] at IP address [arg3].Informational
FQXSPOS4008IHost Admin password cleared by user [arg1] from [arg2] at IP address [arg3].Informational
FQXSPOS4009IOS Crash Video Captured.Informational
FQXSPOS4011IOS failure screen capture with hardware error is [arg1] by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPOS4012IPOST watchdog Screen Capture Occurred.Informational
FQXSPPP4000IAttempting to [arg1] server [arg2] by user [arg3].Informational
FQXSPPP4001IServer Power Off Delay set to [arg1] by user [arg2].Informational
FQXSPPP4002IServer [arg1] scheduled for [arg2] at [arg3] by user [arg4].Informational
FQXSPPP4003IServer [arg1] scheduled for every [arg2] at [arg3] by user [arg4].Informational
FQXSPPP4004IServer [arg1] [arg2] cleared by user [arg3].Informational
FQXSPPP4005IThe power cap value changed from [arg1] watts to [arg2] watts by user [arg3].Informational
FQXSPPP4006IThe minimum power cap value changed from [arg1] watts to [arg2] watts.Informational
FQXSPPP4007IThe maximum power cap value changed from [arg1] watts to [arg2] watts.Informational
FQXSPPP4008IThe soft minimum power cap value changed from [arg1] watts to [arg2] watts.Informational
FQXSPPP4011IPower capping was activated by user [arg1].Informational
FQXSPPP4012IPower capping was deactivated by user [arg1].Informational
FQXSPPP4013IStatic Power Savings mode has been turned on by user [arg1].Informational
FQXSPPP4014IStatic Power Savings mode has been turned off by user [arg1].Informational
FQXSPPP4015IDynamic Power Savings mode has been turned on by user [arg1].Informational
FQXSPPP4016IDynamic Power Savings mode has been turned off by user [arg1].Informational
FQXSPPP4017IPower cap and external throttling occurred.Informational
FQXSPPP4018IExternal throttling occurred .Informational
FQXSPPP4019IPower cap throttling occurred.Informational
FQXSPPP4020IThe measured power value has returned below the power cap value.Informational
FQXSPPP4021IThe new minimum power cap value has returned below the power cap value.Informational
FQXSPPP4022IThe server was restarted for an unknown reason.Informational
FQXSPPP4023IThe server is restarted by chassis control command.Informational
FQXSPPP4024IThe server was reset via push button.Informational
FQXSPPP4025IThe server was powered-up via power push button.Informational
FQXSPPP4026IThe server was restarted when the watchdog expired..Informational
FQXSPPP4027IThe server was restarted for OEM reason.Informational
FQXSPPP4028IThe server was automatically powered on because the power restore policy is set to always on.Informational
FQXSPPP4029IThe server was automatically powered on because the power restore policy is set to restore previous power state..Informational
FQXSPPP4030IThe server was reset via Platform Event Filter.Informational
FQXSPPP4031IThe server was power-cycled via Platform Event Filter.Informational
FQXSPPP4032IThe server was soft reset.Informational
FQXSPPP4033IThe server was powered up via Real Time Clock (scheduled power on).Informational
FQXSPPP4034IThe server was powered off for an unknown reason.Informational
FQXSPPP4035IThe server was powered off by chassis control command.Informational
FQXSPPP4036IThe server was powered off via push button.Informational
FQXSPPP4037IThe server was powered off when the watchdog expired.Informational
FQXSPPP4038IThe server stayed powered off because the power restore policy is set to always off.Informational
FQXSPPP4039IThe server stayed powered off because the power restore policy is set to restore previous power state..Informational
