Skip to main content

Replacing the DVD drive

Use this information to replace the DVD drive

If you are replacing a drive, make sure that:
  • You have all the cables and other equipment that are specified in the documentation that comes with the new drive.
  • You have checked the instructions that come with the new drive to determine whether you must set any switches or jumpers in the drive.
  • You have removed the blue optical drive rails from the side of the old drive and have them available for installation on the new drive.
Note
If you are installing a drive that contains a laser, observe the following safety precautions.

Statement 3


Exclamation symbol
CAUTION
When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or transmitters) are installed, note the following:
  • Do not remove the covers. Removing the covers of the laser product could result in exposure to hazardous laser radiation. There are no serviceable parts inside the device.
  • Use of controls or adjustments or performance of procedures other than those specified herein might result in hazardous radiation exposure.

Exclamation symbol
DANGER
danger

Some laser products contain an embedded Class 3A or Class 3B laser diode.

Note the following. Laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam.


Laser class 1 symbol

To install a DVD drive on 4U server models with non-hot-swap power supplies, complete the following steps. For the 5U server model with hot-swap power supplies, please see the next sub-section.

  1. Read the safety information in Safety and Installation guidelines.
  2. Follow the instructions that come with the drive to set jumpers or switches, if there are any.
    Note
    You might find it easier to install the new drive from the front and then attach the cables.
  3. Touch the static-protective package that contains the new DVD drive to any unpainted metal surface on the server; then, remove the DVD drive from the package and place it on a static-protective surface.
  4. Stand the server back up in its vertical position.
  5. Remove the drive retainer clip from the side of the drive cage of bay 1 or bay 2. Slide the drive retainer clip to the front to remove it from the drive cage; then, snap the drive retainer clip into the screw holes on the side of the drive.
  6. Push the drive into the bay.
    Figure 1. DVD drive installation for 4U server models with non-hot-swap power supplies
    DVD drive installation for 4U server models with non-hot-swap power supplies
  7. Carefully turn the server on its side so that it is lying flat.
    Attention
    Do not allow the server to fall over.
  8. Connect the power (power connector P9) and signal cables to the drive.
    Note
    Route the signal cable so that it does not block the airflow to the rear of the drives or over the microprocessor and dual inline memory modules (DIMMs).
  9. If you have another drive to install or remove, do so now.
  10. Install the side cover (see Replacing the side cover).
  11. Install the bezel (see Replacing the bezel).
    Note
    Remove the filler blocking the installed drive if any.
  12. Reconnect the external cables and power cords; then, turn on the attached devices and turn on the server.

To install a DVD drive on the 5U server model with hot-swap power supplies, complete the following steps. For 4U server models with non-hot-swap power supplies, please see the above sub-section.

  1. Read the safety information in Safety and Installation guidelines.
  2. Follow the instructions that come with the drive to set jumpers or switches, if there are any.
    Note
    You might find it easier to install the new drive from the front and then attach the cables.
  3. Touch the static-protective package that contains the new DVD drive to any unpainted metal surface on the server; then, remove the DVD drive from the package and place it on a static-protective surface.
  4. Attach the drive retainer clip that you removed from the previous drive to the side of the new drive.
  5. Push the drive into the bay.
    Figure 2. DVD drive installation for 5U server model with hot-swap power supplies
    DVD drive installation for 5U server model with hot-swap power supplies
  6. Connect the power and signal cables to the drive.
    Note
    Route the signal cable so that it does not block the airflow to the rear of the drives or over the microprocessor and dual inline memory modules (DIMMs).
  7. Install the upper bezel (see Replacing the upper bezel).
  8. Install the lower bezel (see Replacing the lower bezel).
  9. Install and lock the side cover (see Replacing the side cover).
  10. Reconnect the external cables and power cords; then, turn on the attached devices and turn on the server.