Parts list

Use the parts list to identify each of the components that are available for your server.

For more information about ordering the parts shown in Figure 1:

It is highly recommended that you check the power summary data for your server using Lenovo Capacity Planner before purchasing any new parts.

Note

Depending on the model, your server might look slightly different from the illustration.

Figure 1. Server components

Graphic showing all parts associated with the server

The parts listed in the following table are identified as one of the following:

Tier 1 customer replaceable unit (CRU): Replacement of Tier 1 CRUs is your responsibility. If Lenovo installs a Tier 1 CRU at your request with no service agreement, you will be charged for the installation.
Tier 2 customer replaceable unit (CRU): You may install a Tier 2 CRU yourself or request Lenovo to install it, at no additional charge, under the type of warranty service that is designated for your server.
Field replaceable unit (FRU): FRUs must be installed only by trained service technicians.
Consumable and Structural parts: Purchase and replacement of consumable and structural parts is your responsibility. If Lenovo acquires or installs a structural component at your request, you will be charged for the service.

Table 1. Parts list
Index	Description	Tier 1 CRU	FRU	Consumable and Structural parts
For more information about ordering the parts shown in Figure 1: Parts list
`1`	Top cover	√
`2`	Air baffle for middle drive cage			√
`3`	OCP 3.0 Ethernet adapter	√
`4`	Riser bracket (low profile)	√
`5`	Riser bracket (full-height, full-length)	√
`6`	Riser bracket (low profile + low profile)	√
`7`	Internal riser bracket (low profile)	√
`8` `9` `10`	Riser card	√
`11`	Intrusion switch	√
`12`	TPM adapter (For Chinese Mainland only)		√
`13`	Standard air baffle			√
`14`	PIB board		√
`15`	Fan board		√
`16`	M.2 bracket	√
`17`	M.2 drive	√
`18`	M.2 retainer clip	√
`19`	RAID super capacitor	√
`20`	M.2/riser support bracket	√
`21`	RAID super capacitor holder	√
`22`	Rear hot-swap drive cage	√
`23`	Rear SAS/SATA backplane	√
`24`	Rear NVMe backplane	√
`25`	Power supply	√
`26`	Power supply filler	√
`27`	PCIe adapter	√
`28`	Chassis		√
`29`	Front I/O assembly, server models with four 3.5-inch drive bays	√
`30`	Front I/O assembly, server models with eight or ten 2.5-inch drive bays	√
`31`	Security bezel	√
`32`	System board		√
`33`	Filler, 2.5-inch drive			√
`34`	Storage drive, 2.5-inch, hot-swap	√
`35`	Filler, 3.5-inch drive			√
`36`	Storage drive, 3.5-inch, hot-swap	√
`37`	System fan	√
`38`	Backplane, ten 2.5-inch hot-swap drives	√
`39`	Backplane, eight 2.5-inch hot-swap drives	√
`40`	Backplane, four 3.5-inch hot-swap drives	√
`41`	Backplane, ten 2.5-inch AnyBay hot-swap drives	√
`42`	Middle backplane, four 2.5-inch hot-swap drives	√
`43`	Memory module	√
`44`	Heat sink		√
`45`	Internal drive cage, four 2.5-inch hot-swap drives			√
`46`	Rear wall bracket			√
`47`	CMOS battery			√
`48`	Processor		√

Give documentation feedback