FQXSPPP4040IThe server was powered off via Platform Event Filter.Informational
FQXSPPP4041IThe server was powered off via Real Time Clock (scheduled power off).Informational
FQXSPPP4042IManagement Controller [arg1] reset was initiated due to Power-On-Reset.Informational
FQXSPPP4043IManagement Controller [arg1] reset was initiated by PRESET.Informational
FQXSPPP4044IManagement Controller [arg1] reset was initiated by CMM.Informational
FQXSPPP4045IManagement Controller [arg1] reset was initiated by XCC firmware.Informational
FQXSPPP4046IRemote power permission is [arg1].Informational
FQXSPPP4047IManagement Controller [arg1] reset was initiated by user [arg2].Informational
FQXSPPP4048IAttempting to AC power cycle server [arg1] by user [arg2].Informational
FQXSPPP4049IManagement Controller [arg1] reset was initiated by Front Panel.Informational
FQXSPPP4050IManagement Controller [arg1] reset was initiated to activate PFR Firmware.Informational
FQXSPPP4051IThe progrmmable GPU total power capping value in slot [arg1] is changed to [arg2] watts by user [arg3] from [arg4] at IP address [arg5].Informational
FQXSPPP4052IThe progrmmable GPU peak power capping value in slot [arg1] is changed to [arg2] watts by user [arg3] from [arg4] at IP address [arg5].Informational
FQXSPPP4053IThis message is reserved.Informational
FQXSPPP4054IUnbalanced PSU config is detected, system is using less node PSU capacity.Informational
FQXSPPR0001I[ManagedElementName] detected as absent.Informational
FQXSPPR0002I[ManagedElementName] has been disabled.Informational
FQXSPPR2000I[ManagedElementName] detected as present.Informational
FQXSPPR2002I[ManagedElementName] has been enabled.Informational
FQXSPPU0008I[ProcessorElementName] has been Disabled.Informational
FQXSPPU2001IAn Over-Temperature Condition has been removed on [ProcessorElementName].Informational
FQXSPPU2002IThe Processor [ProcessorElementName] is no longer operating in a Degraded State.Informational
FQXSPPU2003I[ProcessorElementName] has Recovered from IERR.Informational
FQXSPPU2004I[ProcessorElementName] has Recovered from FRB1/BIST condition.Informational
FQXSPPU2008I[ProcessorElementName] has been Enabled.Informational
FQXSPPU2009I[ProcessorElementName] has Recovered from a Configuration Mismatch.Informational
FQXSPPU2011IAn SM BIOS Uncorrectable CPU complex error for [ProcessorElementName] has deasserted.Informational
FQXSPPW0008I[SensorElementName] has been turned off.Informational
FQXSPPW0009I[PowerSupplyElementName] has been Power Cycled.Informational
FQXSPPW2008I[PowerSupplyElementName] has been turned on.Informational
FQXSPPW2035INumeric sensor [NumericSensorElementName] going low (lower critical) has deasserted.Informational
FQXSPPW2047INumeric sensor [NumericSensorElementName] going high (upper critical) has deasserted.Informational
FQXSPPW2063ISensor [SensorElementName] has transitioned to a less severe state from critical.Informational
FQXSPPW4001IPCIe Power Brake for [arg1] has been [arg2].Informational
FQXSPPW4003IThe customized total graphics power is within the pre-configured limit.Informational
FQXSPSD0000IThe [StorageVolumeElementName] has been added.Informational
FQXSPSD0003IHot Spare enabled for [ComputerSystemElementName].Informational
FQXSPSD0007IRebuild in progress for Array in system [ComputerSystemElementName].Informational
FQXSPSD2000IThe [StorageVolumeElementName] has been removed from unit [PhysicalPackageElementName].Informational
FQXSPSD2001IThe [StorageVolumeElementName] has recovered from a fault.Informational
