Parts list

Use the parts list to identify each of the components that are available for your server.

For more information about ordering the parts shown in Figure 1:

It is highly recommended that you check the power summary data for your server using Lenovo Capacity Planner before purchasing any new parts.

Note

Depending on the model, your server might look slightly different from the illustration.

Figure 1. Server components

Graphic showing all parts associated with the server

The parts listed in the following table are identified as one of the following:

Tier 1 customer replaceable unit (CRU): Replacement of Tier 1 CRUs is your responsibility. If Lenovo installs a Tier 1 CRU at your request with no service agreement, you will be charged for the installation.
Tier 2 customer replaceable unit (CRU): You may install a Tier 2 CRU yourself or request Lenovo to install it, at no additional charge, under the type of warranty service that is designated for your server.
Field replaceable unit (FRU): FRUs must be installed only by trained service technicians.
Consumable and Structural parts: Purchase and replacement of consumable and structural parts is your responsibility. If Lenovo acquires or installs a structural component at your request, you will be charged for the service.

Note

Unless otherwise specified in other agreements or contract terms, parts beyond their warranty terms and/or parts that have reached their maximum usage limitations do not qualify for warranty service.

Table 1. Parts list
Index	Description	Tier 1 CRU	Tier 2 CRU	FRU	Consumable and Structural parts
For more information about ordering the parts shown in Figure 1: Parts list
`1`	Top cover	√
`2`	Standard air baffle	√
`3`	Riser assembly (LP)	√
`4`	Riser assembly (LP+LP)	√
`5`	Riser assembly (LP+FH)	√
`6`	Rear wall bracket				√
`7`	PCIe adapter	√
`8`	System board			√
`9`	RAID flash power module holder (on chassis)				√
`10`	RAID flash power module holder (in riser cage)				√
`11`	RAID flash power module	√
`12`	OCP 3.0 Ethernet adapter	√
`13`	Power supply unit	√
`14`	Power supply unit filler				√
`15`	Front I/O assembly with diagnostics panel (right)	√
`16`	Front I/O assembly	√
`17`	External LCD diagnostics handset	√
`18`	LCD diagnostics panel assembly	√
`19`	EIA (right)				√
`20`	LCD diagnostics panel	√
`21`	Front I/O assembly with diagnostics panel (top)	√
`22`	2.5-inch drive bay filler				√
`23`	2.5-inch drive	√
`24`	3.5-inch drive	√
`25`	7mm drive cage	√
`26`	7mm drive backplane (bottom)		√
`27`	7mm drive backplane (top)		√
`28`	4-EDSFF cage	√
`29`	7mm drive	√
`30`	7mm drive bay filler				√
`31`	EDSFF drive	√
`32`	Security bezel	√
`33`	4 x 2.5-inch front drive backplane	√
`34`	16-EDSFF front drive backplane	√
`35`	8 x 2.5-inch front drive backplane	√
`36`	10 x 2.5-inch front drive backplane		√
`37`	4 x 3.5-inch front drive backplane	√
`38`	2 x 2.5-inch rear drive cage	√
`39`	2 x 2.5-inch rear drive backplane	√
`40`	Internal RAID module		√
`41`	Intrusion switch cable	√
`42`	Fan module	√
`43`	Memory module	√
`44`	Chassis			√
`45`	Heat sink PEEK nut		√
`46`	Standard heat sink			√
`47`	Performance heat sink (T-shape)			√
`48`	Processor			√
`49`	M.2 drive	√
`50`	M.2 backplane	√
`51`	TPM adapter (for Chinese Mainland only)			√
`52`	M.2 retainer clip	√
`53`	CMOS battery (CR2032)				√

Give documentation feedback