Hardware replacement procedures
This section provides installation and removal procedures for all serviceable system components. Each component replacement procedure references any tasks that need to be performed to gain access to the component being replaced.
- Installation Guidelines
Before installing components in your server, read the installation guidelines. - Technical rules
Refer to the below technical rules and limitations when you install the related server components. - Power on and power off the server
Follow the instructions in this section to power on and power off the server. - Server replacement
Follow instructions in this section to remove and install the server. - CMOS battery (CR2032) replacement
Use this information to remove and install the CMOS battery. - EDSFF cage replacement
Use this information to remove and install an EDSFF cage - Front drive backplane replacement
Use this information to remove and install a front drive backplane. - Front riser assembly replacement
A complete front riser assembly consists of two front riser cages, two front riser cards and two PCIe adapters. See this topic to understand how to remove and assemble a front riser assembly. - Front OCP module and OCP interposer card replacement
Some server models support the front OCP module. The front OCP module and the front and rear OCP interposer cards are codependent. Follow instructions in this section to remove and install the front OCP module and the front and rear OCP interposer cards. - Front I/O module replacement
Use this information to remove and install the front I/O module. - GPU replacement
Use this information to remove and install a GPU adapter. - Hot-swap drive replacement
Use this information to remove and install a hot-swap drive. You can remove or install a hot-swap drive without turning off the server, which helps you avoid significant interruption to the operation of the system. - Internal CFF HBA/RAID adapter replacement
Use this information to remove and install the internal CFF HBA/RAID adapter. - Intrusion switch replacement
Use this information to remove and install an intrusion switch. The intrusion switch informs you that the server cover is not properly installed or closed by creating an event in the system event log (SEL). - The Lenovo Neptune Liquid to Air Module replacement (trained technicians only)
Follow instructions in this section to remove and install the L2AM (The Lenovo Neptune Liquid to Air Module). - Lenovo Neptune(TM) Processor Direct Water Cooling Module replacement (trained technicians only)
Follow the instructions in this section to remove and install the Direct Water Cooling Module (DWCM). - Management NIC adapter replacement
Follow instructions in this section to install or remove the ThinkSystem V3 Management NIC Adapter Kit (management NIC adapter). - Manifold replacement (trained technicians only)
Use the following procedures to remove and install the manifolds. - Memory module replacement
Use the following procedures to remove and install a memory module. - MicroSD card replacement
Follow the instructions in this section to remove and install the MicroSD card. - M.2 backplane and M.2 drive replacement
Use this information to remove and install the M.2 backplane and M.2 drive (an assembled M.2 backplane and M.2 drive is also known as M.2 module). - OCP module replacement
Use this information to remove and install the OCP module. - PCIe adapter replacement
Use this information to remove and install a PCIe adapter. - Power supply unit replacement
Use this information to remove and install a power supply unit. - Power-supply-unit air baffle replacement
Use this information to remove and install a power-supply-unit air baffle. - Processor and heat sink replacement (trained technicians only)
Use this information to remove and install a processor or a heat sink. - Rack latches replacement
Use this information to remove and install the rack latches. - RAID flash power module replacement
The RAID flash power module protects the cache memory on the installed RAID adapter. You can purchase a RAID flash power module from Lenovo. Use this information to remove and install a RAID flash power module (also called super capacitor). - Rear drive assembly replacement
Use this information to remove and install the rear drive assembly. - Rear drive backplane replacement
Use this information to remove and install a rear drive backplane. - Rear riser assembly replacement
Use this information to remove and install the riser assembly. - Security bezel replacement
Use this information to remove and install the security bezel. - Serial port module replacement
Use this information to remove and install a serial port module. - System board (system board assembly) replacement (trained technicians only)
Follow instructions in this section to remove and install the system I/O board and processor board, which assembled as a system board (system board assembly). - System fan replacement
Use this information to remove and install a system fan. - Top cover replacement
Follow instructions in this section to remove and install the top cover. - Complete the parts replacement
Go through the checklist to complete parts replacement
Give documentation feedback