FQXSPSD2002IFailure no longer Predicted on [StorageVolumeElementName] for array [ComputerSystemElementName].Informational
FQXSPSD2003IHot spare disabled for [ComputerSystemElementName].Informational
FQXSPSD2005ICritical Array [ComputerSystemElementName] has deasserted.Informational
FQXSPSD2006IArray in system [ComputerSystemElementName] has been restored.Informational
FQXSPSD2007IRebuild completed for Array in system [ComputerSystemElementName].Informational
FQXSPSE4001IRemote Login Successful. Login ID: [arg1] using [arg2] from [arg3] at IP address [arg4].Informational
FQXSPSE4002ISecurity: Userid: [arg1] using [arg2] had [arg3] login failures from WEB client at IP address [arg4].Informational
FQXSPSE4003ISecurity: Login ID: [arg1] had [arg2] login failures from CLI at [arg3].Informational
FQXSPSE4004IRemote access attempt failed. Invalid userid or password received. Userid is [arg1] from WEB browser at IP address [arg2].Informational
FQXSPSE4005IRemote access attempt failed. Invalid userid or password received. Userid is [arg1] from TELNET client at IP address [arg2].Informational
FQXSPSE4007ISecurity: Userid: [arg1] using [arg2] had [arg3] login failures from an SSH client at IP address [arg4].Informational
FQXSPSE4008ISNMPv1 [arg1] set by user [arg2]: Name=[arg3], AccessType=[arg4], Address=[arg5], .Informational
FQXSPSE4009ILDAP Server configuration set by user [arg1]: SelectionMethod=[arg2], DomainName=[arg3], Server1=[arg4], Server2=[arg5], Server3=[arg6], Server4=[arg7].Informational
FQXSPSE4010ILDAP set by user [arg1]: RootDN=[arg2], UIDSearchAttribute=[arg3], BindingMethod=[arg4], EnhancedRBS=[arg5], TargetName=[arg6], GroupFilter=[arg7], GroupAttribute=[arg8], LoginAttribute=[arg9].Informational
FQXSPSE4011ISecure Web services (HTTPS) [arg1] by user [arg2].Informational
FQXSPSE4012ISecure CIM/XML(HTTPS) [arg1] by user [arg2].Informational
FQXSPSE4013ISecure LDAP [arg1] by user [arg2].Informational
FQXSPSE4014ISSH [arg1] by user [arg2].Informational
FQXSPSE4015IGlobal Login General Settings set by user [arg1]: AuthenticationMethod=[arg2], LockoutPeriod=[arg3], SessionTimeout=[arg4].Informational
FQXSPSE4016IGlobal Login Account Security set by user [arg1]: PasswordRequired=[arg2], PasswordExpirationPeriod=[arg3], MinimumPasswordReuseCycle=[arg4], MinimumPasswordLength=[arg5], MinimumPasswordChangeInterval=[arg6], MaxmumLoginFailures=[arg7], LockoutAfterMaxFailures=[arg8].Informational
FQXSPSE4017IUser [arg1] created.Informational
FQXSPSE4018IUser [arg1] removed.Informational
FQXSPSE4019IUser [arg1] password modified.Informational
FQXSPSE4020IUser [arg1] role set to [arg2].Informational
FQXSPSE4021IUser [arg1] custom privileges set: [arg2][arg3][arg4][arg5][arg6][arg7][arg8][arg9].Informational
FQXSPSE4022IUser [arg1] for SNMPv3 set: AuthenticationProtocol=[arg2], PrivacyProtocol=[arg3], AccessType=[arg4], HostforTraps=[arg5] by user [arg6] from [arg7] at IP address [arg8].Informational
FQXSPSE4023ISSH Client key added for user [arg1] by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPSE4024ISSH Client key imported for user [arg1] from [arg2] by user [arg3] from [arg4] at IP address [arg5].Informational
FQXSPSE4025ISSH Client key removed from user [arg1] by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPSE4026ISecurity: Userid: [arg1] had [arg2] login failures from a CIM client at IP address [arg3].Informational
FQXSPSE4027IRemote access attempt failed. Invalid userid or password received. Userid is [arg1] from a CIM client at IP address [arg2].Informational
