Skip to main content

Rear view

The rear view of the server varies by model. Depending on the model, your server might look slightly different from the illustrations in this topic.

Rear view of 3 x PCIe slots configuration

The following illustration shows the rear view of server model with three PCIe slots. Depending on the model, your server might look slightly different from the illustration below.
Figure 1. Rear view with two low profile and one full height PCIe adapters
Rear view of 3 x PCIe slot configuration
1 Power supply unit 12 PCIe slot 1 on riser 1 assembly
3 PCIe slot 2 on riser 1 assembly4 System ID LED
5 System error LED6 RoT fault LED
7 PCIe slot 3 on riser 2 assembly8 Power supply unit 2
9 Ethernet connectors on rear OCP module 2 (optional)10 XCC system management port (10/100/1000 Mbps RJ-45)
11 USB 3.2 Gen 1 (5Gbps) connector with USB 2.0 XCC system management (depending on the configuration)12 USB 3.2 Gen 1 (5Gbps) connectors
13 VGA connector14 Ethernet connectors on rear OCP module 1 (optional)
Note
For more information about each component, see Rear components overview.

Rear view of 2 x PCIe slots configuration

The following illustration shows the rear views of the server model with two PCIe slots. Depending on the model, your server might look slightly different from the illustration below.
Figure 2. Rear view with two full height PCIe adapters
Rear view of 2 x PCIe slot configuration
1 Power supply unit 12 PCIe slot 1 on riser 1 assembly
3 System ID LED4 System error LED
5 RoT fault LED6 PCIe slot 3 on riser 2 assembly
7 Power supply unit 28 Ethernet connectors on rear OCP module 2 (optional)
9 XCC system management port (10/100/1000 Mbps RJ-45)10 USB 3.2 Gen 1 (5Gbps) connector with USB 2.0 XCC system management (depending on the configuration)
11 USB 3.2 Gen 1 (5Gbps) connectors12 VGA connector
13 Ethernet connectors on rear OCP module 1 (optional) 
Figure 3. Rear view with one low profile and one full height PCIe adapter
Rear view of server model with two PCIe slots
1 Power supply unit 12 PCIe slot 1 on riser 1 assembly
3 PCIe slot 2 on riser 1 assembly4 System ID LED
5 System error LED6 RoT fault LED
7 Rear M.2 assembly8 Power supply unit 2
9 Ethernet connectors on rear OCP module 2 (optional)10 XCC system management port (10/100/1000 Mbps RJ-45)
11 USB 3.2 Gen 1 (5Gbps) connector with USB 2.0 XCC system management (depending on the configuration)12 USB 3.2 Gen 1 (5Gbps) connectors
13 VGA connector14 Ethernet connectors on rear OCP module 1 (optional)
Note
For more information about each component, see Rear components overview.

Rear view of 2 x 2.5-inch drives and 1 x PCIe slot configuration

The following illustration shows the rear view of the server model with two hot-swap drive bays and one PCIe slot. Depending on the model, your server might look slightly different from the illustration below.
Figure 4. Rear view of 2 x 2.5-inch drive and 1 x PCIe slot configuration
Rear view of 2 x 2.5-inch drive and 1 x PCIe slot configuration
1 Power supply unit 12 PCIe slot 1 on riser 1 assembly
3 Rear 2.5-inch drive bays (2)4 System ID LED
5 System error LED6 RoT fault LED
7 Power supply unit 28 Ethernet connectors on rear OCP module 2 (optional)
9 XCC system management port (10/100/1000 Mbps RJ-45)10 USB 3.2 Gen 1 (5Gbps) connector with USB 2.0 XCC system management (depending on the configuration)
11 USB 3.2 Gen 1 (5Gbps) connectors12 VGA connector
13 Ethernet connectors on rear OCP module 1 (optional) 
Note
For more information about each component, see Rear components overview.

Rear view of 2 x PCIe slots and 1 x Processor Neptune Core Module configuration

The following illustration shows the rear view of the server model with two PCIe slots and a Processor Neptune® Core Module (NeptCore). Depending on the model, your server might look slightly different from the illustration below.

