Skip to main content

Hard disk drive problems

Table 1. Hard disk drive symptoms and actions.

The hard disk drive symptoms and actions table with one level of row and column headers.

SymptomAction
Not all drives are recognized by the hard disk drive diagnostic test.Remove the drive that is indicated by the diagnostic tests; then, run the hard disk drive diagnostic test again. If the remaining drives are recognized, replace the drive that you removed with a new one.
The server stops responding during the hard disk drive diagnostic test.Remove the hard disk drive that was being tested when the server stopped responding, and run the diagnostic test again. If the hard disk drive diagnostic test runs successfully, replace the drive that you removed with a new one.
A hard disk drive was not detected while the operating system was being started.Reseat all hard disk drives and cables; then, run the hard disk drive diagnostic test.
A hard disk drive passes the diagnostic Fixed Disk Test, but the problem remains.Run the diagnostic SCSI Fixed Disk Test. See Running DSA Preboot diagnostic program.
Note
This test is not available on servers that have RAID arrays or servers that have SATA hard disk drives.
A hard disk drive has failed, and the associated yellow hard disk drive status LED is lit. (hot-swap hard disk drives)
  1. Reconfigure the integrated SAS/SATA controller with RAID capabilities and the devices that are attached to it.
  2. Run the DSA disk drive test. See Dynamic System Analysis.
  3. If the drive fails the test, replace the drive.
A newly installed hard disk drive is not recognized.
  1. Observe the associated yellow hard disk drive status LED. If the LED is lit, it indicates a drive fault.
  2. If the LED is lit, remove the drive from the bay, wait 45 seconds, and reinsert the drive, making sure that the drive assembly connects to the hard-disk-drive backplane.
  3. Observe the associated green hard disk drive activity LED and the yellow status LED:
    • If the green activity LED is flashing and the yellow status LED is not lit, the drive is recognized by the controller and is working correctly. Run the DSA hard disk drive test to determine whether the drive is detected.
    • If the green activity LED is flashing and the yellow status LED is flashing slowly, the drive is recognized by the controller and is rebuilding.
    • If neither LED is lit or flashing, check the hard-disk-drive backplane (go to step 4).
    • If the green activity LED is flashing and the yellow status LED is lit, replace the drive. If the activity of the LEDs remains the same, go to step 4. If the activity of the LEDs changes, return to step 1.
  4. Make sure that the hard-disk-drive backplane is correctly seated. When it is correctly seated, the drive assemblies correctly connect to the backplane without bowing or causing movement of the backplane.
  5. Reseat the backplane power cable and repeat steps 1 through 3.
  6. Reseat the backplane signal cable and repeat steps 1 through 3.
  7. Suspect the backplane signal cable or the backplane:
    • Replace the affected backplane signal cable.
    • Replace the affected backplane.
  8. Run the DSA tests for the SAS/SATA adapter and hard disk drives. SeeDynamic System Analysis.
    • If the adapter passes the test but the drives are not recognized, replace the backplane signal cable and run the tests again.
    • Replace the backplane.
    • If the adapter fails the test, disconnect the backplane signal cable from the adapter and run the tests again.
    • If the adapter fails the test, replace the adapter.
  9. See Problem determination tips.
Multiple hard disk drives fail.

Make sure that the hard disk drive, RAID card, and server device drivers and firmware are at the latest level.

Important
Some cluster solutions require specific code levels or coordinated code updates. If the device is part of a cluster solution, verify that the latest level of code is supported for the cluster solution before you update the code.
Multiple hard disk drives are offline.
  1. Review the storage subsystem logs for indications of problems within the storage subsystem, such as backplane or cable problems.
  2. See Problem determination tips.
A replacement hard disk drive does not rebuild.
  1. Make sure that the hard disk drive is recognized by the adapter (the green hard disk drive activity LED is flashing).
  2. Review the SAS/SATA RAID adapter documentation to determine the correct configuration parameters and settings.
A green hard disk drive activity LED does not accurately represent the actual state of the associated drive. (hot-swap hard disk drives)
  1. If the green hard disk drive activity LED does not flash when the drive is in use, run the DSA disk drive test. See Dynamic System Analysis.
  2. Use one of the following procedures:
    • If the drive passes the test, replace the backplane.
    • If the drive fails the test, replace the drive.
A yellow hard disk drive status LED does not accurately represent the actual state of the associated drive. (hot-swap hard disk drives)
  1. If the yellow hard disk drive LED and the RAID card software do not indicate the same status for the drive, do the following:
    1. Turn off the server.
    2. Reseat the SAS/SATA adapter.
    3. Reseat the backplane signal cable and power cable.
    4. Reseat the hard disk drive.
    5. Turn on the server and observe the activity of the hard disk drive LEDs.
  2. See Problem determination tips.