FQXSPSE4028ISecurity: Userid: [arg1] had [arg2] login failures from IPMI client at IP address [arg3].Informational
FQXSPSE4029ISecurity: Userid: [arg1] had [arg2] login failures from SNMP client at IP address [arg3].Informational
FQXSPSE4030ISecurity: Userid: [arg1] had [arg2] login failures from IPMI serial client.Informational
FQXSPSE4031IRemote Login Successful. Login ID: [arg1] from [arg2] serial interface.Informational
FQXSPSE4032ILogin ID: [arg1] from [arg2] at IP address [arg3] has logged off.Informational
FQXSPSE4033ILogin ID: [arg1] from [arg2] at IP address [arg3] has been logged off.Informational
FQXSPSE4034IUser [arg1] has removed a certificate.Informational
FQXSPSE4035IA certificate has been revoked .Informational
FQXSPSE4036IThe [arg1] certificate is expired and has been removed.Informational
FQXSPSE4037ICrypto mode modified from [arg1] to [arg2] by user [arg3].Informational
FQXSPSE4038IMinimum TLS level modified from [arg1] to [arg2] by user [arg3].Informational
FQXSPSE4039ITemporary user account [arg1] is created by inband tool.Informational
FQXSPSE4040ITemporary user account [arg1] expires.Informational
FQXSPSE4041ISecurity: Userid: [arg1] had [arg2] login failures from a SFTP client at IP address [arg3].Informational
FQXSPSE4042IThe third-party password function [arg1] by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPSE4043IRetrieving the third-party password [arg1] by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPSE4044IUser [arg1] third-party hashed password has been [arg2] by user [arg3] from [arg4] at IP address [arg5].Informational
FQXSPSE4045IThe Salt of user [arg1] third-party password has been [arg2] by user [arg3] from [arg4] at IP address [arg5].Informational
FQXSPSE4046IThe third-party password of the user [arg1] has been retrieved by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPSE4047IRole [arg1] is [arg2] and assigned with custom privileges [arg3][arg4][arg5][arg6][arg7][arg8][arg9][arg10][arg11] by user [arg12] .Informational
FQXSPSE4048IRole [arg1] is removed by user [arg2].Informational
FQXSPSE4049IRole [arg1] is assigned to user [arg2] by user [arg3].Informational
FQXSPSE4050I[arg1] sent IPMI command from [arg2], raw data: [arg3][arg4][arg5].Informational
FQXSPSE4051IManagement Controller [arg1] joined the neighbor group [arg2] by user [arg3] at IP address [arg4].Informational
FQXSPSE4052IThe password of neighbor group [arg1] is modified by [arg2] [arg3] at IP address [arg4].Informational
FQXSPSE4053IManagement Controller [arg1] left the neighbor group [arg2] by user [arg3] at IP address [arg4].Informational
FQXSPSE4054IIPMI SEL wrapping mode is [arg1] by user [arg2] at IP address [arg3].Informational
FQXSPSE4055ISED encryption is enabled by user [arg1] at IP address [arg2].Informational
FQXSPSE4056ISED AK is [arg1] by user [arg2] at IP address [arg3].Informational
FQXSPSE4057IUser [arg1] created by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPSE4058IUser [arg1] removed by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPSE4059IUser [arg1] password modified by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPSE4060IUser [arg1] role set to [arg2] by user [arg3] from [arg4] at IP address [arg5].Informational
FQXSPSE4061IUser [arg1] custom privileges set: [arg2][arg3][arg4][arg5][arg6][arg7][arg8][arg9] by user [arg10] from [arg11] at IP address [arg12].Informational
FQXSPSE4062IThe system guard snapshot is captured by user [arg1] from [arg2] at IP address [arg3].Informational
