Skip to main content

Remove the front adapter cage

Follow instructions in this section to remove the front adapter cage, including the riser 5 cage at the top and the front OCP cage at the bottom.

About this task

Attention

  • Read Installation Guidelines and Safety inspection checklist to ensure that you work safely.

  • Power off the server and peripheral devices and disconnect the power cords and all external cables. See Power off the server.

  • Prevent exposure to static electricity, which might lead to system halt and loss of data, by keeping static-sensitive components in their static-protective packages until installation, and handling these devices with an electrostatic-discharge wrist strap or other grounding system.

  • Before you remove any component of a RAID array (drive, RAID card, etc.), back up all RAID configuration information.

Procedure

  1. Make preparation for the task.
    1. If the server is installed in a rack, slide the server out on its rack slide rails to gain access to the top cover, or remove the server from the rack. See Remove the server from rack.
    2. Remove the top cover. See Remove the top cover.
    3. If your server comes with a riser 1 assembly, remove it first. See Remove a rear riser assembly. Then disconnect the cables from the rear OCP interposer card.
    4. Remove the air baffle. See Remove the air baffle.
    5. Remove the system fan cage. See Remove the system fan cage.
    6. Record the cable connections, and disconnect all cables from the system board assembly.
      Note

      • If you need to disconnect cables from the system board assembly, disengage all latches or release tabs on cable connectors first. Failing to release the tab before removing the cables will damage the cable sockets on the system board assembly. Any damage to the cable sockets might require replacing the system board assembly.

      • The connectors on your system board assembly might look different from those in the illustration, but the removal procedure is the same.

        1. Press the release tab to release the connector.

        2. Disengage the connector from the cable socket.

  2. Remove the front adapter assembly.
    Note
    The number of cables varies according to the configuration.
    Figure 1. Removing the front adapter assembly
    Removing the front adapter assembly

    1. Remove the screws that secure the assembly.
    2. Slide the assembly out of the front chassis.
  3. Lift the riser 5 assembly up off the front OCP assembly, and disconnect cables from the front OCP interposer card.
    Figure 2. Lifting the riser 5 assembly
    Lifting the riser 5 assembly

  4. Remove the PCIe adapter from the riser 5 cage.
    Note
    For ThinkSystem AMD X3522 10/25GbE DSFP28 2-port PCIe Ethernet Adapter, remove the screw that secures the adapter first.
    Figure 3. Removing the PCIe adapter from the riser 5 cage
    Removing the PCIe adapter from the riser 5 cage

    1. Press the retainer clip downward.
    2. Rotate the retention latch to the open position.
    3. Grasp the PCIe adapter by its edges and carefully pull it out of the PCIe slot.
  5. Disconnect the cables from the riser card, and remove the riser card from the riser 5 cage.
    Figure 4. Removing the riser card from the riser 5 cage
    Removing the riser card from the riser 5 cage

    1. Remove the screws that secure the riser card.
    2. Rotate the riser card from the top to disengage it from the screw holes on the riser cage.
    3. Lift the riser card out of the riser cage.
  6. Remove the OCP module from the front OCP cage.
    Figure 5. Removing the OCP module
    Removing the OCP module

    1. Loosen the thumbscrew that secures the OCP module.
    2. Pull out the OCP module.
  7. Remove the front OCP interposer card.
    Figure 6. Removing the front OCP interposer card
    Removing the front OCP interposer card

    1. Loosen the screws that secure the front OCP interposer card.
    2. Lift the front OCP interposer card up off the front OCP cage.

After you finish

  1. Install the new front adapter cage. See Install the front adapter cage.

  2. If you are instructed to return the component or optional device, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you.

Demo video

Watch the procedure on YouTube