Rear view of 2 x PCIe slots and 1 x Processor Neptune Core Module (NeptCore) configuration
1 Power supply unit 12 PCIe slot 1 on riser 1 assembly
3 Hose holder4 Inlet hose
5 Outlet hose6 PCIe slot 3 on riser 2 assembly
7 Power supply unit 18 Ethernet connectors on rear OCP module 2 (optional)
9 RoT fault LED10 System error LED
11 System ID LED12 XCC system management port (10/100/1000 Mbps RJ-45)
13 USB 3.2 Gen 1 (5Gbps) connector with USB 2.0 XCC system management (depending on the configuration)14 USB 3.2 Gen 1 (5Gbps) connectors
15 VGA connector16 Ethernet connectors on rear OCP module 1 (optional)
Note
For more information about each component, see Rear components overview.

Rear view of 1 x NeptCore module and 2 x rear M.2 drives configuration

The following illustration shows the rear view of the server model with a Processor Neptune Core Module and rear M.2 drives. Depending on the model, your server might look slightly different from the illustration below.

Rear view of server model with two rear M.2 drives and a Processor Neptune Core Module (NeptCore) configuration
Table 1. Components on the rear of the server
1 Power supply unit 12 PCIe slot 1 on riser 1 assembly
3 Hose holder4 Inlet hose
5 Outlet hose6 System ID LED
7 System error LED8 RoT fault LED
9 Rear M.2 drive assembly10 Power supply unit 2
11 Ethernet connectors on rear OCP module 2 (optional)12 XCC system management port (10/100/1000 Mbps RJ-45)
13 USB 3.2 Gen 1 (5Gbps) connector with USB 2.0 XCC system management (depending on the configuration)14 USB 3.2 Gen 1 (5Gbps) connectors
15 VGA connector16 Ethernet connectors on rear OCP module 1 (optional)

Rear components overview

Ethernet connectors

Figure 5. OCP module (two connectors)
OCP module (two connectors, seen from the rear)

Figure 6. OCP module (four connectors)
OCP module (four connectors, seen from the rear)

  • The OCP module provides two or four extra Ethernet connectors for network connections.

  • By default, any Ethernet connector on the OCP module can also function as a management connector using the shared management capacity.

Note
  • The server features two OCP slots: OCP 1 and OCP 2, which are located on the rear side.

  • The installation priority of OCP slots in configurations with two processors is as follows:

    • Configurations with only one OCP module: A x8 OCP module is installed in OCP slot 1; a x16 OCP module is installed in OCP slot 2.

    • Configurations with two OCP modules: OCP slot 1 > OCP slot 2; x16 > x8

  • OCP module 1 take priority over OCP module 2.

Hot-swap drives and drive bays

The drive bays on the front and rear of your server are designed for hot-swap drives. The number of the installed drives in your server varies by model. When you install drives, follow the order of the drive bay numbers.

The EMI integrity and cooling of the server are protected by having all drive bays occupied. Vacant drive bays must be occupied by drive fillers.

PCIe slots

The PCIe slots are on the rear of the server and your server supports up to three PCIe slots on riser 1 and 2 assemblies.

Power supply units

The hot-swap redundant power supply helps you avoid significant interruption to the operation of the system when a power supply fails. You can purchase a power supply option from Lenovo and install the power supply to provide power redundancy without turning off the server.

On each power supply, there are three status LEDs near the power cord connector. For information about the LEDs, see System LEDs and diagnostics display.

USB 3.2 Gen 1 (5Gbps) connector with USB 2.0 XCC system management (depending on the configuration)

The connector can function as a regular USB 3.2 Gen 1 connector to the host OS; it can be used to attach a USB-compatible device, such as a USB keyboard, USB mouse, or USB storage device.

When there are no USB connectors at the front, this connector can function as a USB 2.0 Lenovo XClarity Controller management port. Connection to Lenovo XClarity Controller is primarily intended for users with a mobile device running the Lenovo XClarity Controller mobile application. When a mobile device is connected to this USB port, an Ethernet over USB connection is established between the mobile application running on the device and the Lenovo XClarity Controller.

For details about using the Lenovo XClarity Mobile app, refer to Lenovo XClarity Administrator Mobile app online documentation.

VGA connector

The VGA connectors at the rear of the server can be used to attach a high-performance monitor, a direct-drive monitor, or other devices that use a VGA connector.

XCC system management port (10/100/1000 Mbps RJ-45)

The XClarity Controller network connector can be used to attach an Ethernet cable to manage the baseboard management controller (BMC).

Rear LEDs

Inlet and outlet hoses

The Processor Neptune Core Module spreads two hoses out to connect to the manifolds. The inlet hose conveys warm water from the facility to the cold plates to cool down the processors, and the outlet hose conducts hot water out of the Processor Neptune Core Module to realize system cooling.