FQXSPSE4063IThe system guard configuration is updated: status=[arg1], hardware inventory=[arg2] and action=[arg3] by user [arg4] from [arg5] at IP address [arg6].Informational
FQXSPSE4064ISNMPv3 engine ID is changed from [arg1] to [arg2] by user [arg3] from [arg4] at IP address [arg5].Informational
FQXSPSE4065ISFTP [arg1] by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPSE4066ISecurity mode is modified from [arg1] to [arg2] by user [arg3] from [arg4] at IP address [arg5].Informational
FQXSPSE4067IUser [arg1] accessible interfaces is set to [arg2][arg3][arg4][arg5][arg6] by user [arg7] from [arg8] at IP address [arg9].Informational
FQXSPSE4068ISecurity: Userid: [arg1] using [arg2] had [arg3] login failures from Redfish client at IP address [arg4].Informational
FQXSPSE4069ILDAP set by user [arg1]: RootDN=[arg2], UIDSearchAttribute=[arg3], BindingMethod=[arg4], TargetName=[arg5], GroupFilter=[arg6], GroupAttribute=[arg7], LoginAttribute=[arg8].Informational
FQXSPSE4070ILockdown mode is [arg1] by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPSE4071IChassis Intrusion detection is [arg1] by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPSE4072IRandom SED AK is regenerated by user [arg1] from [arg2] at IP address [arg3].Informational
FQXSPSE4073IMotion detection is [arg1] by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPSE4074ISecurity mode downgrades because the XCC2 Platinum Upgrade key is expired or deleted.Informational
FQXSPSE4075I[arg1] by KCS to allow secure boot to be enabled by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPSE4076I[arg1] by KCS to allow secure boot to be disabled by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPSE4077IBluetooth button on front panel is [arg1] on server [arg2] by user [arg3] from [arg4] at IP address [arg5].Informational
FQXSPSE4078IBluetooth is [arg1] by pressing bluetooth button on front pannel.Informational
FQXSPSE4079IThe Operator role is [arg1] to contain Remote Console Access permission by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPSE4080IThe user [arg1] attempts to clear CMOS from [arg2] at IP address [arg4].Informational
FQXSPSE4081IBMC returns the valid local cached key to UEFI for SED drives.Informational
FQXSPSE4082IRemote key management server is unaccessable.Informational
FQXSPSE4083IThe local cached key has expired and destroyed it.Informational
FQXSPSE4084IPeriodic connection to remote key management server succeeded.Informational
FQXSPSE4085IPeriodic connection to remote key management server failed.Informational
FQXSPSE4088IThe chassis care-taker node ID is changed from [arg1] to [arg2].Informational
FQXSPSE4089IThe chassis node with node ID [arg1] is inserted.Informational
FQXSPSE4090IThe chassis node with node ID [arg1] is removed.Informational
FQXSPSS4000IManagement Controller Test Alert Generated by [arg1].Informational
FQXSPSS4001IServer General Settings set by user [arg1]: Name=[arg2], Contact=[arg3], Location=[arg4], Room=[arg5], RackID=[arg6], Rack U-position=[arg7], Address=[arg8].Informational
FQXSPSS4002ILicense key for [arg1] added by user [arg2].Informational
FQXSPSS4003ILicense key for [arg1] removed by user [arg2].Informational
FQXSPSS4004ITest Call Home Generated by user [arg1].Informational
FQXSPSS4005IManual Call Home by user [arg1]: [arg2].Informational
FQXSPSS4006ICall Home to [arg1] failed to complete: [arg2].Informational
FQXSPSS4007IThe BMC functionality tier is changed from [arg1] to [arg2].Informational
FQXSPSS4008IThe [arg1] setting has been changed to [arg2] by user [arg3].Informational
FQXSPSS4009ISystem enters LXPM maintenance mode.Informational
FQXSPSS4010ITest Audit Log generated by user [arg1].Informational
FQXSPSS4011IFan speed boost setting is changed from [arg1] to [arg2].Informational
FQXSPTR4000IManagement Controller [arg1] clock has been set from NTP server [arg2].Informational
FQXSPTR4001IDate and Time set by user [arg1]: Date=[arg2], Time-[arg3], DST Auto-adjust=[arg4], Timezone=[arg5].Informational
FQXSPTR4002ISynchronize time setting by user [arg1]: Mode=Sync with NTP Server, NTPServerHost1=[arg2]:[arg3],NTPServerHost2=[arg4]:[arg5],NTPServerHost3=[arg6]:[arg7],NTPServerHost4=[arg8]:[arg9],NTPUpdateFrequency=[arg10].Informational
FQXSPTR4003ISynchronize time setting by user [arg1]: Mode=Sync with server clock.Informational
FQXSPUN0009ISensor [SensorElementName] has asserted.Informational
FQXSPUN0024ISensor [SensorElementName] indicates a monitor state.Informational
FQXSPUN0026IDevice [LogicalDeviceElementName] has been added.Informational
FQXSPUN0056ISensor [SensorElementName] has deasserted.Informational
FQXSPUN2009ISensor [SensorElementName] has deasserted.Informational
FQXSPUN2010ISensor [SensorElementName] has asserted.Informational
FQXSPUN2012ISensor [SensorElementName] has deasserted.Informational
FQXSPUN2018ISensor [SensorElementName] has deasserted the transition from normal to non-critical state.Informational
FQXSPUN2019ISensor [SensorElementName] has transitioned to a less severe state from critical.Informational
FQXSPUN2020ISensor [SensorElementName] has deasserted the transition to non-recoverable from a less severe state.Informational
FQXSPUN2023ISensor [SensorElementName] has deasserted the transition to non-recoverable.Informational
FQXSPUN2026IDevice [LogicalDeviceElementName] has been removed from unit [PhysicalPackageElementName].Informational
FQXSPUN2030IDevice [LogicalDeviceElementName] has been removed from unit [PhysicalPackageElementName].Informational
FQXSPUP4001IFlash of [arg1] from [arg2] succeeded for user [arg3] .Informational
FQXSPUP4002IFlash of [arg1] from [arg2] failed for user [arg3].Informational
FQXSPUP4006IAuto promote primary XCC to backup is [arg1] by user [arg2] from [arg3] at IP address [arg4].Informational
FQXSPUP4007IViolation access to XCC SPI flash is detected and isolated.Informational
FQXSPUP4008IViolation access to UEFI SPI flash is detected and isolated.Informational
FQXSPUP4010IFlash [arg1] of [arg2] from [arg3] succeeded for user [arg4] .Informational
FQXSPUP4011IFlash [arg1] of [arg2] from [arg3] failed for user [arg4].Informational
FQXSPWD0000IWatchdog Timer expired for [WatchdogElementName].Informational
FQXSPWD0001IReboot of system [ComputerSystemElementName] initiated by watchdog [WatchdogElementName].Informational
FQXSPWD0002IPowering off system [ComputerSystemElementName] initiated by watchdog [WatchdogElementName].Informational
FQXSPWD0003IPower cycle of system [ComputerSystemElementName] initiated by watchdog [WatchdogElementName].Informational
FQXSPWD0004IWatchdog Timer interrupt occurred for [WatchdogElementName].Informational
FQXSPBR4001IRunning the backup Management Controller [arg1] main application.Warning
FQXSPCA0007JNumeric sensor [NumericSensorElementName] going high (upper non-critical) has asserted.Warning
FQXSPCA0015JSensor [SensorElementName] has transitioned from normal to non-critical state.Warning
FQXSPDM4002IDevice [arg1] VPD is not valid.Warning
FQXSPEA0003JLink down is detected on port [arg1] of the PCIe device [arg2].Warning
FQXSPEM4040IDust filter measurement is completed. The airflow pathway is obstructed, check and replace the dust filter, or remove any obstructing object.Warning
FQXSPEM4043IA [arg1] failure has been detected and need [arg2] to recover.Warning
FQXSPIO0014JBus [SensorElementName] is operating in a degraded state.Warning
FQXSPIO4001IGPU Board Status was changed by [arg1] of [arg1].Warning
FQXSPMA0010J[PhysicalMemoryElementName] on Subsystem [MemoryElementName] Throttled.Warning
FQXSPMA0011GMemory Logging Limit Reached for [PhysicalMemoryElementName] on Subsystem [MemoryElementName].Warning
FQXSPMA0017JNon-redundant:Sufficient Resources from Redundancy Degraded or Fully Redundant for [RedundancySetElementName] has asserted.Warning
FQXSPMA4034GHealth of DIMM [arg1] is in warning state and sub-state is [arg2].Warning
FQXSPNM4010IDHCP[[arg1]] failure, no IP address assigned.Warning
FQXSPNM4032IDHCPv6 failure, no IP address assigned.Warning
FQXSPPP4009IThe measured power value exceeded the power cap value.Warning
FQXSPPP4010IThe new minimum power cap value exceeded the power cap value.Warning
FQXSPPU0002GThe Processor [ProcessorElementName] is operating in a Degraded State.Warning
FQXSPPU2010GA terminator has not been detected on the processor [ProcessorElementName].Warning
FQXSPPW4002ITotal graphics power value has exceeded the pre-configured limit.Warning
FQXSPSD0002GFailure Predicted on [StorageVolumeElementName] for array [ComputerSystemElementName].Warning
FQXSPUN0009GSensor [SensorElementName] has asserted.Warning
FQXSPUN0018JSensor [SensorElementName] has transitioned from normal to non-critical state.Warning
FQXSPUN0026GDevice [LogicalDeviceElementName] has been added.Warning
FQXSPUN0056GSensor [SensorElementName] has asserted.Warning
FQXSPBR4003IPlatform Watchdog Timer expired for [arg1].Error
FQXSPBR4007IManagement Controller [arg1]: Configuration restoration from a file by user [arg2] failed to complete from [arg3] at IP address [arg4].Error
FQXSPBR4008IManagement Controller [arg1]: Configuration restoration from a file by user [arg2] failed to start from [arg3] at IP address [arg4].Error
FQXSPCA0004NNumeric sensor [NumericSensorElementName] going low (lower non-recoverable) has asserted.Error
FQXSPCA0009MNumeric sensor [NumericSensorElementName] going high (upper critical) has asserted.Error
FQXSPCA0011NNumeric sensor [NumericSensorElementName] going high (upper non-recoverable) has asserted.Error
FQXSPCA0017MSensor [SensorElementName] has transitioned to critical from a less severe state.Error
FQXSPCA0019NSensor [SensorElementName] has transitioned to non-recoverable from a less severe state.Error
FQXSPDA0000NThe System [ComputerSystemElementName] encountered firmware error - no video device detected.Error
FQXSPFW0000NThe System [ComputerSystemElementName] encountered a POST Error.Error
FQXSPFW0001NFirmware BIOS (ROM) corruption was detected on system [ComputerSystemElementName] during POST.Error
FQXSPFW0002NThe System [ComputerSystemElementName] encountered a firmware hang.Error
FQXSPIO0001LThe connector [PhysicalConnectorElementName] has encountered a configuration error.Error
FQXSPIO0004LA bus timeout has occurred on bus [SensorElementName].Error
FQXSPIO0006NA software NMI has occurred on system [ComputerSystemElementName].Error
FQXSPIO0011NAn Uncorrectable Error has occurred on [SensorElementName].Error
FQXSPIO0013NA Fatal Bus Error has occurred on bus [SensorElementName].Error
FQXSPIO0015MFault in slot [PhysicalConnectorSystemElementName] on system [ComputerSystemElementName].Error
FQXSPMA0002NConfiguration Error for [PhysicalMemoryElementName] on Subsystem [MemoryElementName].Error
FQXSPMA0005NSubsystem [MemoryElementName] has insufficient memory for operation.Error
FQXSPMA0006NParity Error for [PhysicalMemoryElementName] on Subsystem [MemoryElementName].Error
FQXSPMA0007LScrub Failure for [PhysicalMemoryElementName] on Subsystem [MemoryElementName].Error
FQXSPMA0008NUncorrectable error detected for [PhysicalMemoryElementName] on Subsystem [MemoryElementName].Error
FQXSPMA0012MAn Over-Temperature Condition has been detected on the [PhysicalMemoryElementName] on Subsystem [MemoryElementName].Error
FQXSPMA0013NThe System [ComputerSystemElementName] has detected no memory in the system.Error
FQXSPMA0015LRedundancy Lost for [RedundancySetElementName] has asserted.Error
FQXSPMA0019MNon-redundant:Insufficient Resources for [RedundancySetElementName] has asserted.Error
FQXSPMA4035MHealth of DIMM [arg1] is in error state and sub-state is [arg2].Error
FQXSPOS4002IWatchdog [arg1] Failed to Capture Screen.Error
FQXSPOS4003IPlatform Watchdog Timer expired for [arg1].Error
FQXSPOS4010IOS Crash Video Capture Failed.Error
FQXSPPU0001NAn Over-Temperature Condition has been detected on [ProcessorElementName].Error
FQXSPPU0003N[ProcessorElementName] has Failed with IERR.Error
FQXSPPU0004M[ProcessorElementName] has Failed with FRB1/BIST condition.Error
FQXSPPU0009N[ProcessorElementName] has a Configuration Mismatch.Error
FQXSPPU0011NAn SM BIOS Uncorrectable CPU complex error for [ProcessorElementName] has asserted.Error
FQXSPPW0016KPower Control of System [ComputerSystemElementName] has failed.Error
FQXSPPW0035MNumeric sensor [NumericSensorElementName] going low (lower critical) has asserted.Error
FQXSPPW0047MNumeric sensor [NumericSensorElementName] going high (upper critical) has asserted.Error
FQXSPPW0063MSensor [SensorElementName] has transitioned to critical from a less severe state.Error
FQXSPSB0000NThe System [ComputerSystemElementName] has encountered a motherboard failure.Error
FQXSPSD0001LThe [StorageVolumeElementName] has a fault.Error
FQXSPSD0005LArray [ComputerSystemElementName] is in critical condition.Error
FQXSPSD0006LArray [ComputerSystemElementName] has failed.Error
FQXSPSE4000ICertificate Authority [arg1] has detected a [arg2] Certificate Error.Error
FQXSPUN0019MSensor [SensorElementName] has transitioned to critical from a less severe state.Error
FQXSPUN0020NSensor [SensorElementName] has transitioned to non-recoverable from a less severe state.Error
FQXSPUN0023NSensor [SensorElementName] has transitioned to non-recoverable.Error
FQXSPUN0047NSensor [SensorElementName] has transitioned to non-recoverable.Error
FQXSPUP0007LInvalid or Unsupported firmware or software was detected on system [ComputerSystemElementName].Error
FQXSPUP4000IPlease ensure that the Management Controller [arg1] is flashed with the correct firmware. The Management Controller is unable to match its firmware to the server.Error
FQXSPUP4003I[arg1] firmware mismatch internal to system [arg2]. Please attempt to flash the [arg3] firmware.Error
FQXSPUP4004IXCC firmware mismatch between nodes/servers [arg1] and [arg2]. Please attempt to flash the XCC firmware to the same level on all nodes/servers.Error
FQXSPUP4005IFPGA firmware mismatch between nodes/servers [arg1] and [arg2]. Please attempt to flash the FPGA firmware to the same level on all nodes/servers.Error
FQXSPUP4009IPlease ensure that the system is flashed with the correct [arg1] firmware. The Management Controller is unable to match the firmware to the server.Error